Remove the remaining configuration entries that were omitted in the
previous commit.
Fixes: 1576474f55 ("ramips: switch to 6.1 kernel")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.
Specifications:
- SoC: Filogic 820 MT7981A (1.3GHz)
- RAM: DDR4 512M
- Flash: eMMC 8G, MicroSD card slot
- WiFi: 2.4GHz and 5GHz with 6 antennas
- Ethernet:
- 1x LAN (10/100/1000M)
- 1x WAN (10/100/1000/2500M)
- 5G: Quectel RM520N-GL with two nano-SIM card slots
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
vendor OpenWrt address source
WAN eth0 label factory 0x0a (label)
LAN eth1 label + 1
2g phy0-ap0 label + 2 factory 0x04
5g phy1-ap0 label + 3
Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware
Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
- 0,0 indicates that the network port uses the USB interface
- 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
- 'AT+QCFG="data_interface",0,0' to use the USB interface
- 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Reference: b40da332df
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commit faa5f17fe2 ("kernel: mtk_eth_soc: release
MAC_MCR_FORCE_LINK only when MAC is up") to Linux 5.15 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
dnsmasq was recently updated to 2.90, but PKG_RELEASE was not reset to 1.
Fixes: 838a27f64f ("dnsmasq: version 2.90")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 5.15 kenel config file, patches and version switches will be
removed in this patch. We will introduce kernel 6.6 support soon.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
libevent2's cmake use absolute path, then cmake cannot find it when cross compiling:
```
-- Found libevent include directory: /builder/staging_dir/target-mips_24kc_musl/usr/include
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_core.so
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_extra.so
-- Found libevent component: /builder/staging_dir/target-mips_24kc_musl/usr/lib/libevent_openssl.so
-- Found libevent 2.1.12 in /builder/staging_dir/target-mips_24kc_musl/usr
CMake Error at /builder/staging_dir/target-mips_24kc_musl/usr/lib/cmake/libevent/LibeventTargets-shared.cmake:102 (message):
The imported target "libevent::core" references the file
"/usr/lib/libevent_core-2.1.so.7.0.1"
but this file does not exist. Possible reasons include:
* The file was deleted, renamed, or moved to another location.
* An install or uninstall procedure did not complete successfully.
* The installation package was faulty and contained
"/builder/staging_dir/target-mips_24kc_musl/usr/lib/cmake/libevent/LibeventTargets-shared.cmake"
but not all the files it references.
Call Stack (most recent call first):
/builder/staging_dir/target-mips_24kc_musl/usr/lib/cmake/libevent/LibeventConfig.cmake:168 (include)
CMakeLists.txt:34 (find_package)
```
This patch make cmake use relative imported path, so it can find libevent.
Signed-off-by: Liu Dongmiao <liudongmiao@gmail.com>
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.
Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.
Depends on PR #14584 (which introduced an `if` block)
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
When kernel 6.6 is being compiled with GCC13 it will prompt for:
Compressed Debug information
> 1. Don't compress debug information (DEBUG_INFO_COMPRESSED_NONE)
2. Compress debugging information with zlib (DEBUG_INFO_COMPRESSED_ZLIB)
3. Compress debugging information with zstd (DEBUG_INFO_COMPRESSED_ZSTD) (NEW)
This is because kernel now also has support for compressing debug info
with ZSTD, so add the missing symbol and disable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The YunCore G720 is a dual band 802.11ax router with 5 GbE ports.
Specs:
- SoC: MediaTek MT7621
- Ethernet: 5x GbE ports (built-in MT7530)
- Wireless 2.4GHz / 5GHz: MediaTek MT7915E
- RAM: 256MiB
- ROM: 16MiB (W25Q128)
- 1 Button (reset)
- 8 LEDs (1x system, 2x wifi, 5x switch ports)
Flash instructions:
The vendor firmware is based on OpenWrt, the sysupgrade image can be
flashed using the '-F' (force) option on the CLI.
Make sure not to keep settings when doing so.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We have had the testing kernel for several weeks now. Let's switch to 6.1
to have more testers. Additionally, 6.6 is already in the pipeline.
Signed-off-by: Nick Hainke <vincent@systemli.org>
CONFIG_HID_SUPPORT:
Set default value for kmod-hid
CONFIG_USB_CDNS3_IMX:
CONFIG_USB_CDNS3_PCI_WRAP:
CONFIG_USB_CDNSP_PCI:
Introduced by db0d7cf6a1 (usb: add cdns3 support)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This reverts commit 7ea82bc17d.
This commit does not meet formal requirments, and has been merged due to
my error.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_DEBUG_INFO_COMPRESSED_ZSTD, required by GCC 13.0+
Compress the debug information using zstd. This may provide better compression than zlib, for about the same time costs, but requires newer toolchain support. Requires GCC 13.0+ or Clang 16.0+, binutils 2.40+, and zstd.
Signed-off-by: CharlesMengCA <58993776+CharlesMengCA@users.noreply.github.com>
Recent changes for Linux 6.6 broke things when building with older
kernels:
Package kmod-fs-jfs is missing dependencies for the following libraries:
nls_base.ko
Fix this by adding NLS dependencies after the added dependency applying
on Linux 6.6.
Fixes: f9198480da ("kernel: modules: fs: adapt for kernel 6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As shared remove functions now returns void instead of int we need to
use .remove_new instead of .remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A new patch was added meanwhile which will go as fix via netdev tree.
Copy & refresh it for Linux 6.6 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A commit introduced in kernel 6.6 has splitted page_pool.h into
several headers. Thus the included header must be modified for a
successful build.
Ref: a9ca9f9ceff3 (page_pool: split types and declarations from
page_pool.h)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Now that geniv is packaged separately for kernel 6.6, we need to add it
as a dependency to kmod-crypto-seqiv and kmod-crypto-echainiv that require
it under kernel 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
geniv was separated intentionally from aead in kernel 6.5, and since
we now have it packaged separately as well remove it from kmod-aead
in 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In kernel 6.5 geniv was split from AEAD config symbol, in order to manage
its dependencies on other code.
So, lets do the same in OpenWrt and split it from aead module so others
can depend on geniv directly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt hwmon kmods for building under kernel 6.6:
* ad7418 now requires regmap
* Invert criteria to allow adt7410 be built with Linux 6.1 as well
as Linux 6.6.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Adapt crypto kmods for building under kernel 6.6:
* mpi.ko moved from lib/mpi/mpi.ko to lib/crypto/mpi/mpi.ko
* jitterentropy_rng requires SHA3 support for kernel 6.6
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt video kmods for building under kernel 6.6:
* Add drm_exec.ko and drm_suballoc_helper.ko for kmod-drm as they
are added since 6.6 and 6.4
* Add uvc.ko for kmod-video-uvc as related contents was split as a
new module since 6.3
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt block kmods for building under kernel 6.6:
* To build scsi_transport_iscsi.ko, change CONFIG_SCSI_ISCSI_ATTRS
from =y to =m as this config is always tristate since 2.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt fs kmods for building under kernel 6.6:
* Add kmod-fs-netfs as dependency for kmod-fs-9p
* Add kmod-fs-netfs as dependency for fs-smbfs-common as netfs is
required for cifs since 6.3
* Add new kmod-nls-ucs2-utils as dependency for smbfs/jfs as UCS2
support was split as new module since 6.6.
* Add kmod-lib-zlib-deflate and kmod-lib-zlib-inflate as
dependencies for kmod-pstore due to crypto API compression was
replaced with zlib_deflate library calls since 6.6
* Remove nfs_ssc.ko from kmod-fs-nfs-common. The nfs_ssc was no
longer a kernel module described by NFS_V4_2_SSC_HELPER since 5.13 [1]
Link:
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/fs/Kconfig?id=d9092b4bb2109502eb8972021a3f74febc931a63
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt usb kmods for building under kernel 6.6:
* Add kmod-phylink as dependency for usb-net-asix
* Add kmod-net-selftests as dependency for usb-net-smsc95xx
* Add kmod-iio-core as dependency for usb-hid-mcp2221 as ADC/DAC
support was added since 6.2 which requires IIO.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
