mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-24 15:43:25 +00:00
ipq806x: add support for Extreme Networks AP3935
Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
This commit is contained in:
Glen Lee
Christian Marangi
parent
89895937dd
commit
3aef61060e
@ -38,6 +38,10 @@ askey,rt4230w-rev6)
|
||||
edgecore,ecw5410)
|
||||
ubootenv_add_uci_config "/dev/mtd11" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
extreme,ap3935)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
|
||||
ubootenv_add_uci_config "/dev/mtd3" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
linksys,ea7500-v1|\
|
||||
linksys,ea8500)
|
||||
ubootenv_add_uci_config "/dev/mtd10" "0x0" "0x20000" "0x20000"
|
||||
|
||||
@ -33,6 +33,10 @@ edgecore,ecw5410)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt"
|
||||
;;
|
||||
extreme,ap3935)
|
||||
ucidef_set_led_netdev "wan" "wan" "orange:lan1" "eth1"
|
||||
ucidef_set_led_netdev "lan" "lan" "orange:lan2" "eth0"
|
||||
;;
|
||||
meraki,mr52)
|
||||
ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0"
|
||||
ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1"
|
||||
|
||||
@ -39,7 +39,8 @@ ipq806x_setup_interfaces()
|
||||
tplink,onhub)
|
||||
ucidef_set_interfaces_lan_wan "lan1" "wan"
|
||||
;;
|
||||
edgecore,ecw5410)
|
||||
edgecore,ecw5410 |\
|
||||
extreme,ap3935)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
;;
|
||||
qcom,ipq8064-ap161)
|
||||
|
||||
@ -15,6 +15,11 @@ case "$board" in
|
||||
ubnt,unifi-ac-hd)
|
||||
macaddr_add $(mtd_get_mac_binary EEPROM 0x6) $(($PHYNBR + 1)) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
extreme,ap3935)
|
||||
echo "##### PHYNBR=$PHYNBR DEVPATH=$DEVPATH"
|
||||
[ "$PHYNBR" = "0" ] && echo $(mtd_get_mac_ascii CFG1 RADIOADDR0) > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && echo $(mtd_get_mac_ascii CFG1 RADIOADDR1) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
esac
|
||||
|
||||
OPATH=${DEVPATH##/devices/platform/}
|
||||
|
||||
@ -12,6 +12,9 @@ boot() {
|
||||
edgecore,ecw5410)
|
||||
fw_setenv bootcount 0
|
||||
;;
|
||||
extreme,ap3935)
|
||||
fw_setenv WATCHDOG_COUNT 0x00000000
|
||||
;;
|
||||
linksys,ea7500-v1 |\
|
||||
linksys,ea8500)
|
||||
mtd resetbc s_env || true
|
||||
|
||||
@ -44,6 +44,11 @@ platform_do_upgrade() {
|
||||
fi
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
extreme,ap3935)
|
||||
CI_ROOTPART="nand_flash"
|
||||
CI_KERNPART="PriImg"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
linksys,ea7500-v1 |\
|
||||
linksys,ea8500)
|
||||
platform_do_upgrade_linksys "$1"
|
||||
|
||||
@ -318,6 +318,7 @@ CONFIG_NVMEM_QCOM_QFPROM=y
|
||||
# CONFIG_NVMEM_QCOM_SEC_QFPROM is not set
|
||||
# CONFIG_NVMEM_SPMI_SDAM is not set
|
||||
CONFIG_NVMEM_SYSFS=y
|
||||
CONFIG_NVMEM_U_BOOT_ENV=y
|
||||
CONFIG_OF=y
|
||||
CONFIG_OF_ADDRESS=y
|
||||
CONFIG_OF_EARLY_FLATTREE=y
|
||||
|
||||
@ -0,0 +1,351 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq8064-v2.0.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Extreme Networks AP3935";
|
||||
compatible = "extreme,ap3935", "qcom,ipq8064";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x41400000 0x3ec00000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi7_serial;
|
||||
serial1 = &gsbi2_serial;
|
||||
mdio-gpio0 = &mdio0;
|
||||
ethernet0 = &gmac0;
|
||||
ethernet1 = &gmac2;
|
||||
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_orange;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-override = "ubi.block=0,0 root=/dev/ubiblock0_0";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_power_green: power_green {
|
||||
label = "green:power";
|
||||
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_orange: power_orange {
|
||||
label = "orange:power";
|
||||
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan2g_green {
|
||||
label = "green:wlan2g";
|
||||
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led_wlan5g_green {
|
||||
label = "green:wlan5g";
|
||||
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
led_lan1_green {
|
||||
label = "green:lan1";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_lan1_orange {
|
||||
label = "orange:lan1";
|
||||
gpios = <&qcom_pinmux 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_lan2_green {
|
||||
label = "green:lan2";
|
||||
gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_lan2_orange {
|
||||
label = "orange:lan2";
|
||||
gpios = <&qcom_pinmux 29 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&qcom_pinmux {
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19";
|
||||
function = "gsbi5";
|
||||
drive-strength = <10>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
function = "gsbi5";
|
||||
drive-strength = <12>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
function = "gpio";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio22", "gpio23", "gpio24", "gpio25",
|
||||
"gpio26", "gpio27", "gpio28", "gpio29";
|
||||
function = "gpio";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio56";
|
||||
function = "gpio";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi2 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "okay";
|
||||
|
||||
gsbi2_serial: serial@12490000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi4 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "okay";
|
||||
|
||||
serial@16340000 {
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi7 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "okay";
|
||||
|
||||
gsbi7_serial: serial@16640000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "okay";
|
||||
|
||||
spi4: spi@1a280000 {
|
||||
status = "okay";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
|
||||
cfg1@02a0000 {
|
||||
compatible = "u-boot,env-redundant-bool";
|
||||
label = "CFG1";
|
||||
reg = <0x02a0000 0x0010000>;
|
||||
|
||||
ethaddr: ethaddr {
|
||||
};
|
||||
};
|
||||
|
||||
bootpri@02b0000 {
|
||||
label = "BootPRI";
|
||||
reg = <0x02b0000 0x0080000>;
|
||||
};
|
||||
|
||||
cfg2@0330000 {
|
||||
label = "CFG2";
|
||||
reg = <0x0330000 0x0010000>;
|
||||
};
|
||||
|
||||
fs@0340000 {
|
||||
label = "FS";
|
||||
reg = <0x0340000 0x0080000>;
|
||||
};
|
||||
|
||||
priimg@03c0000 {
|
||||
label = "PriImg";
|
||||
reg = <0x03c0000 0x0e10000>;
|
||||
};
|
||||
|
||||
secimg@11d0000 {
|
||||
label = "SecImg";
|
||||
reg = <0x11d0000 0x0e10000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
/delete-property/ pinctrl-0;
|
||||
/delete-property/ pinctrl-names;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
|
||||
/delete-property/ pinctrl-0;
|
||||
/delete-property/ pinctrl-names;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
compatible = "qcom,nandcs";
|
||||
|
||||
reg = <0>;
|
||||
|
||||
nand-ecc-strength = <8>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
ubi@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0000000 0x20000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&soc {
|
||||
mdio1: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
phy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "okay";
|
||||
|
||||
qcom,id = <0>;
|
||||
mdiobus = <&mdio1>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
phy-handle = <&phy1>;
|
||||
|
||||
nvmem-cells = <ðaddr>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "okay";
|
||||
|
||||
qcom,id = <2>;
|
||||
mdiobus = <&mdio1>;
|
||||
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy2>;
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "okay";
|
||||
};
|
||||
@ -160,6 +160,23 @@ define Device/edgecore_ecw5410
|
||||
endef
|
||||
TARGET_DEVICES += edgecore_ecw5410
|
||||
|
||||
define Device/extreme_ap3935
|
||||
$(call Device/LegacyImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Extreme Networks
|
||||
DEVICE_MODEL := AP3935
|
||||
SOC := qcom-ipq8068
|
||||
PAGESIZE := 2048
|
||||
BLOCKSIZE := 128k
|
||||
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
|
||||
KERNEL_LOADADDR = 0x41408000
|
||||
KERNEL_SIZE := 14400k
|
||||
KERNEL_SUFFIX := -uImage
|
||||
UBINIZE_OPTS := -E 5
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += extreme_ap3935
|
||||
|
||||
define Device/linksys_ea7500-v1
|
||||
$(call Device/LegacyImage)
|
||||
$(Device/kernel-size-migration)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user