It's easier to take the counter's age into account when consulting it
than to rotate it first. It also saves some CPU cycles and avoids the
multiply for outdated counters, finally saving CPU cycles here too
when multiple operations need to read the same counter.
The freq_ctr code has also shrinked by one third consecutively to these
optimizations.
term_trace was very useful while reworking the lower layers but has almost
completely been removed from every place it was referenced. Even the few
remaining ones were not accurate, so it's better to completely remove those
references and re-add them from scratch later if needed.
In pure TCP mode, there is no response analyser to switch the server-side
stream interface from INI to CLO when the output has been closed after an
abort. This caused sessions to remain indefinitely active when they were
aborted by the client during a TCP content analysis.
The proper action is to switch the stream interface to the CLO state from
INI when we have write enable and shutdown write.
The rate-limit was applied to the smoothed value which does a special
case for frequencies below 2 events per period. This caused irregular
limitations when set to 1 session per second.
The proper way to handle this is to compute the number of remaining
events that can occur without reaching the limit. This is what has
been added. It also has the benefit that the frequency calculation
is now done once when entering event_accept(), before the accept()
loop, and not once per accept() loop anymore, thus saving a few CPU
cycles during very high loads.
With this fix, rate limits of 1/s are perfectly respected.
The new "rate-limit sessions" statement sets a limit on the number of
new connections per second on the frontend. As it is extremely accurate
(about 0.1%), it is efficient at limiting resource abuse or DoS.
These new ACLs match frontend session rate and backend session rate.
Examples are provided in the doc to explain how to use that in order
to limit abuse of service.
With this change, all frontends, backends, and servers maintain a session
counter and a timer to compute a session rate over the last second. This
value will be very useful because it varies instantly and can be used to
check thresholds. This value is also reported in the stats in a new "rate"
column.
Several algorithms will need to know the millisecond value within
the current second. Instead of doing a divide every time it is needed,
it's better to compute it when it changes, which is when now and now_ms
are recomputed.
curr_sec_ms_scaled is the same multiplied by 2^32/1000, which will be
useful to compute some ratios based on the position within last second.
The new "show errors" command sent on a unix socket will dump
all captured request and response errors for all proxies. It is
also possible to bound the log to frontends and backends whose
ID is passed as an optional parameter.
The output provides information about frontend, backend, server,
session ID, source address, error type, and error position along
with a complete dump of the request or response which has caused
the error.
If a new error scratches the one currently being reported, then
the dump is aborted with a warning message, and processing goes
on to next error.
Each proxy instance, either frontend or backend, now has some room
dedicated to storing a complete dated request or response in case
of parsing error. This will make it possible to consult errors in
order to find the exact cause, which is particularly important for
troubleshooting faulty applications.
If an invalid character is encountered while parsing an HTTP message, we
want to get buf->lr updated to reflect it.
Along this change, a few useless __label__ declarations have been removed
because they caused gcc to consume stack space without putting anything
there.
On overloaded systems, it sometimes happens that hundreds or thousands
of incoming connections are queued in the system's backlog, and all get
dequeued at once. The problem is that when haproxy processes them and
does not apply any limit, this can take some time and the internal date
does not progress, resulting in wrong timer measures for all sessions.
The most common effect of this is that all of these sessions report a
large request time (around several hundreds of ms) which is in fact
caused by the time spent accepting other connections. This might happen
on shared systems when the machine swaps.
For this reason, we finally apply a reasonable limit even in mono-process
mode. Accepting 100 connections at once is fast enough for extreme cases
and will not cause that much of a trouble when the system is saturated.
Problem reported by John Lauro. When "source ... usesrc ..." is
set in the defaults section, it is not possible anymore to remove
the "usesrc" part when declaring a more precise "source" in a
backend. The only workaround was to declare it by server.
We need to clear optional settings when declaring a new "source".
The problem was the same with the "interface" declaration.
Unix socket processing was still quite buggy. It did not properly
handle interrupted output due to a full response buffer. The fix
mainly consists in not trying to prematurely enable write on the
response buffer, just like the standard session works. This also
gets the unix socket code closer to the standard session code
handling.
Commit 8a5c626e73 introduced the sessions
dump on the unix socket. This implementation is buggy because it may try
to link to the sessions list's head after the last session is removed
with a backref. Also, for the LIST_ISEMPTY test to succeed, we have to
proceed with LIST_INIT after LIST_DEL.
Some parts from the previous doc about logging have been merged and
updated. Most of those parts have been reworked and completed. The
examples are now accurate and reflect recent versions.
As subject when i try to compile haproxy with -DDEBUG_FULL it stop at
stream_sock.c file with:
gcc -Iinclude -Wall -O2 -g -DDEBUG_FULL -DTPROXY -DENABLE_POLL
-DENABLE_EPOLL -DENABLE_SEPOLL -DNETFILTER -DUSE_GETSOCKNAME
-DCONFIG_HAPROXY_VERSION=\"1.3.15\"
-DCONFIG_HAPROXY_DATE=\"2008/04/19\" -c -o src/stream_sock.o
src/stream_sock.c
src/stream_sock.c: In function 'stream_sock_chk_rcv':
src/stream_sock.c:905: error: 'fd' undeclared (first use in this function)
src/stream_sock.c:905: error: (Each undeclared identifier is reported only once
src/stream_sock.c:905: error: for each function it appears in.)
src/stream_sock.c:905: error: 'ob' undeclared (first use in this function)
src/stream_sock.c: In function 'stream_sock_chk_snd':
src/stream_sock.c:940: error: 'fd' undeclared (first use in this function)
src/stream_sock.c:940: error: 'ib' undeclared (first use in this function)
make: *** [src/stream_sock.o] Error 1
With this patch all build fine:
Using the wrong operator (&& instead of &) causes DOWN->UP
transition to take longer than it should and to produce a lot of
redundant logs. With typical "track" usage (1-6 tracking servers) it
shouldn't make a big difference but for heavily tracked servers
this bug leads to hang with 100% CPU usage and extremely big
log spam.
The "bind-process" keyword lets the admin select which instances may
run on which process (in multi-process mode). It makes it easier to
more evenly distribute the load across multiple processes by avoiding
having too many listen to the same IP:ports.
Specifying "interface <name>" after the "source" statement allows
one to bind to a specific interface for proxy<->server traffic.
This makes it possible to use multiple links to reach multiple
servers, and to force traffic to pass via an interface different
from the one the system would have chosen based on the routing
table.
By appending "interface <name>" to a "bind" line, it is now possible
to specifically bind to a physical interface name. Note that this
currently only works on Linux and requires root privileges.
This will provide high performance data forwarding between sockets,
but it is broken on many kernels and will sometimes forward corrupted
data without some kernel patches. Consider this experimental for now.
Setting "nosplice" in the global section will disable the use of TCP
splicing (both tcpsplice and linux 2.6 splice). The same will be
achieved using the "-dS" parameter on the command line.
The global tuning options right now only concern the polling mechanisms,
and they are not in the global struct itself. It's not very practical to
add other options so let's move them to the global struct and remove
types/polling.h which was not used for anything else.
global.maxconn/4 seems to be a good hint for global.maxpipes when that
one must be guessed. If the limit is reached, it's still possible to
set it manually in the configuration.
Using pipe pools makes pipe management a lot easier. It also allows to
remove quite a bunch of #ifdefs in areas which depended on the presence
or not of support for kernel splicing.
The buffer now holds a pointer to a pipe structure which is always NULL
except if there are still data in the pipe. When it needs to use that
pipe, it dynamically allocates it from the pipe pool. When the data is
consumed, the pipe is immediately released.
That way, there is no need anymore to care about pipe closure upon
session termination, nor about pipe creation when trying to use
splice().
Another immediate advantage of this method is that it considerably
reduces the number of pipes needed to use splice(). Tests have shown
that even with 0.2 pipe per connection, almost all sessions can use
splice(), because the same pipe may be used by several consecutive
calls to splice().
A new data type has been added : pipes. Some pre-allocated empty pipes
are maintained in a pool for users such as splice which use them a lot
for very short times.
Pipes are allocated using get_pipe() and released using put_pipe().
Pipes which are released with pending data are immediately killed.
The struct pipe is small (16 to 20 bytes) and may even be further
reduced by unifying ->data and ->next.
It would be nice to have a dedicated cleanup task which would watch
for the pipes usage and destroy a few of them from time to time.
Did a full compile of the 1.3.15.7 - 20081208 snapshot on Freebsd-7.x
recently, and noted that there needs to be a quick patch done on the
Makefile for bsd machines.
This was due to the stream_interface replacing the send data commands
in the rewrite Willy did a while ago.
Simple fix, and it compiled cleanly otherwise. Thanks for the work
Willy!
Cheers,
Ross.
-=
Kernels before 2.6.27.13 would have splice() return EAGAIN on shutdown.
By adding a few tricks, we can deal with the situation. If splice()
returns EAGAIN and the pipe is empty, then fallback to recv() which
will be able to check if it's an end of connection or not.
The advantage of this method is that it remains transparent for good
kernels since there is no reason that epoll() will return EPOLLIN
without anything to read, and even if it would happen, the recv()
overhead on this check is minimal.
If splicing is enabled in a backend, we need to guess how many
pipes will be needed. We used to rely on fullconn, but this leads
to non-working splicing when fullconn is not specified. So we now
fallback to global.maxconn.
This code provides support for linux 2.6 kernel splicing. This feature
appeared in kernel 2.6.25, but initial implementations were awkward and
buggy. A kernel >= 2.6.29-rc1 is recommended, as well as some optimization
patches.
Using pipes, this code is able to pass network data directly between
sockets. The pipes are a bit annoying to manage (fd creation, release,
...) but finally work quite well.
Preliminary tests show that on high bandwidths, there's a substantial
gain (approx +50%, only +20% with kernel workarounds for corruption
bugs). With 2000 concurrent connections, with Myricom NICs, haproxy
now more easily achieves 4.5 Gbps for 1 process and 6 Gbps for two
processes buffers. 8-9 Gbps are easily reached with smaller numbers
of connections.
We also try to splice out immediately after a splice in by making
profit from the new ability for a data producer to notify the
consumer that data are available. Doing this ensures that the
data are immediately transferred between sockets without latency,
and without having to re-poll. Performance on small packets has
considerably increased due to this method.
Earlier kernels return only one TCP segment at a time in non-blocking
splice-in mode, while newer return as many segments as may fit in the
pipe. To work around this limitation without hurting more recent kernels,
we try to collect as much data as possible, but we stop when we believe
we have read 16 segments, then we forward everything at once. It also
ensures that even upon shutdown or EAGAIN the data will be forwarded.
Some tricks were necessary because the splice() syscall does not make
a difference between missing data and a pipe full, it always returns
EAGAIN. The trick consists in stop polling in case of EAGAIN and a non
empty pipe.
The receiver waits for the buffer to be empty before using the pipe.
This is in order to avoid confusion between buffer data and pipe data.
The BF_EMPTY flag now covers the pipe too.
Right now the code is disabled by default. It needs to be built with
CONFIG_HAP_LINUX_SPLICE, and the instances intented to use splice()
must have "option splice-response" (or option splice-request) enabled.
It is probably desirable to keep a pool of pre-allocated pipes to
avoid having to create them for every session. This will be worked
on later.
Preliminary tests show very good results, even with the kernel
workaround causing one memcpy(). At 3000 connections, performance
has moved from 3.2 Gbps to 4.7 Gbps.
