ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD
This board has been supported in the ar71xx. Links: * https://mikrotik.com/product/RB912UAG-2HPnD * https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd This also supports the 5GHz flavour of the board. Hardware: * SoC: Atheros AR9342, * RAM: DDR 64MB, * SPI NOR: 64KB, * NAND: 128MB, * Ethernet: x1 10/100/1000 port with passive POE in, * Wi-Fi: 802.11 b/g/n, * PCIe, * USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A port -- both can be used for LTE modem, but only one can be used at any time. * LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED, Ethernet phy LED, * Button, * Beeper. Not working: * Button: it shares gpio line 15 with NAND ALE and NAND IO7, and current drivers doesn't easily support this configuration, * Beeper: it is connected to bit 5 of a serial shift register (tested with sysfs led trigger timer). But kmod-gpio-beeper doesn't work -- we left this as is for now. Flashing: * Use the RouterBOARD Reset button to enable TFTP netboot, boot kernel and initramfs and then perform sysupgrade. * From ar71xx OpenWrt firmware run: $ sysupgrade -F /tmp/<sysupgrade.bin> For more info see: https://openwrt.org/toh/mikrotik/common. Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
This commit is contained in:
Denis Kalashnikov
Koen Vandeputte
parent
820e660cd7
commit
695a1cd53c
@ -0,0 +1,212 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "mikrotik,routerboard-912uag-2hpnd", "qca,ar9342";
|
||||
model = "MikroTik RouterBOARD 912UAG-2HPnD";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
gpio_latch: gpio_latch {
|
||||
compatible = "gpio-latch";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 1 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 2 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 3 GPIO_ACTIVE_HIGH>,
|
||||
<0>, /* Not connected */
|
||||
<&gpio 13 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 14 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 15 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio 11 GPIO_ACTIVE_LOW>; /* Latch Enable */
|
||||
};
|
||||
|
||||
nand_gpio {
|
||||
compatible = "mikrotik,rb91x-nand";
|
||||
|
||||
gpios = <&gpio_latch 3 GPIO_ACTIVE_HIGH>, /* Read */
|
||||
<&gpio 4 GPIO_ACTIVE_HIGH>, /* Ready (RDY) */
|
||||
<&gpio_latch 5 GPIO_ACTIVE_LOW>, /* Chip Enable (nCE) */
|
||||
<&gpio_latch 6 GPIO_ACTIVE_HIGH>, /* Command Latch Enable (CLE) */
|
||||
<&gpio_latch 7 GPIO_ACTIVE_HIGH>, /* Address Latch Enable (ALE) */
|
||||
<&gpio 12 GPIO_ACTIVE_LOW>, /* Read/Write Enable (nRW) */
|
||||
<&gpio_latch 8 GPIO_ACTIVE_LOW>; /* Latch Enable (nLE) */
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "booter";
|
||||
reg = <0x0 0x0040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "kernel";
|
||||
reg = <0x0040000 0x03c0000>;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "ubi";
|
||||
reg = <0x0400000 0x7c00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "green:power";
|
||||
gpios = <&gpio_latch 1 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
user {
|
||||
label = "green:user";
|
||||
gpios = <&gpio_latch 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led1 {
|
||||
label = "green:led1";
|
||||
gpios = <&ssr 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "green:led2";
|
||||
gpios = <&ssr 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led3 {
|
||||
label = "green:led3";
|
||||
gpios = <&ssr 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led4 {
|
||||
label = "green:led4";
|
||||
gpios = <&ssr 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led5 {
|
||||
label = "green:led5";
|
||||
gpios = <&ssr 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
|
||||
usb_power {
|
||||
gpio-export,name = "power-usb";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&ssr 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
pcie_power {
|
||||
gpio-export,name = "power-pcie";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&ssr 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qca,ar7100-spi";
|
||||
|
||||
cs-gpios = <0>, <&gpio_latch 0 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "mikrotik,routerboot-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "routerboot";
|
||||
reg = <0x0 0x0>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
hard_config: hard_config {
|
||||
read-only;
|
||||
};
|
||||
|
||||
bios {
|
||||
size = <0x1000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
soft_config {
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ssr: ssr@1 {
|
||||
compatible = "fairchild,74hc595";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <1>;
|
||||
reg = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii-id";
|
||||
phy-handle = <&phy0>;
|
||||
pll-data = <0x02000000 0x00000101 0x00001313>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
rgmii-gmac0 = <1>;
|
||||
rgmii-enabled = <1>;
|
||||
rxd-delay = <1>;
|
||||
txd-delay = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -9,6 +9,15 @@ define Device/mikrotik_routerboard-493g
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_routerboard-493g
|
||||
|
||||
define Device/mikrotik_routerboard-912uag-2hpnd
|
||||
$(Device/mikrotik_nand)
|
||||
SOC := ar9342
|
||||
DEVICE_MODEL := RouterBOARD 912UAG-2HPnD
|
||||
DEVICE_PACKAGES += kmod-usb-ehci kmod-usb2 kmod-gpio-beeper
|
||||
SUPPORTED_DEVICES += rb-912uag-2hpnd
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_routerboard-912uag-2hpnd
|
||||
|
||||
define Device/mikrotik_routerboard-921gs-5hpacd-15s
|
||||
$(Device/mikrotik_nand)
|
||||
SOC := qca9558
|
||||
|
||||
@ -14,6 +14,7 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch1" \
|
||||
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
|
||||
;;
|
||||
mikrotik,routerboard-912uag-2hpnd|\
|
||||
mikrotik,routerboard-921gs-5hpacd-15s|\
|
||||
mikrotik,routerboard-lhg-2nd|\
|
||||
mikrotik,routerboard-sxt-5nd-r2|\
|
||||
@ -36,6 +37,7 @@ ath79_setup_macs()
|
||||
local mac_base="$(cat /sys/firmware/mikrotik/hard_config/mac_base)"
|
||||
|
||||
case "$board" in
|
||||
mikrotik,routerboard-912uag-2hpnd|\
|
||||
mikrotik,routerboard-921gs-5hpacd-15s|\
|
||||
mikrotik,routerboard-lhg-2nd|\
|
||||
mikrotik,routerboard-sxt-5nd-r2|\
|
||||
|
||||
@ -23,6 +23,7 @@ board=$(board_name)
|
||||
case "$FIRMWARE" in
|
||||
"ath9k-eeprom-ahb-18100000.wmac.bin")
|
||||
case $board in
|
||||
mikrotik,routerboard-912uag-2hpnd|\
|
||||
mikrotik,routerboard-lhg-2nd|\
|
||||
mikrotik,routerboard-sxt-5nd-r2|\
|
||||
mikrotik,routerboard-wapr-2nd)
|
||||
|
||||
@ -32,6 +32,7 @@ platform_do_upgrade() {
|
||||
|
||||
case "$board" in
|
||||
mikrotik,routerboard-493g|\
|
||||
mikrotik,routerboard-912uag-2hpnd|\
|
||||
mikrotik,routerboard-921gs-5hpacd-15s|\
|
||||
mikrotik,routerboard-922uags-5hpacd|\
|
||||
mikrotik,routerboard-sxt-5nd-r2)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user