* The declaration of peer_session_create() does
not match its definition. As it is only
used inside of peers.c make it static.
* Make the declaration of peers_register_table()
match its definition.
* Also, make all functions in peers.c that
are not also in peers.h static
Since IPv6 is a different type than IPv4, the pattern fetch functions
src6 and dst6 were added. IPv6 stick-tables can also fetch IPv4 addresses
with src and dst. In this case, the IPv4 addresses are mapped to their
IPv6 counterpart, according to RFC 4291.
Since the latest additions to buffer_forward(), it became too large for
inlining, so let's uninline it. The code size drops by 3kB. Should be
backported to 1.4 too.
Despite much care around handling the content-length as a 64-bit integer,
forwarding was broken on 32-bit platforms due to the 32-bit nature of
the ->to_forward member of the "buffer" struct. The issue is that this
member is declared as a long, so while it works OK on 64-bit platforms,
32-bit truncate the content-length to the lower 32-bits.
One solution could consist in turning to_forward to a long long, but it
is used a lot in the critical path, so it's not acceptable to perform
all buffer size computations on 64-bit there.
The fix consists in changing the to_forward member to a strict 32-bit
integer and ensure in buffer_forward() that only the amount of bytes
that can fit into it is considered. Callers of buffer_forward() are
responsible for checking that their data were taken into account. We
arbitrarily ensure we never consider more than 2G at once.
That's the way it was intended to work on 32-bit platforms except that
it did not.
This issue was tracked down hard at Exosec with Bertrand Jacquin,
Thierry Fournier and Julien Thomas. It remained undetected for a long
time because files larger than 4G are almost always transferred in
chunked-encoded format, and most platforms dealing with huge contents
these days run on 64-bit.
The bug affects all 1.5 and 1.4 versions, and must be backported.
And also rename "req_acl_rule" "http_req_rule". At the beginning that
was a bit confusing to me, especially the "req_acl" list which in fact
holds what we call rules. After some digging, it appeared that some
part of the code is 100% HTTP and not just related to authentication
anymore, so let's move that part to HTTP and keep the auth-only code
in auth.c.
It's very annoying that frontend and backend stats are merged because we
don't know what we're observing. For instance, if a "listen" instance
makes use of a distinct backend, it's impossible to know what the bytes_out
means.
Some points take care of not updating counters twice if the backend points
to the frontend, indicating a "listen" instance. The thing becomes more
complex when we try to add support for server side keep-alive, because we
have to maintain a pointer to the backend used for last request, and to
update its stats. But we can't perform such comparisons anymore because
the counters will not match anymore.
So in order to get rid of this situation, let's have both frontend AND
backend stats in the "struct proxy". We simply update the relevant ones
during activity. Some of them are only accounted for in the backend,
while others are just for frontend. Maybe we can improve a bit on that
later, but the essential part is that those counters now reflect what
they really mean.
This patch turns internal server addresses to sockaddr_storage to
store IPv6 addresses, and makes the connect() function use it. This
code already works but some caveats with getaddrinfo/gethostbyname
still need to be sorted out while the changes had to be merged at
this stage of internal architecture changes. So for now the config
parser will not emit an IPv6 address yet so that user experience
remains unchanged.
This change should have absolutely zero user-visible effect, otherwise
it's a bug introduced during the merge, that should be reported ASAP.
This one has been removed and is now totally superseded by ->target.
To get the server, one must use target_srv(&s->target) instead of
s->srv now.
The function ensures that non-server targets still return NULL.
This is in fact where those parts belong to. The old data_state was replaced
by applet.state and is now initialized when the applet is registered. It's
worth noting that the applet does not need to know the session nor the
buffer anymore since everything is brought by the stream interface.
It is possible that having a separate applet struct would simplify the
code but that's not a big deal.
When doing a connect() on a stream interface, some information is needed
from the server and from the backend. In some situations, we don't have
a server and only a backend (eg: peers). In other cases, we know we have
an applet and we don't want to connect to anything, but we'd still like
to have the info about the applet being used.
For this, we now store a pointer to the "target" into the stream interface.
The target describes what's on the other side before trying to connect. It
can be a server, a proxy or an applet for now. Later we'll probably have
descriptors for multiple-stage chains so that the final information may
still be found.
This will help removing many specific cases in the code. It already made
it possible to remove the "srv" and "be" parameters to tcpv4_connect_server().
I/O handlers are still delicate to manipulate. They have no type, they're
just raw functions which have no knowledge of themselves. Let's have them
declared as applets once for all. That way we can have multiple applets
share the same handler functions and we can store their names there. When
we later need to add more parameters (eg: usage stats), we'll be able to
do so in the applets themselves.
The CLI functions has been prefixed with "cli" instead of "stats" as it's
clearly what is going on there.
The applet descriptor in the stream interface should get all the applet
specific data (st0, ...) but this will be done in the next patch so that
we don't pollute this one too much.
Debugging parsing errors can be greatly improved if we know what the parser
state was and what the buffer flags were (especially for closed inputs/outputs
and full buffers). Let's add that to the error snapshots.
Enhance pattern convs and fetch argument parsing, now fetchs and convs callbacks used typed args.
Add more details on error messages on parsing pattern expression function.
Update existing pattern convs and fetchs to new proto.
Create stick table key type "binary".
Manage Truncation and padding if pattern's fetch-converted result don't match table key size.
The introduction of a new PROXY protocol for proxied connections requires
an early analyser to decode the incoming connection and set the session
flags accordingly.
Some more work is needed, among which setting a flag on the session to
indicate it's proxied, and copying the original parameters for later
comparisons with new ACLs (eg: real_src, ...).
The stats web interface must be read-only by default to prevent security
holes. As it is now allowed to enable/disable servers, a new keyword
"stats admin" is introduced to activate this admin level, conditioned by ACLs.
(cherry picked from commit 5334bab92ca7debe36df69983c19c21b6dc63f78)
Based on a patch provided by Judd Montgomery, it is now possible to
enable/disable servers from the stats web interface. This allows to select
several servers in a backend and apply the action to them at the same time.
Currently, there are 2 known limitations :
- The POST data are limited to one packet
(don't alter too many servers at a time).
- Expect: 100-continue is not supported.
(cherry picked from commit 7693948766cb5647ac03b48e782cfee2b1f14491)
There was no consistency between all the functions used to exchange data
between a buffer and a stream interface. Also, the functions used to send
data to a buffer did not consider the possibility that the buffer was
shutdown for read.
Now the functions are called buffer_{put,get}_{char,block,chunk,string}.
The old buffer_feed* functions have been left available for existing code
but marked deprecated.
Signal zero is never delivered by the system. However having a signal to
which functions and tasks can subscribe to be notified of a stopping event
is useful. So this patch does two things :
1) allow signal zero to be delivered from any function of signal handler
2) make soft_stop() deliver this signal so that tasks can be notified of
a stopping condition.
The two new functions below make it possible to register any number
of functions or tasks to a system signal. They will be called in the
registration order when the signal is received.
struct sig_handler *signal_register_fct(int sig, void (*fct)(struct sig_handler *), int arg);
struct sig_handler *signal_register_task(int sig, struct task *task, int reason);
In case of HTTP keepalive processing, we want to release the counters tracked
by the backend. Till now only the second set of counters was released, while
it could have been assigned by the frontend, or the backend could also have
assigned the first set. Now we reuse to unused bits of the session flags to
mark which stick counters were assigned by the backend and to release them as
appropriate.
The assumption that there was a 1:1 relation between tracked counters and
the frontend/backend role was wrong. It is perfectly possible to track the
track-fe-counters from the backend and the track-be-counters from the
frontend. Thus, in order to reduce confusion, let's remove this useless
{fe,be} reference and simply use {1,2} instead. The keywords have also been
renamed in order to limit confusion. The ACL rule action now becomes
"track-sc{1,2}". The ACLs are now "sc{1,2}_*" instead of "trk{fe,be}_*".
That means that we can reasonably document "sc1" and "sc2" (sticky counters
1 and 2) as sort of patterns that are available during the whole session's
life and use them just like any other pattern.
Having a single tracking pointer for both frontend and backend counters
does not work. Instead let's have one for each. The keyword has changed
to "track-be-counters" and "track-fe-counters", and the ACL "trk_*"
changed to "trkfe_*" and "trkbe_*".
It's a bit cumbersome to have to know all possible storable types
from the stats interface. Instead, let's have generic types for
all data, which will facilitate their manipulation.
It is now possible to dump a table's contents with keys, expire,
use count, and various data using the command above on the stats
socket.
"show table" only shows main table stats, while "show table <name>"
dumps table contents, only if the socket level is admin.
This patch adds support for the following session counters :
- http_req_cnt : HTTP request count
- http_req_rate: HTTP request rate
- http_err_cnt : HTTP request error count
- http_err_rate: HTTP request error rate
The equivalent ACLs have been added to check the tracked counters
for the current session or the counters of the current source.
This function looks up a key, updates its expiration date, or creates
it if it was not found. acl_fetch_src_updt_conn_cnt() was updated to
make use of it.
These counters maintain incoming connection rates and session rates
in a stick-table, over a period which is defined in the configuration
(2 ms to 24 days). They can be used to detect service abuse and
enforce a certain accept rate per source address for instance, and
block if the rate is passed over.
Example :
# block if more than 50 requests per 5 seconds from a source.
stick-table type ip size 200k expire 1m store conn_rate(5s),sess_rate(5s)
tcp-request track-counters src
tcp-request reject if { trk_conn_rate gt 50 }
# cause a 3 seconds pause to requests from sources in excess of 20 requests/5s
tcp-request inspect-delay 3s
tcp-request content accept if { trk_sess_rate gt 20 } WAIT_END
We're now able to return errors based on the validity of an argument
passed to a stick-table store data type. We also support ARG_T_DELAY
to pass delays to stored data types (eg: for rate counters).
Some data types will require arguments (eg: period for a rate counter).
This patch adds support for such arguments between parenthesis in the
"store" directive of the stick-table statement. Right now only integers
are supported.
When a session tracks a counter, automatically increase the cumulated
connection count. This makes src_updt_conn_cnt() almost useless. In
fact it might still be used to update different tables.
The new "conn_cur" session counter has been added. It is automatically
updated upon "track XXX" directives, and the entry is touched at the
moment we increment the value so that we don't consider further counter
updates as real updates, otherwise we would end up updating upon completion,
which may not be desired. Probably that some other event counters (eg: HTTP
requests) will have to be updated upon each event though.
This counter can be matched against current session's source address using
the "src_conn_cur" ACL.
This patch adds the ability to set a pointer in the session to an
entry in a stick table which holds various counters related to a
specific pattern.
Right now the syntax matches the target syntax and only the "src"
pattern can be specified, to track counters related to the session's
IPv4 source address. There is a special function to extract it and
convert it to a key. But the goal is to be able to later support as
many patterns as for the stick rules, and get rid of the specific
function.
The "track-counters" directive may only be set in a "tcp-request"
statement right now. Only the first one applies. Probably that later
we'll support multi-criteria tracking for a single session and that
we'll have to name tracking pointers.
No counter is updated right now, only the refcount is. Some subsequent
patches will have to bring that feature.
The buffer_feed* functions that are used to send data to buffers did only
support sending contiguous chunks while they're relying on memcpy(). This
patch improves on this by making them able to write in two chunks if needed.
Thus, the buffer_almost_full() function has been improved to really consider
the remaining space and not just what can be written at once.
Some freq counters will have to work on periods different from 1 second.
The original freq counters rely on the period to be exactly one second.
The new ones (freq_ctr_period) let the user define the period in ticks,
and all computations are operated over that period. When reading a value,
it indicates the amount of events over that period too.
Simon Horman
Willy Tarreau
David du Colombier
Emeric Brun
Cyril Bonté