ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
张鹏
Christian Lamparter
parent
59c2f8af8c
commit
bbab33724d
@ -18,7 +18,7 @@ endef
|
||||
# Please send a mail with your device-specific board files upstream.
|
||||
# You can find instructions and examples on the linux-wireless wiki:
|
||||
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
||||
ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3
|
||||
ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
|
||||
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
||||
|
||||
define Package/ipq-wifi-default
|
||||
@ -57,5 +57,6 @@ $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-networ
|
||||
$(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200))
|
||||
$(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3))
|
||||
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC))
|
||||
|
||||
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|
||||
|
||||
BIN
package/firmware/ipq-wifi/board-qxwlan-e2600ac.bin
Normal file
BIN
package/firmware/ipq-wifi/board-qxwlan-e2600ac.bin
Normal file
Binary file not shown.
@ -39,6 +39,11 @@ netgear,ex6150v2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
|
||||
;;
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN0" "e2600ac:green:wlan0" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN1" "e2600ac:green:wlan1" "phy1tpt"
|
||||
;;
|
||||
zyxel,nbg6617)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
|
||||
|
||||
@ -48,6 +48,12 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "3:lan" "4:lan"
|
||||
;;
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
||||
;;
|
||||
*)
|
||||
echo "Unsupported hardware. Network interfaces not initialized"
|
||||
;;
|
||||
|
||||
@ -135,6 +135,14 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ath10kcal_extract "0:ART" 4096 12064
|
||||
;;
|
||||
meraki,mr33)
|
||||
ath10kcal_ubi_extract "ART" 4096 12064
|
||||
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
|
||||
@ -145,12 +153,6 @@ case "$FIRMWARE" in
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
|
||||
;;
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62)
|
||||
ath10kcal_extract "0:ART" 4096 12064
|
||||
;;
|
||||
zyxel,nbg6617 |\
|
||||
zyxel,wre6606)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
@ -177,6 +179,14 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ath10kcal_extract "0:ART" 20480 12064
|
||||
;;
|
||||
meraki,mr33)
|
||||
ath10kcal_ubi_extract "ART" 20480 12064
|
||||
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
|
||||
@ -187,12 +197,6 @@ case "$FIRMWARE" in
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
|
||||
;;
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62)
|
||||
ath10kcal_extract "0:ART" 20480 12064
|
||||
;;
|
||||
zyxel,nbg6617 |\
|
||||
zyxel,wre6606)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
|
||||
@ -47,7 +47,8 @@ zyxel_do_upgrade() {
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
8dev,jalapeno |\
|
||||
alfa-network,ap120c-ac)
|
||||
alfa-network,ap120c-ac |\
|
||||
qxwlan,e2600ac-c2)
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
asus,map-ac2200)
|
||||
|
||||
@ -0,0 +1,80 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019-qxwlan-e2600ac.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Qxwlan E2600AC c1";
|
||||
compatible = "qxwlan,e2600ac-c1", "qcom,ipq4019";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@180000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -0,0 +1,115 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019-qxwlan-e2600ac.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Qxwlan E2600AC c2";
|
||||
compatible = "qxwlan,e2600ac-c2", "qcom,ipq4019";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x04000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
nand_pins: nand-pins {
|
||||
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -0,0 +1,262 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
|
||||
model = "Qxwlan E2600AC";
|
||||
compatible = "qcom,ipq4019";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>; /* 256MB */
|
||||
};
|
||||
|
||||
soc {
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
serial@78b0000 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
i2c@78b7000 { /* BLSP1 QUP2 */
|
||||
pinctrl-0 = <&i2c_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3: usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led1 {
|
||||
label = "e2600ac:green:wlan0";
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "e2600ac:green:wlan1";
|
||||
gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led3 {
|
||||
label = "e2600ac:green:usb";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led4 {
|
||||
label = "e2600ac:green:ctrl1";
|
||||
gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led5 {
|
||||
label = "e2600ac:green:ctrl2";
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led6 {
|
||||
label = "e2600ac:green:ctrl3";
|
||||
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
i2c_0_pins: i2c-0-pinmux {
|
||||
mux {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp_i2c0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: serial0-pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_1_pins: serial1_pinmux {
|
||||
mux {
|
||||
pins = "gpio8", "gpio9";
|
||||
function = "blsp_uart1";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
|
||||
};
|
||||
@ -0,0 +1,80 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019-qxwlan-e2600ac.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Qxwlan E2600AC c1";
|
||||
compatible = "qxwlan,e2600ac-c1";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@180000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -0,0 +1,115 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019-qxwlan-e2600ac.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Qxwlan E2600AC c2";
|
||||
compatible = "qxwlan,e2600ac-c2";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x04000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
nand_pins: nand-pins {
|
||||
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -0,0 +1,266 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
*
|
||||
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
|
||||
model = "Qxwlan E2600AC";
|
||||
compatible = "qcom,ipq4019";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>; /* 256MB */
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
serial@78b0000 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
i2c@78b7000 { /* BLSP1 QUP2 */
|
||||
pinctrl-0 = <&i2c_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3: usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led1 {
|
||||
label = "e2600ac:green:wlan0";
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "e2600ac:green:wlan1";
|
||||
gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led3 {
|
||||
label = "e2600ac:green:usb";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led4 {
|
||||
label = "e2600ac:green:ctrl1";
|
||||
gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led5 {
|
||||
label = "e2600ac:green:ctrl2";
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led6 {
|
||||
label = "e2600ac:green:ctrl3";
|
||||
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
i2c_0_pins: i2c-0-pinmux {
|
||||
mux {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp_i2c0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: serial0-pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_1_pins: serial1_pinmux {
|
||||
mux {
|
||||
pins = "gpio8", "gpio9";
|
||||
function = "blsp_uart1";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
|
||||
};
|
||||
@ -285,6 +285,31 @@ define Device/qcom_ap-dk04.1-c1
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_TITLE := Qxwlan E2600AC-C1 (nor flash)
|
||||
BOARD_NAME := e2600ac-c1
|
||||
DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c2
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_TITLE := Qxwlan E2600AC-C2 (nornand flash)
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c2
|
||||
|
||||
define Device/zyxel_nbg6617
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_DTS := qcom-ipq4018-nbg6617
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -697,7 +697,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -697,7 +697,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -29,6 +29,8 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4028-wpj428.dtb \
|
||||
+ qcom-ipq4029-gl-b1300.dtb \
|
||||
+ qcom-ipq4029-mr33.dtb \
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -785,11 +785,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -785,11 +785,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -32,6 +32,8 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4028-wpj428.dtb \
|
||||
+ qcom-ipq4029-gl-b1300.dtb \
|
||||
+ qcom-ipq4029-mr33.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user