This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38699
When the mdio bus is unregistered the newly created phy will also be
unregistered and freed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38539
On some devices with e.g. a BCM2535F switch the second MAC is used, but
we can not find a phy under all addresses between 0 and 31, 0xffffffff
is returned as phy id. If we can not find a phy at the expected address
create a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38538
Without this patch we treated only phy addr 30 as an external phy, but
there is a register to check that. Now we do not have to try to reset
the switch to check for an external switch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38502
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
SVN-Revision: 38312
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38309
Add patches like they are currently in the mainline mips tree and add
some more pending patches for board detection.
* Now the board name is shown under machine in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38308
* do not try initialize a unused phy
* some improvements to the phylib patch
* do not turn the phy off when mac is off
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38306
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38294
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38288
This adds support for Byte Queue Limits in bgmac and b44, now it is
possible to use more advanced network queue control algorithms.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38038
This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38037
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 38011
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38005
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38004
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37999
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37998
* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes#14151.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37996
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37993
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
