I moved xor-image into image-commands.mk to use it in ath79 target.
It required for NEC WG800HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Refresh all patches
Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch
Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.
Tested-on: ath79
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
We need to use resolved file list as prerequisites for repacking kmod
.ipk files. Note that currently version_filter uses a Makefile macro
KERNEL_PATCHVER that should be available at ipk building time.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This command enables factory image generation for Cameo boards. On
upgrade the vendor firmware will check the size of the provided image
and if a specific string is located at the end of the binary.
cameo-factory will generate an image that the vendor firmware accepts.
Tested on a D-Link DIR-825 C1 with vendor firmwares 3.01 and 3.04.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.
Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some kernel modules from kmod-ipt-conntrack-extra depend on
nf_conncount.ko, which was added in kernel 4.16, add it to the kmod.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_socket.ko module was split in commit 8db4c5be88f ("netfilter:
move socket lookup infrastructure to nf_socket_ipv{4,6}.c") into a
common, n IPv4 and an IPv6 part.
The nf_tproxy.ko module was split in commit 45ca4e0cf27 ("netfilter:
Libify xt_TPROXY") into a common, an IPv4 and an IPv6 part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit a0ae2562c6c ("netfilter: conntrack: remove l3proto
abstraction") The modules nf_conntrack_ipv4.ko, nf_conntrack_ipv6.ko and
nf_conntrack.ko were squashed together into one module. This module now
depends on nf_defrag_ipv6 when IPv6 support was activated. This is part
of the main netfilter packages, so add nf_defrag_ipv6.ko also to the
default netfilter packages on kernel 4.19 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They are no longer stored in the "testing" subdirectory and are not
available as .tar.xz archives. If -rc is detected download it from the
git.kernel.org and use .tar.gz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Consider following use case:
define Device/apalis
...
FILESYSTEMS := ext4 squashfs
IMAGES := spl-uboot.bin recovery.scr
IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
IMAGE/recovery.scr := recovery-scr
endef
Where we would get target binaries with following filenames:
openwrt-imx6-apalis-squashfs.recovery.scr
openwrt-imx6-apalis-squashfs.spl-uboot.bin
openwrt-imx6-apalis-ext4.recovery.scr
openwrt-imx6-apalis-ext4.spl-uboot.bin
With proposed patch, we could now just do:
define Device/apalis
...
ARTIFACTS := spl-uboot.bin recovery.scr
ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
ARTIFACT/recovery.scr := recovery-scr
endef
Which would produce target binaries with following filenames:
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-spl-uboot.bin
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The -rcX "testing" kernels are no longer hosted on
cdn.kernel.org file servers directly in a "testing"
directory. Therefore the logic that tested for "-rc"
can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add a basic variant which provides WPA-PSK only, 802.11r and 802.11w and
is intended to support 11r & 11w (subject to driver support) out of the
box.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The tl-wa850re-v2 images from the ar71xx/tiny target are getting too big
with the default packages. The size check is done before the meta data
is added so there is no file to add meta data to or to sign. Originally
errors in Build/append-metadata were getting ignored, but if the signing
fails the error is not ignored.
This adds a check if the file to be signed is there and only does the
signing if it is there. This way it does not fail if the package
creation was already aborted earlier.
Fixes: 848b455d2e ("image: use ucert to append signature")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
