caskd/openwrt
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

mvebu: Enable the A385 AP on 3.19

Browse Source 
In order for the image to be built, some patches need to be ported to 3.19.

Add the relevant patches. Note that most of them (if not all) should be merged
in 3.20, removing the need to carry them on then.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 44267
This commit is contained in:
Imre Kaloz 2015-02-05 15:41:07 +00:00
parent 9be491f084
commit 66e35c5246
7 changed files with 606 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

97
target/linux/mvebu/patches-3.19/019-mtd-nand-pxa3xx-Fix-PIO-FIFO-draining.patch Normal file
View File

@ -0,0 +1,97 @@
From 11aa9df4de06cc257327d783c5cb615989e87286 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Fri, 23 Jan 2015 15:18:27 +0100
Subject: [PATCH v2 1/2] mtd: nand: pxa3xx: Fix PIO FIFO draining
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bits read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/mtd/nand/pxa3xx_nand.c | 45 ++++++++++++++++++++++++++++++++++++------
1 file changed, 39 insertions(+), 6 deletions(-)
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 96b0b1d27df1..e6918befb951 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -23,6 +23,7 @@
#include <linux/mtd/partitions.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/jiffies.h>
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/of_device.h>
@@ -480,6 +481,38 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
nand_writel(info, NDCR, ndcr | int_mask);
}
+static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
+{
+ u32 *dst = (u32 *)data;
+
+ if (info->ecc_bch) {
+ while (len--) {
+ u32 timeout;
+
+ *dst++ = nand_readl(info, NDDB);
+
+ /*
+ * According to the datasheet, when reading
+ * from NDDB with BCH enabled, after each 32
+ * bits reads, we have to make sure that the
+ * NDSR.RDDREQ bit is set
+ */
+ timeout = jiffies + msecs_to_jiffies(5);
+ while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) {
+ if (!time_before(jiffies, timeout)) {
+ dev_err(&info->pdev->dev,
+ "Timeout on RDDREQ while draining the FIFO\n");
+ return;
+ }
+
+ cpu_relax();
+ }
+ }
+ } else {
+ __raw_readsl(info->mmio_base + NDDB, data, len);
+ }
+}
+
static void handle_data_pio(struct pxa3xx_nand_info *info)
{
unsigned int do_bytes = min(info->data_size, info->chunk_size);
@@ -496,14 +529,14 @@ static void handle_data_pio(struct pxa3xx_nand_info *info)
DIV_ROUND_UP(info->oob_size, 4));
break;
case STATE_PIO_READING:
- __raw_readsl(info->mmio_base + NDDB,
- info->data_buff + info->data_buff_pos,
- DIV_ROUND_UP(do_bytes, 4));
+ drain_fifo(info,
+ info->data_buff + info->data_buff_pos,
+ DIV_ROUND_UP(do_bytes, 4));
if (info->oob_size > 0)
- __raw_readsl(info->mmio_base + NDDB,
- info->oob_buff + info->oob_buff_pos,
- DIV_ROUND_UP(info->oob_size, 4));
+ drain_fifo(info,
+ info->oob_buff + info->oob_buff_pos,
+ DIV_ROUND_UP(info->oob_size, 4));
break;
default:
dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
--
2.2.2

70
target/linux/mvebu/patches-3.19/020-ARM-mvebu-Add-a-number-of-pinctrl-functions.patch Normal file
View File

@ -0,0 +1,70 @@
From 91b4c91f919abffa72cbf7545a944252f8e4f775 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Thu, 8 Jan 2015 18:38:08 +0100
Subject: [PATCH 3/4] ARM: mvebu: Add a number of pinctrl functions
Some pinctrl functions can be shared with all DTS out there, since they are
generic, SoC-wide muxing options. Add a number of these to the DTSI to avoid
duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/armada-38x.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 40200084c6c8..98885c58be29 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -195,6 +195,45 @@
pinctrl@18000 {
reg = <0x18000 0x20>;
+
+ ge0_rgmii_pins: ge-rgmii-pins-0 {
+ marvell,pins = "mpp6", "mpp7", "mpp8",
+ "mpp9", "mpp10", "mpp11",
+ "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "ge0";
+ };
+
+ i2c0_pins: i2c-pins-0 {
+ marvell,pins = "mpp2", "mpp3";
+ marvell,function = "i2c0";
+ };
+
+ mdio_pins: mdio-pins {
+ marvell,pins = "mpp4", "mpp5";
+ marvell,function = "ge";
+ };
+
+ ref_clk0_pins: ref-clk-pins-0 {
+ marvell,pins = "mpp45";
+ marvell,function = "ref";
+ };
+
+ spi1_pins: spi-pins-1 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59";
+ marvell,function = "spi1";
+ };
+
+ uart0_pins: uart-pins-0 {
+ marvell,pins = "mpp0", "mpp1";
+ marvell,function = "ua0";
+ };
+
+ uart1_pins: uart-pins-1 {
+ marvell,pins = "mpp19", "mpp20";
+ marvell,function = "ua1";
+ };
};
gpio0: gpio@18100 {
--
2.2.1

220
target/linux/mvebu/patches-3.19/021-ARM-mvebu-Add-Armada-385-Access-Point-Development-Bo.patch Normal file
View File

@ -0,0 +1,220 @@
From e5ee12817e9eac891c6b2a340f64d94d9abd355f Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Thu, 8 Jan 2015 18:38:09 +0100
Subject: [PATCH 4/4] ARM: mvebu: Add Armada 385 Access Point Development Board
support
The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.
[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/armada-385-db-ap.dts | 178 +++++++++++++++++++++++++++++++++
2 files changed, 179 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-385-db-ap.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6dc9c17f9ff5..d34837104949 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -536,6 +536,7 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
dtb-$(CONFIG_MACH_ARMADA_38X) += \
armada-385-db.dtb \
+ armada-385-db-ap.dtb \
armada-385-rd.dtb
dtb-$(CONFIG_MACH_ARMADA_XP) += \
armada-xp-axpwifiap.dtb \
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts
new file mode 100644
index 000000000000..57b9119fb3e0
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-db-ap.dts
@@ -0,0 +1,178 @@
+/*
+ * Device Tree file for Marvell Armada 385 Access Point Development board
+ * (DB-88F6820-AP)
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Nadav Haklai <nadavh@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada 385 Access Point Development Board";
+ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ spi1: spi@10680 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <54000000>;
+ };
+ };
+
+ i2c0: i2c@11000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+
+ /*
+ * This bus is wired to two EEPROM
+ * sockets, one of which holding the
+ * board ID used by the bootloader.
+ * Erasing this EEPROM's content will
+ * brick the board.
+ * Use this bus with caution.
+ */
+ };
+
+ mdio@72004 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@4 {
+ reg = <4>;
+ };
+
+ phy2: ethernet-phy@6 {
+ reg = <6>;
+ };
+ };
+
+ /* UART0 is exposed through the JP8 connector */
+ uart0: serial@12000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ /*
+ * UART1 is exposed through a FTDI chip
+ * wired to the mini-USB connector
+ */
+ uart1: serial@12100 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ };
+
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+
+ ethernet@70000 {
+ pinctrl-names = "default";
+
+ /*
+ * The Reference Clock 0 is used to
+ * provide a clock to the PHY
+ */
+ pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * The three PCIe units are accessible through
+ * standard mini-PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+
+ pcie@3,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ };
+ };
+};
--
2.2.1

39
target/linux/mvebu/patches-3.19/022-ARM-mvebu-A385-AP-Enable-the-NAND-controller.patch Normal file
View File

@ -0,0 +1,39 @@
From 7eb1f09ec8e25aa2fc3f6fc5fc9405d9f917d503 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Thu, 11 Dec 2014 14:14:58 +0100
Subject: [PATCH 1/2] ARM: mvebu: A385-AP: Enable the NAND controller
The A385 AP has a 1GB NAND chip. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
arch/arm/boot/dts/armada-385-db-ap.dts | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts
index 3a51531eb37b..02db04867d8f 100644
--- a/arch/arm/boot/dts/armada-385-db-ap.dts
+++ b/arch/arm/boot/dts/armada-385-db-ap.dts
@@ -122,6 +122,19 @@
phy = <&phy0>;
phy-mode = "rgmii-id";
};
+
+ nfc: flash@d0000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ num-cs = <1>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ };
};
pcie-controller {
--
2.2.1

43
target/linux/mvebu/patches-3.19/023-pinctrl-mvebu-a38x-Add-UART1-muxing-options.patch Normal file
View File

@ -0,0 +1,43 @@
From a95308d88c07e0093aedae7e64f92cb1e165f592 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Fri, 5 Dec 2014 15:44:57 +0100
Subject: [PATCH] pinctrl: mvebu: a38x: Add UART1 muxing options
The MPP19 and MMP20 pins also have the ability to be muxed to the uart1
function.
Add this case to the pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/pinctrl/mvebu/pinctrl-armada-38x.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-38x.c b/drivers/pinctrl/mvebu/pinctrl-armada-38x.c
index 224c6cff6aa2..7302f66f4f19 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-38x.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-38x.c
@@ -145,14 +145,16 @@ static struct mvebu_mpp_mode armada_38x_mpp_modes[] = {
MPP_VAR_FUNCTION(2, "ptp", "event_req", V_88F6810_PLUS),
MPP_VAR_FUNCTION(3, "pcie0", "clkreq", V_88F6810_PLUS),
MPP_VAR_FUNCTION(4, "sata1", "prsnt", V_88F6810_PLUS),
- MPP_VAR_FUNCTION(5, "ua0", "cts", V_88F6810_PLUS)),
+ MPP_VAR_FUNCTION(5, "ua0", "cts", V_88F6810_PLUS),
+ MPP_VAR_FUNCTION(6, "ua1", "rxd", V_88F6810_PLUS)),
MPP_MODE(20,
MPP_VAR_FUNCTION(0, "gpio", NULL, V_88F6810_PLUS),
MPP_VAR_FUNCTION(1, "ge0", "txclk", V_88F6810_PLUS),
MPP_VAR_FUNCTION(2, "ptp", "clk", V_88F6810_PLUS),
MPP_VAR_FUNCTION(3, "pcie1", "rstout", V_88F6820_PLUS),
MPP_VAR_FUNCTION(4, "sata0", "prsnt", V_88F6810_PLUS),
- MPP_VAR_FUNCTION(5, "ua0", "rts", V_88F6810_PLUS)),
+ MPP_VAR_FUNCTION(5, "ua0", "rts", V_88F6810_PLUS),
+ MPP_VAR_FUNCTION(6, "ua1", "txd", V_88F6810_PLUS)),
MPP_MODE(21,
MPP_VAR_FUNCTION(0, "gpio", NULL, V_88F6810_PLUS),
MPP_VAR_FUNCTION(1, "spi0", "cs1", V_88F6810_PLUS),
--
2.2.1

98
target/linux/mvebu/patches-3.19/024-ARM-mvebu-a38x-Fix-node-names.patch Normal file
View File

@ -0,0 +1,98 @@
From 4a25432b13090b57d257fa0ffb6712d8acf94523 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Thu, 8 Jan 2015 18:38:05 +0100
Subject: [PATCH 1/4] ARM: mvebu: a38x: Fix node names
Some nodes in the DTs have a reg property but no unit name in their node name.
This contradicts the way the ePAPR defines the node names. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/armada-380.dtsi | 2 +-
arch/arm/boot/dts/armada-385-db.dts | 2 +-
arch/arm/boot/dts/armada-385-rd.dts | 2 +-
arch/arm/boot/dts/armada-385.dtsi | 2 +-
arch/arm/boot/dts/armada-38x.dtsi | 4 ++--
5 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/armada-380.dtsi
index 4173a8ab34e7..13400ce88c54 100644
--- a/arch/arm/boot/dts/armada-380.dtsi
+++ b/arch/arm/boot/dts/armada-380.dtsi
@@ -32,7 +32,7 @@
soc {
internal-regs {
- pinctrl {
+ pinctrl@18000 {
compatible = "marvell,mv88f6810-pinctrl";
reg = <0x18000 0x20>;
};
diff --git a/arch/arm/boot/dts/armada-385-db.dts b/arch/arm/boot/dts/armada-385-db.dts
index 2aaa9d2ac284..212605ccc7b6 100644
--- a/arch/arm/boot/dts/armada-385-db.dts
+++ b/arch/arm/boot/dts/armada-385-db.dts
@@ -74,7 +74,7 @@
phy-mode = "rgmii-id";
};
- mdio {
+ mdio@72004 {
phy0: ethernet-phy@0 {
reg = <0>;
};
diff --git a/arch/arm/boot/dts/armada-385-rd.dts b/arch/arm/boot/dts/armada-385-rd.dts
index aaca2861dc87..74a3bfe6efd7 100644
--- a/arch/arm/boot/dts/armada-385-rd.dts
+++ b/arch/arm/boot/dts/armada-385-rd.dts
@@ -67,7 +67,7 @@
};
- mdio {
+ mdio@72004 {
phy0: ethernet-phy@0 {
reg = <0>;
};
diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi
index 6283d7912f71..5249a4d3c207 100644
--- a/arch/arm/boot/dts/armada-385.dtsi
+++ b/arch/arm/boot/dts/armada-385.dtsi
@@ -37,7 +37,7 @@
soc {
internal-regs {
- pinctrl {
+ pinctrl@18000 {
compatible = "marvell,mv88f6820-pinctrl";
reg = <0x18000 0x20>;
};
diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 74391dace9e7..ada1f206028b 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -193,7 +193,7 @@
status = "disabled";
};
- pinctrl {
+ pinctrl@18000 {
compatible = "marvell,mv88f6820-pinctrl";
reg = <0x18000 0x20>;
};
@@ -373,7 +373,7 @@
status = "disabled";
};
- mdio {
+ mdio@72004 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "marvell,orion-mdio";
--
2.2.1

39
target/linux/mvebu/patches-3.19/208-ARM-mvebu-385-ap-Add-partitions.patch Normal file
View File

@ -0,0 +1,39 @@
From 9861f93a59142a3131870df2521eb2deb73026d7 Mon Sep 17 00:00:00 2001
From: Maxime Ripard <maxime.ripard@free-electrons.com>
Date: Tue, 13 Jan 2015 11:14:09 +0100
Subject: [PATCH 2/2] ARM: mvebu: 385-ap: Add partitions
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
arch/arm/boot/dts/armada-385-db-ap.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts
index 02db04867d8f..2a58443e2504 100644
--- a/arch/arm/boot/dts/armada-385-db-ap.dts
+++ b/arch/arm/boot/dts/armada-385-db-ap.dts
@@ -134,6 +134,21 @@
marvell,nand-keep-config;
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
+
+ mtd0@00000000 {
+ label = "u-boot";
+ reg = <0x00000000 0x00800000>;
+ };
+
+ mtd1@00800000 {
+ label = "kernel";
+ reg = <0x00800000 0x00800000>;
+ };
+
+ mtd2@01000000 {
+ label = "ubi";
+ reg = <0x01000000 0x3f000000>;
+ };
};
};
--
2.2.1