Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chip
- Fanless
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '65'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
There are two hardware models of the HPE 1920-8g-poe switch. The version
currently in the repository is the model with a PoE budget of 180W. In
preparation of the addition of the 65W model, the existing model is
renamed to clarify the hardware version it targets.
As suggested by Pawel, the 'SUPPORTED_DEVICES' includes the old target
name to enable an upgrade path of builds with the old name.
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
The driver for the cellular modems serial interface was missing from the
default device packages.
The driver is required to interact with the modem using AT commands.
Other devices with a 4G modem also ship with this package, thus let's
add it to the default packages for the board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix broken onhub dtsi. The gmac node have a redundant phy-handle that
doesn't point to the swconfig phy node as they got dropped in the DSA
conversion. Drop these extra binding to restore correct compilation of
this subtarget.
Fixes: 337e36e0ef ("ipq806x: convert each device to DSA implementation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The node name&label should match the address in the 'reg' property,
so it's better to change the incorrect offset to the 0x28.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM
size is 0xe00.
Fixes: ac68fbf526 ("ramips: add support for I-O DATA WN-DEAX1800GR")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This adds the following changes:
b4f76ecc9e Ignore MAP_VARIABLE in tst-mman-consts.py
f5d377c896 __check_pf: Add a cancellation cleanup handler [BZ #20975]
0e3e9dbb0e Document BZ #20975 fix
e2974d26ce io: Fix record locking contants on 32 bit arch with 64 bit default time_t (BZ#30477)
3593050c27 io: Fix F_GETLK, F_SETLK, and F_SETLKW for powerpc64
8dcb1a5181 hppa: xfail debug/tst-ssp-1 when have-ssp is yes (gcc-12 and later)
0930ff8eb3 realloc: Limit chunk reuse to only growing requests [BZ #30579]
3f4b4e2cdd elf: _dl_find_object may return 1 during early startup (bug 30515)
260d4b742b nptl: Fix tst-cancel30 on sparc64
58f7431fd7 sparc: Fix la_symbind for bind-now (BZ 23734)
1caf955269 x86: Increase `non_temporal_threshold` to roughly `sizeof_L3 / 4`
80a8c858a5 x86: Fix slight bug in `shared_per_thread` cache size calculation.
cc8243fb0b x86: Use `3/4*sizeof(per-thread-L3)` as low bound for NT threshold.
f94ff95e93 x86: Fix incorrect scope of setting `shared_per_thread` [BZ# 30745]
0d500bfdc0 hurd: Make exception subcode a long
be26b29262 io: Fix record locking contants for powerpc64 with __USE_FILE_OFFSET64
3d24d1903d elf: Do not run constructors for proxy objects
a7e34a6675 elf: Always call destructors in reverse constructor order (bug 30785)
bdb594afa5 elf: Remove unused l_text_end field from struct link_map
1a7cbe52c8 elf: Move l_init_called_next to old place of l_text_end in link map
b752934602 CVE-2023-4527: Stack read overflow with large TCP responses in no-aaaa mode
6529a7466c (HEAD) getaddrinfo: Fix use after free in getcanonname (CVE-2023-4806)
79310b45af x86/dl-cacheinfo: remove unsused parameter from handle_amd
9d5c6e27ed x86: Fix for cache computation on AMD legacy cpus.
4473d1b87d Fix leak in getaddrinfo introduced by the fix for CVE-2023-4806 [BZ #30843]
94ef701365 Document CVE-2023-4806 and CVE-2023-5156 in NEWS
2dfd8c77b5 i686: Regenerate ulps
b4e23c75ae tunables: Terminate if end of input is reached (CVE-2023-4911)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current code fails if we have package or host tools with no patches
to apply. The error printend is the following: (taking ubus as an
example)
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[2]: 'conf' is up to date.
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[1]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt'
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
The source directory contains no quilt patches.
make[2]: *** [Makefile:81: quilt-check] Error 1
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
time: package/system/ubus/refresh#0.06#0.00#0.07
ERROR: package/system/ubus failed to build.
make[1]: *** [package/Makefile:120: package/system/ubus/refresh] Error 1
make[1]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt'
make: *** [/home/ansuel/openwrt-ansuel/openwrt/include/toplevel.mk:232: package/ubus/refresh] Error 2
We exit 1 after saying that there are no patches because later in the
function quilt pop fails to execute.
Having no patches for a package and calling refresh should not be
a critical error and the function should just do nothing.
To handle this improve quilt.mk with the following addition.
- If we don't have any patch for the package, we print a warning and we
create an empty series. This is useful to trick quilt and make it do
nothing.
We also create a status file .quilt_no_patch to detect in the other
function that we don't have patches to handle.
- In refresh makefile target, we check if .quilt_no_patch exist and
we skip quilt cleanup if this exist.
- In RefreshDir function we change the logic and now we delete the
patches directory and not only the content. This is done as a cleanup
to clean case with empty patches directory.
- In RefreshDir we check if .quilt_no_patch exist and we skip creating
the patches directory and copying the refreshed patches.
- In RefreshDir we delete at the end any trace of .quilt_no_patch if
present.
This is needed to support run like package/refresh that will run the
refresh process on any package present in the buildroot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To better reference them for diagnostic use, reference the PATCH_DIR and
FILES_DIR with the absolute path instead of using ./ and reference by
the relative location.
No behaviour change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport qca8k fixes for big endian system (to make them working again)
and a patch fixing MDIO conflicts if other PHY are connected and mgmt
eth is used to control the switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch enabling assisted learning for qca8k to fix roaming issue
between BSS and BSS on the same L2 broadcast domain.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in
the DSA driver upstream and conflicts as they are EXPORTED.
Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix
the conflict. While at it also make them static and drop the
EXPORT_SYMBOL_GPL as they are not actually used by any other driver and
exporting them is useless.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In userspace, ASLR is enabled, but it's missing to enable KASLR on the
kernel side to improve security as part of SystemReady recommendations.
Signed-off-by: Javier Tia <javier.tia@linaro.org>
The name of the variable holding the pointer to the private struct has
changed between Linux 5.15 and Linux 6.1 and adding the identical patch
fixing PCIe #PERST de-assert broke the build on Linux 6.1.
Also change the name in the patch to fix the build.
Fixes: 6a2e17d5c1 ("mediatek: fix PCIe #PERST being de-asserted too early")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix copy-paste error in migrating NEC Aterm WG2600HP3 to new LED
implementation for the QCA8K switch. Correct define the missing
additional LED pin used for each port and fix wrong color for LED 2 for
each port. Also add the required function-enumerator as all 3 LED have
the same color and function.
Fixes: c707cff6c9 ("ipq806x: add LEDs definition for non-standard qca8k LEDs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
This script was used to modify the wrong machine type passed
from the boot loader to the kernel. The device tree kernels
does not use the machine type so this script is no longer
needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point in keeping the v5.15 kernel around for Gemini,
we are maintaining the platform with a strong upstream focus and
newer is always better.
Now that OpenWrt can support pure v6.1 kernels, switch up to
v6.1 and drop v5.15 so we don't need to migrate configs and
patches for no reason.
The USB FOTG2 module handling can be simplified as a result.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix Spanning Tree Protocol (STP) by changing COPY2CPU which currently
makes switch to ignore Bridge Protocol Data Units (BPDUs).
Tested on Zyxel GS1900-8, 24 and 48.
Signed-off-by: Rudolf Vesely <i@rudolfvesely.com>
[ improve commit description and add new line in different sections ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When cmake is invoked to build a package it usually reports a warning
about unused variables passed to it. This is caused by openwrt passing
all supported variables to cmake, even if they are not all required by
the package being compiled.
To reduce clutter when compiling such packages these warnings are now
suppressed.
Approved-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tjalling Hattink <t.hattink@fugro.com>
The USXGMII implementation of Realtek switches can not only support
10GbE but also 2.5Gb and 5Gb on top of the usual data rates.
Mark those as supported to allow them to be negotiated.
This change has been tested on a ZyXEL XGS1250-12 with the following link
partners:
- NWA50AX Pro (2.5Gb)
- RTL8152 USB NIC (2.5Gb)
- AQC111 USB NIC (2.5Gb & 5Gb)
Gbit and 10GbE has also been tested to still work fine with a variety of
devices.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This condition was introduced in commit 51c8f76612 ("realtek: Improve
MAC config handling for all SoCs") to correctly report the speed of the
internal serdes ports as 10G, but instead makes all ports read 10G
because the or-operator should have been an and-operator.
Fixes: #9953
Fixes: 51c8f76612 ("realtek: Improve MAC config handling for all SoCs")
Signed-off-by: Peter Körner <git@mazdermind.de>
[ wrap comment to 72 column and improve commit ref ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The driver for MediaTek gen3 PCIe hosts de-asserts all reset
signals at the same time using a single register write operation.
Delay the de-assertion of the #PERST signal by 100ms as some PCIe
devices fail to come up otherwise.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Google WiFi board has what seems as debug version of TZ/QSEE and it is
always enabling SDI (Secure Debug Image) and in order to do a regular
reboot it must be disabled, as otherwise you are stuck in a debug state
where you are supposed to extract debug logs via QCA tooling which is not
helpfull at all for regular users.
So, instead of using our downstream version to disable SDI lets use the
version that was merged upstream and relies on a boolean property in the
SCM node instead of checking the compatible.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Improve and update instructions on how to add board files and both
describe the needed step to upstream a board file or to use it locally.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.
This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.
Fixes: e3aa645b26
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
