It still requires fixing PCIe support:
[ 6.644699] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges:
[ 6.652217] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff]
[ 6.661833] OF: /axi@18000000/pcie@12000: Missing device_type
[ 6.667622] pcie_iproc_bcma: probe of bcma0:7 failed with error -12
[ 6.673985] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges:
[ 6.681514] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff]
[ 6.691137] pcie_iproc_bcma: probe of bcma0:8 failed with error -12
[ 6.697522] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges:
[ 6.705048] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff]
[ 6.714669] pcie_iproc_bcma: probe of bcma0:9 failed with error -12
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The label-mac logic relies on the mac-address property of a netdev
devices of-node. However, the mac address can also be stored as a
different property or read from e.g. an mtd device.
Create this node when reading a mac-address from OF if it does not
already exist and copy the mac-address used for the device to this
property. This way, the MAC address can be accessed using procfs.
Signed-off-by: David Bauer <mail@david-bauer.net>
46d02c2 block: don't add non-ubifs ubi devices
cc63933 blockd: send mount.ready when startup has completed
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The LEDs for LAN1 and LAN3 were swapped. Link on port 1 would illuminate
the LED on port 3 and vice versa.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without explicit configuration of these pins the ethernet as well as
status LED of the device do not work correctly.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit b309248730.
This commit could create a property without allocated memory, breaking
subsequent reads over a nodes property. Also, the mac-address-increment
was not applied when reading from nvmem.
Revert this commit for now, which breaks the label-mac-address logic.
Possibly, traversing the device-tree from the netdev side is easier
anyways.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM
* 802.11n 2T2R (external antennas)
* QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas)
* 3x 10/100 LAN, 1x 10/100 WAN
* UART header with pinout printed on PCB
Installation:
* The device comes with a bootloader installed only
* The bootloader offers DHCP and is reachable at http://10.123.123.1
* Accept the agreement and flash sysupgrade.bin
* Use Firefox if flashing does not work
TFTP recovery with static IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server at 192.168.0.66
* Keep the reset button pressed for 4 seconds after connecting power
TFTP recovery with dynamic IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server with a DHCP server running at the same address
* Keep the reset button pressed for 6 seconds after connecting power
Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
This patch did not apply cleanly any more after support for the XTX
flash was added to the generic patches.
Fixes: 92012dd867 ("kernel: Add support for XTX XT26G02A SPI NAND")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware wtmi_app.bin for all Armada 3720 devices.
This firmware includes additional features like access to Hardware
Random Number Generator of Armada 3720 SoC which original Marvell's
fuse.bin image does not have.
Add a patch which allows to pass the commit id, so the firmware is able
to identify itself, see a04bffeb.
Add a patch to disable linking with gold, since the ARM toolchain
doesn't ship gold.
Cherry-pick the 3 post-release fixes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
02e23db fix compilation errors popped up by GCC-10
7c35173 Merge pull request #29 from pali/sync-a38x-uboot
bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE
ee1ea84 mv_ddr: a38x: Fix ddr3 compilation
70f3e2e mv_ddr: Fix comment typo
dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter
a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT
3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map
Signed-off-by: Andre Heider <a.heider@gmail.com>
2efdb10 wtmi: Fix calculation of UART divider
4247e39 fix: twin die ddr porting guide
8ad7992 sys_init: Add missing newlines in debug mode
4ddea19 avs: Validate VDD value from OTP
c444aeb avs: Fix description for avs value 0x2e
1915b78 tim: Optimize code generated by gettimver.sh and print newline
21f566d tim: Print mv_ddr version and configuration on UART
840b70b tim: Use variable $DDRFILE where possible
c10e6ae tim: Fix waiting for UART TX ready
7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO
63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes
e949b58 wtmi: During setup clock phase print CPU and DDR speed
10376b5 wtmi: Flush output on UART after the '\n' character
509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid
Signed-off-by: Andre Heider <a.heider@gmail.com>
Revert to using the checked in `tbb_linux` image tool binary since building
it drags in the rather big Crypto++ project.
Cherry-pick the post-release UART fixes.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This patch has been carried since introduction throughout every kernel
major bump and no one has tested if the later kernels improved the
situation. The Armada 3720 SoC can only process GbE interrupts on Core 0
and this is already limited in all stable kernels, so ditch this
workaround for 64 bit SoCs.
Ref: https://git.kernel.org/torvalds/c/cf9bf871280d
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Enable the Microsemi phy driver to support the VSC8514 QSGMII phy on the
FRWY-LS1046A board.
Otherwise, the "Generic PHY" driver is used.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
commit 2c2d77bd3b ("layerscape: add FRWY-LS1046A board support")
missed to add an entry to the 79_move_config preinit script.
Therefore, the config transfer on sysupgrade wass broken for this device.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This reverts commit b7ee0786b5.
With the previous commit "realtek: remove rtl83xx vlan 1 special cases"
this is no longer required.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
On reset, the PVID of all ports is set to 1; if this is reset to 0,
the special cases for VLAN 1 are no longer required.
port_vlan_add is called with vid=0 when the DSA port interfaces are
enabled with no VLAN; previously the VLAN was not configured in this
case, relying on VLAN 1 being present, but with the PVID set to 0,
configuring VLAN 0 as normal works as expected.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain
precal binaries in ART, and the precal in the cards eeprom causes
firmware load errors.
These firmware files were previously in linux-firmware,
so these are adding them back and renaming to be cleaner.
Signed-off-by: Damien Mascord <tusker@tusker.org>
Add a patch to fix building with GCC 11, which triggers new warnings by
enabling -Warray-parameter by default.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add CONFIG_HAVE_ARM_ARCH_TIMER (disabled). A make kernel_oldconfig on cortexa9
will otherwise prompt for its selection. The 5.4 configuration already contains
the same symbol.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add the new CONFIG_BATTERY_RT5033 to the generic configuration, as reported by
Paul Blazejowski. Resort the kconfig while at it.
No deleted or manually refreshed patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
Latest binutils (2.37) exposed a long-standing bug. The kernel linking stage
would break at the SORTTAB step, due to the exception table having been
previously purged from vmlinux, as its section wasn't marked as unconditionally
kept. Fix thusly.
Additionally, the "#define ARM_MMU_DISCARD(x) KEEP(x)" change is bogus. It
would only apply to !CONFIG_MMU devices (which we don't support in OpenWrt), and
it would even break the build if referenced. Drop it.
While at it, rename the patch in order to make it obvious that it's
arm-specific.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Add same changes for kernel 5.4 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
85f01c44a950 bridge: check bridge port vlan membership on link-up events
17e453bd68b4 wireless: add back regular virtual interfaces on hotplug-add events as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
772292e uxc: don't restart containers when mount shows up
3a9d910 uxc: resolve volume UUIDs by name of UCI fstab section
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch fixes the fifo rx mode for the mt7623. It is already accepted
upstream for Linux Kernel 5.15.
To test the spi we can change the dts file to
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
spidev: spidev@0 {
compatible = "linux,spidev";
spi-max-frequency = <1000000>;
reg = <0>;
};
};
Afterwards we should see a spidev device under /dev/.
To test it we can further use spidev-test.
Signed-off-by: Nick Hainke <vincent@systemli.org>
a846c6b blockd: fix length of timeout int passed to ioctl
1d681ca block: support umount device basename
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
59f7c11 blockd: create mountpoint parent folder if needed
9cc96af Revert "block: resolve /dev/mapper/* name for /dev/dm-0 when hotplugging"
06334ac Revert "blockd: detect mountpoint of /dev/mapper/*"
9ab3551 block: use /dev/dm-* instead of /dev/mapper/*
5114595 block: allow remove hotplug event to arrive at blockd
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nvmem require the device node to be registered with the of_platform.
Register the device node so that nvmem can correctly find the dev and
correctly load the mac-addr stored in the nvmem cell declared in the dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
When the kmod-qlcnic package is built on targets that have
CONFIG_PCI_IOV enabled, the CONFIG_QLCNIC_SRIOV symbol is exposed.
Enable this symbol in the kmod package to fix its build.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
A missing quote in target/linux/ath79/patches-5.x/920-mikrotik-rb4xx.patch
produces:
...
scripts/kconfig/conf --syncconfig Kconfig
drivers/mfd/Kconfig:2016:warning: multi-line strings not supported
...
This patch adds missing closing quote, fixing the above warning.
Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
