openwrt/target/linux/brcm2708/patches-3.14/0013-Fixes-for-sdhci-bcm2708.patch

From 58a6eba44c8b8a13ff99a7696519437c0abeb3aa Mon Sep 17 00:00:00 2001
From: popcornmix <popcornmix@gmail.com>
Date: Tue, 8 May 2012 23:12:13 +0100
Subject: [PATCH 13/54] Fixes for sdhci-bcm2708

possible fix for sdcard missing status. Thank naren

sdcard patch improvements from naren

sdhci-bcm2708: speed up DMA sync

Experiments show that it doesn't really take that long to sync, so we
can reduce the poll interval slightly. Might improve performance a bit.

sdhci-bcm2708: remove custom clock handling

The custom clock handling code is redundant and buggy. The MMC/SDHCI
subsystem does a better job than it, so remove it for good.

sdhci-bcm2708: add additional quirks

Some additional quirks are needed for correct operation.
There's no SDHCI capabilities register documented, and it always reads
zero, so add SDHCI_QUIRK_MISSING_CAPS. Apparently
SDHCI_QUIRK_NO_HISPD_BIT is needed for many cards to work correctly in
high-speed mode, so add it as well.

sdhci-bcm2708: add allow_highspeed parameter

Add a parameter to disable high-speed mode for the few cards that
still might have problems. High-speed mode is enabled by default.

sdhci-bcm2708: assume 50 MHz eMMC clock

80 MHz clock isnt't suited well to be dividable to get SD clocks of 25
MHz (default mode) or 50 MHz (high speed mode). 50 MHz are perfect to
drive the SD interface at ideal frequencies.

Allow emmc clock to be specified as command line parameter

sdhci-bcm2708: raise DMA sync timeout

Commit d64b84c by accident reduced the maximum overall DMA sync
timeout. The maximum overall timeout was reduced from 100ms to 30ms,
which isn't enough for many cards. Increase it to 150ms, just to be
extra safe. According to commit 872a8ff in the MMC subsystem, some
cards require crazy long timeouts (3s), but as we're busy-waiting,
and shouldn't delay for such a long time, let's hope 150ms will be
enough for most cards.

Use ndelay rather than udelay. Thanks lb

Add sync_after_dma module parameter

sdhci-bcm2708: use extension FIFO to buffer DMA transfers

The additional FIFO might speed up transfers in some cases.

sdhci-bcm2708: use multiblock-type transfers for single blocks

There are issues with both single block reads (missed completion)
and writes (data loss in some cases!). Just don't do single block
transfers anymore, and treat them like multiblock transfers. This
adds a quirk for this and uses it.

Add module parameter for missing_status quirk. sdhci-bcm2708.missing_status=0 may improve interrupt latency

Fix spinlock recursion in sdhci-bcm2708.c

mmc: Report 3.3V support in caps

sdhci: Use macros for out spin lock/unlock functions to reduce diffs with upstream code

sdhci: sdhci_bcm2708_quirk_voltage_broken appears to be a no-op

sdhci: sdhci_bcm2708_uhs_broken should be handled through caps reported

Add low-latency mode to sdcard driver. Disable with sdhci-bcm2708.enable_llm=0. Thanks ddv2005.

Allow the number of cycles delay between sdcard peripheral writes to be specified on command line with sdhci-bcm2708.cycle_delay

Lazy CRC quirk: Implemented retrying mechanisms for SD SSR and SCR, disabled missing_status and spurious CRC ACMD51 quirks by default (should be fixed by the retrying-mechanishm)

mmc: suppress sdcard warnings we are happy about by default

sdhci-bcm2807: Increase sync_after_dma timeout

The current timeout is being hit with some cards that complete successfully with a longer timeout.
The timeout is not handled well, and is believed to be a code path that causes corruption.
872a8ff suggests that crappy cards can take up to 3 seconds to respond

remove suspend/resume

fix sign in sdhci_bcm2708_raw_writel wait calculation

The ns_wait variable is intended to hold a lower bound on the number of nanoseconds that have elapsed since the last sdhci register write. However, the actual calculation of it was incorrect, as the subtraction was inverted. This commit fixes the calculation.

Note that this correction has no bearing when running with the default cycle_delay of 2 and the default clock rate of 50 MHz, under which conditions ns_2clk is 40 nanoseconds and ns_wait, regardless of whether the subtraction is done correctly or incorrectly, cannot possibly be less than 40 except for during the one-microsecond period just before the tick counter wraps around to meet last_write_hpt (i.e., approximately 4295 seconds after the preceding sdhci register write). The correction in this commit only comes into play if ns_2clk > 1000, which requires a cycle_delay of 51 or greater when using the default clock rate. Under those conditions, sdhci_bcm2708_raw_writel will not wait for the full cycle_delay count if at least 1000 nanoseconds have elapsed since the last register write.

sdhci: Only do one iteration of PIO reading loop

Changed wording on logging. Previously, we received errors like this:
mmc0: could read SD Status register (SSR) at the 3th attempt
A more sensible response is now returned.
A typo also fixed in comments.
---
 drivers/mmc/card/block.c         |   2 +-
 drivers/mmc/core/sd.c            | 110 +++++++++++++++--
 drivers/mmc/host/sdhci-bcm2708.c | 254 ++++++++++++++++++---------------------
 drivers/mmc/host/sdhci.c         | 180 ++++++++++++++++++++-------
 drivers/mmc/host/sdhci.h         |   8 +-
 include/linux/mmc/host.h         |   1 +
 include/linux/mmc/sdhci.h        |   1 +
 7 files changed, 365 insertions(+), 191 deletions(-)

--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1361,7 +1361,7 @@ static void mmc_blk_rw_rq_prep(struct mm
 			brq->data.blocks = 1;
 	}
 
-	if (brq->data.blocks > 1 || do_rel_wr) {
+	if (brq->data.blocks > 1 || do_rel_wr || card->host->caps2 & MMC_CAP2_FORCE_MULTIBLOCK) {
 		/* SPI multiblock writes terminate using a special
 		 * token, not a STOP_TRANSMISSION request.
 		 */
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -15,6 +15,8 @@
 #include <linux/slab.h>
 #include <linux/stat.h>
 #include <linux/pm_runtime.h>
+#include <linux/jiffies.h>
+#include <linux/nmi.h>
 
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
@@ -67,6 +69,15 @@ static const unsigned int sd_au_size[] =
 		__res & __mask;						\
 	})
 
+// timeout for tries
+static const unsigned long retry_timeout_ms= 10*1000;
+
+// try at least 10 times, even if timeout is reached
+static const int retry_min_tries= 10;
+
+// delay between tries
+static const unsigned long retry_delay_ms= 10;
+
 /*
  * Given the decoded CSD structure, decode the raw CID to our CID structure.
  */
@@ -219,12 +230,63 @@ static int mmc_decode_scr(struct mmc_car
 }
 
 /*
- * Fetch and process SD Status register.
+ * Fetch and process SD Configuration Register.
+ */
+static int mmc_read_scr(struct mmc_card *card)
+{
+	unsigned long timeout_at;
+	int err, tries;
+
+	timeout_at= jiffies + msecs_to_jiffies( retry_timeout_ms );
+	tries= 		0;
+
+	while( tries < retry_min_tries || time_before( jiffies, timeout_at ) )
+	{
+		unsigned long delay_at;
+		tries++;
+
+		err = mmc_app_send_scr(card, card->raw_scr);
+		if( !err )
+			break; // success!!!
+
+		touch_nmi_watchdog();	  // we are still alive!
+
+		// delay
+		delay_at= jiffies + msecs_to_jiffies( retry_delay_ms );
+		while( time_before( jiffies, delay_at ) )
+		{
+			mdelay( 1 );
+			touch_nmi_watchdog();	  // we are still alive!
+		}
+	}
+
+	if( err)
+	{
+		pr_err("%s: failed to read SD Configuration register (SCR) after %d tries during %lu ms, error %d\n", mmc_hostname(card->host), tries, retry_timeout_ms, err );
+		return err;
+	}
+
+	if( tries > 1 )
+	{
+		pr_info("%s: could read SD Configuration register (SCR) at the %dth attempt\n", mmc_hostname(card->host), tries );
+	}
+
+	err = mmc_decode_scr(card);
+	if (err)
+		return err;
+
+	return err;
+}
+
+/*
+ * Fetch and process SD Status Register.
  */
 static int mmc_read_ssr(struct mmc_card *card)
 {
+	unsigned long timeout_at;
 	unsigned int au, es, et, eo;
 	int err, i;
+  int tries;
 	u32 *ssr;
 
 	if (!(card->csd.cmdclass & CCC_APP_SPEC)) {
@@ -237,14 +299,40 @@ static int mmc_read_ssr(struct mmc_card 
 	if (!ssr)
 		return -ENOMEM;
 
-	err = mmc_app_sd_status(card, ssr);
-	if (err) {
-		pr_warning("%s: problem reading SD Status "
-			"register.\n", mmc_hostname(card->host));
-		err = 0;
+	timeout_at= jiffies + msecs_to_jiffies( retry_timeout_ms );
+	tries= 		0;
+
+	while( tries < retry_min_tries || time_before( jiffies, timeout_at ) )
+	{
+		unsigned long delay_at;
+		tries++;
+
+		err= mmc_app_sd_status(card, ssr);
+		if( !err )
+			break; // sucess!!!
+
+		touch_nmi_watchdog();	  // we are still alive!
+
+		// delay
+		delay_at= jiffies + msecs_to_jiffies( retry_delay_ms );
+		while( time_before( jiffies, delay_at ) )
+		{
+			mdelay( 1 );
+			touch_nmi_watchdog();	  // we are still alive!
+		}
+	}
+
+	if( err)
+	{
+		pr_err("%s: failed to read SD Status register (SSR) after %d tries during %lu ms, error %d\n", mmc_hostname(card->host), tries, retry_timeout_ms, err );
 		goto out;
 	}
 
+	if( tries > 1 )
+	{
+		pr_info("%s: read SD Status register (SSR) after %d attempts\n", mmc_hostname(card->host), tries );
+	}
+
 	for (i = 0; i < 16; i++)
 		ssr[i] = be32_to_cpu(ssr[i]);
 
@@ -826,14 +914,10 @@ int mmc_sd_setup_card(struct mmc_host *h
 
 	if (!reinit) {
 		/*
-		 * Fetch SCR from card.
+		 * Fetch and decode SD Configuration register.
 		 */
-		err = mmc_app_send_scr(card, card->raw_scr);
-		if (err)
-			return err;
-
-		err = mmc_decode_scr(card);
-		if (err)
+		err = mmc_read_scr(card);
+		if( err )
 			return err;
 
 		/*
--- a/drivers/mmc/host/sdhci-bcm2708.c
+++ b/drivers/mmc/host/sdhci-bcm2708.c
@@ -51,7 +51,6 @@
 #undef CONFIG_MMC_SDHCI_BCM2708_DMA
 #define CONFIG_MMC_SDHCI_BCM2708_DMA y
 
-#define USE_SYNC_AFTER_DMA
 #ifdef CONFIG_MMC_SDHCI_BCM2708_DMA
 /* #define CHECK_DMA_USE */
 #endif
@@ -73,7 +72,12 @@
 #define BCM2708_SDHCI_SLEEP_TIMEOUT 1000   /* msecs */
 
 /* Mhz clock that the EMMC core is running at. Should match the platform clockman settings */
-#define BCM2708_EMMC_CLOCK_FREQ 80000000
+#define BCM2708_EMMC_CLOCK_FREQ 50000000
+
+#define REG_EXRDFIFO_EN     0x80
+#define REG_EXRDFIFO_CFG    0x84
+
+int cycle_delay=2;
 
 /*****************************************************************************\
  *									     *
@@ -129,6 +133,14 @@ static inline unsigned long int since_ns
 	return (unsigned long)((hptime() - t) * HPTIME_CLK_NS);
 }
 
+static bool allow_highspeed = 1;
+static int emmc_clock_freq = BCM2708_EMMC_CLOCK_FREQ;
+static bool sync_after_dma = 1;
+static bool missing_status = 1;
+static bool spurious_crc_acmd51 = 0;
+bool enable_llm = 1;
+bool extra_messages = 0;
+
 #if 0
 static void hptime_test(void)
 {
@@ -241,19 +253,19 @@ static void sdhci_bcm2708_raw_writel(str
 		/* host->clock is the clock freq in Hz */
 		static hptime_t last_write_hpt;
 		hptime_t now = hptime();
-		ns_2clk = 2000000000/host->clock;
+		ns_2clk = cycle_delay*1000000/(host->clock/1000);
 
 		if (now == last_write_hpt || now == last_write_hpt+1) {
 			 /* we can't guarantee any significant time has
 			  * passed - we'll have to wait anyway ! */
-			udelay((ns_2clk+1000-1)/1000);
+			ndelay(ns_2clk);
 		} else
 		{
 			/* we must have waited at least this many ns: */
 			unsigned int ns_wait = HPTIME_CLK_NS *
-					       (last_write_hpt - now - 1);
+					       (now - last_write_hpt - 1);
 			if (ns_wait < ns_2clk)
-				udelay((ns_2clk-ns_wait+500)/1000);
+				ndelay(ns_2clk - ns_wait);
 		}
 		last_write_hpt = now;
 	}
@@ -269,13 +281,13 @@ static void sdhci_bcm2708_raw_writel(str
 		ier &= ~SDHCI_INT_DATA_TIMEOUT;
 		writel(ier, host->ioaddr + SDHCI_SIGNAL_ENABLE);
 		timeout_disabled = true;
-		udelay((ns_2clk+1000-1)/1000);
+		ndelay(ns_2clk);
 	} else if (timeout_disabled) {
 		ier = readl(host->ioaddr + SDHCI_SIGNAL_ENABLE);
 		ier |= SDHCI_INT_DATA_TIMEOUT;
 		writel(ier, host->ioaddr + SDHCI_SIGNAL_ENABLE);
 		timeout_disabled = false;
-		udelay((ns_2clk+1000-1)/1000);
+		ndelay(ns_2clk);
 	}
 #endif
 	writel(val, host->ioaddr + reg);
@@ -353,68 +365,9 @@ void sdhci_bcm2708_writeb(struct sdhci_h
 
 static unsigned int sdhci_bcm2708_get_max_clock(struct sdhci_host *host)
 {
-	return 20000000;	// this value is in Hz (20MHz)
-}
-
-static unsigned int sdhci_bcm2708_get_timeout_clock(struct sdhci_host *host)
-{
-	if(host->clock)
-		return (host->clock / 1000);		// this value is in kHz (100MHz)
-	else
-		return (sdhci_bcm2708_get_max_clock(host) / 1000);
+	return emmc_clock_freq;
 }
 
-static void sdhci_bcm2708_set_clock(struct sdhci_host *host, unsigned int clock)
-{
-	int div = 0;
-	u16 clk = 0;
-	unsigned long timeout;
-
-        if (clock == host->clock)
-                return;
-
-        sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
-
-        if (clock == 0)
-                goto out;
-
-	if (BCM2708_EMMC_CLOCK_FREQ <= clock)
-		div = 1;
-	else {
-		for (div = 2; div < SDHCI_MAX_DIV_SPEC_300; div += 2) {
-			if ((BCM2708_EMMC_CLOCK_FREQ / div) <= clock)
-				break;
-		}
-	}
-
-        DBG( "desired SD clock: %d, actual: %d\n",
-                clock, BCM2708_EMMC_CLOCK_FREQ / div);
-
-	clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
-	clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
-		<< SDHCI_DIVIDER_HI_SHIFT;
-	clk |= SDHCI_CLOCK_INT_EN;
-
-	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
-
-        timeout = 20;
-        while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
-                        & SDHCI_CLOCK_INT_STABLE)) {
-                if (timeout == 0) {
-			printk(KERN_ERR "%s: Internal clock never "
-				"stabilised.\n", mmc_hostname(host->mmc));
-                        return;
-                }
-                timeout--;
-                mdelay(1);
-        }
-
-        clk |= SDHCI_CLOCK_CARD_EN;
-        sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
-out:
-        host->clock = clock;
- }
-
 /*****************************************************************************\
  *									     *
  * DMA Operation							     *
@@ -695,11 +648,11 @@ void
 sdhci_bcm2708_platdma_reset(struct sdhci_host *host, struct mmc_data *data)
 {
 	struct sdhci_bcm2708_priv *host_priv = SDHCI_HOST_PRIV(host);
-	unsigned long flags;
+//	unsigned long flags;
 
 	BUG_ON(NULL == host);
 
-	spin_lock_irqsave(&host->lock, flags);
+//	spin_lock_irqsave(&host->lock, flags);
 
 	if (host_priv->dma_wanted) {
 		if (NULL == data) {
@@ -720,13 +673,16 @@ sdhci_bcm2708_platdma_reset(struct sdhci
 			cs = readl(host_priv->dma_chan_base + BCM2708_DMA_CS);
 
 			if (!(BCM2708_DMA_ACTIVE & cs))
-				printk(KERN_INFO "%s: missed completion of "
+			{
+				if (extra_messages)
+					printk(KERN_INFO "%s: missed completion of "
 				       "cmd %d DMA (%d/%d [%d]/[%d]) - "
 				       "ignoring it\n",
 				       mmc_hostname(host->mmc),
 				       host->last_cmdop,
 				       host_priv->sg_done, sg_todo,
 				       host_priv->sg_ix+1, sg_len);
+			}
 			else
 				printk(KERN_INFO "%s: resetting ongoing cmd %d"
 				       "DMA before %d/%d [%d]/[%d] complete\n",
@@ -779,7 +735,7 @@ sdhci_bcm2708_platdma_reset(struct sdhci
 #endif
 	}
 
-	spin_unlock_irqrestore(&host->lock, flags);
+//	spin_unlock_irqrestore(&host->lock, flags);
 }
 
 
@@ -792,11 +748,11 @@ static void sdhci_bcm2708_dma_complete_i
 	int sg_len;
 	int sg_ix;
 	int sg_todo;
-	unsigned long flags;
+//	unsigned long flags;
 
 	BUG_ON(NULL == host);
 
-	spin_lock_irqsave(&host->lock, flags);
+//	spin_lock_irqsave(&host->lock, flags);
 	data = host->data;
 
 #ifdef CHECK_DMA_USE
@@ -821,7 +777,7 @@ static void sdhci_bcm2708_dma_complete_i
 
 	if (NULL == data) {
 		DBG("PDMA unused completion - status 0x%X\n", dma_cs);
-		spin_unlock_irqrestore(&host->lock, flags);
+//		spin_unlock_irqrestore(&host->lock, flags);
 		return;
 	}
 	sg = data->sg;
@@ -878,40 +834,34 @@ static void sdhci_bcm2708_dma_complete_i
 						SDHCI_INT_SPACE_AVAIL);
 		}
 	} else {
-#ifdef USE_SYNC_AFTER_DMA
-		/* On the Arasan controller the stop command (which will be
-		   scheduled after this completes) does not seem to work
-		   properly if we allow it to be issued when we are
-		   transferring data to/from the SD card.
-		   We get CRC and DEND errors unless we wait for
-		   the SD controller to finish reading/writing to the card. */
-		u32 state_mask;
-		int timeout=1000000;
-		hptime_t now = hptime();
+		if (sync_after_dma) {
+			/* On the Arasan controller the stop command (which will be
+			   scheduled after this completes) does not seem to work
+			   properly if we allow it to be issued when we are
+			   transferring data to/from the SD card.
+			   We get CRC and DEND errors unless we wait for
+			   the SD controller to finish reading/writing to the card. */
+			u32 state_mask;
+			int timeout=3*1000*1000;
 
-		DBG("PDMA over - sync card\n");
-		if (data->flags & MMC_DATA_READ)
-			state_mask = SDHCI_DOING_READ;
-		else
-			state_mask = SDHCI_DOING_WRITE;
+			DBG("PDMA over - sync card\n");
+			if (data->flags & MMC_DATA_READ)
+				state_mask = SDHCI_DOING_READ;
+			else
+				state_mask = SDHCI_DOING_WRITE;
 
-		while (0 != (sdhci_bcm2708_raw_readl(host,
-						     SDHCI_PRESENT_STATE) &
-			     state_mask) && --timeout > 0)
-			continue;
-
-		if (1000000-timeout > 4000) /*ave. is about 3250*/
-			DBG("%s: note - long %s sync %luns - "
-			       "%d its.\n",
-			       mmc_hostname(host->mmc),
-			       data->flags & MMC_DATA_READ? "read": "write",
-			       since_ns(now), 1000000-timeout);
-		if (timeout <= 0)
-			printk(KERN_ERR"%s: final %s to SD card still "
-			       "running\n",
-			       mmc_hostname(host->mmc),
-			       data->flags & MMC_DATA_READ? "read": "write");
-#endif
+			while (0 != (sdhci_bcm2708_raw_readl(host, SDHCI_PRESENT_STATE)
+				& state_mask) && --timeout > 0)
+			{
+				udelay(1);
+				continue;
+			}
+			if (timeout <= 0)
+				printk(KERN_ERR"%s: final %s to SD card still "
+				       "running\n",
+				       mmc_hostname(host->mmc),
+				       data->flags & MMC_DATA_READ? "read": "write");
+		}
 		if (host_priv->complete) {
 			(*host_priv->complete)(host);
 			DBG("PDMA %s complete\n",
@@ -920,7 +870,7 @@ static void sdhci_bcm2708_dma_complete_i
 						SDHCI_INT_SPACE_AVAIL);
 		}
 	}
-	spin_unlock_irqrestore(&host->lock, flags);
+//	spin_unlock_irqrestore(&host->lock, flags);
 }
 
 static irqreturn_t sdhci_bcm2708_dma_irq(int irq, void *dev_id)
@@ -929,12 +879,11 @@ static irqreturn_t sdhci_bcm2708_dma_irq
 	struct sdhci_host *host = dev_id;
 	struct sdhci_bcm2708_priv *host_priv = SDHCI_HOST_PRIV(host);
 	u32 dma_cs; /* control and status register */
-	unsigned long flags;
 
 	BUG_ON(NULL == dev_id);
 	BUG_ON(NULL == host_priv->dma_chan_base);
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock(host);
 
 	dma_cs = readl(host_priv->dma_chan_base + BCM2708_DMA_CS);
 
@@ -958,7 +907,8 @@ static irqreturn_t sdhci_bcm2708_dma_irq
 
 		if (!host_priv->dma_wanted) {
 			/* ignore this interrupt - it was reset */
-			printk(KERN_INFO "%s: DMA IRQ %X ignored - "
+			if (extra_messages)
+				printk(KERN_INFO "%s: DMA IRQ %X ignored - "
 			       "results were reset\n",
 			       mmc_hostname(host->mmc), dma_cs);
 #ifdef CHECK_DMA_USE
@@ -975,8 +925,7 @@ static irqreturn_t sdhci_bcm2708_dma_irq
 
 		result = IRQ_HANDLED;
 	}
-
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock(host);
 
 	return result;
 }
@@ -1019,10 +968,12 @@ static ssize_t attr_dma_store(struct dev
 		int on = simple_strtol(buf, NULL, 0);
 		if (on) {
 			host->flags |= SDHCI_USE_PLATDMA;
+			sdhci_bcm2708_writel(host, 1, REG_EXRDFIFO_EN);
 			printk(KERN_INFO "%s: DMA enabled\n",
 			       mmc_hostname(host->mmc));
 		} else {
 			host->flags &= ~(SDHCI_USE_PLATDMA | SDHCI_REQ_USE_DMA);
+			sdhci_bcm2708_writel(host, 0, REG_EXRDFIFO_EN);
 			printk(KERN_INFO "%s: DMA disabled\n",
 			       mmc_hostname(host->mmc));
 		}
@@ -1126,7 +1077,7 @@ static int sdhci_bcm2708_suspend(struct 
 	int ret = 0;
 
 	if (host->mmc) {
-		ret = mmc_suspend_host(host->mmc);
+		//ret = mmc_suspend_host(host->mmc);
 	}
 
 	return ret;
@@ -1139,7 +1090,7 @@ static int sdhci_bcm2708_resume(struct p
 	int ret = 0;
 
 	if (host->mmc) {
-		ret = mmc_resume_host(host->mmc);
+		//ret = mmc_resume_host(host->mmc);
 	}
 
 	return ret;
@@ -1158,19 +1109,14 @@ static unsigned int sdhci_bcm2708_quirk_
         return 1;
 }
 
-static unsigned int sdhci_bcm2708_quirk_spurious_crc(struct sdhci_host *host)
+static unsigned int sdhci_bcm2708_quirk_spurious_crc_acmd51(struct sdhci_host *host)
 {
         return 1;
 }
 
-static unsigned int sdhci_bcm2708_quirk_voltage_broken(struct sdhci_host *host)
+static unsigned int sdhci_bcm2708_missing_status(struct sdhci_host *host)
 {
-        return 1;
-}
-
-static unsigned int sdhci_bcm2708_uhs_broken(struct sdhci_host *host)
-{
-        return 1;
+	return 1;
 }
 
 /***************************************************************************** \
@@ -1190,11 +1136,7 @@ static struct sdhci_ops sdhci_bcm2708_op
 #else
 #error The BCM2708 SDHCI driver needs CONFIG_MMC_SDHCI_IO_ACCESSORS to be set
 #endif
-	//.enable_dma = NULL,
-	.set_clock = sdhci_bcm2708_set_clock,
 	.get_max_clock = sdhci_bcm2708_get_max_clock,
-	//.get_min_clock = NULL,
-	.get_timeout_clock = sdhci_bcm2708_get_timeout_clock,
 
 #ifdef CONFIG_MMC_SDHCI_BCM2708_DMA
 	// Platform DMA operations
@@ -1203,9 +1145,6 @@ static struct sdhci_ops sdhci_bcm2708_op
 	.pdma_reset = sdhci_bcm2708_platdma_reset,
 #endif
 	.extra_ints = sdhci_bcm2708_quirk_extra_ints,
-	.spurious_crc_acmd51 = sdhci_bcm2708_quirk_spurious_crc,
-	.voltage_broken = sdhci_bcm2708_quirk_voltage_broken,
-	.uhs_broken = sdhci_bcm2708_uhs_broken,
 };
 
 /*****************************************************************************\
@@ -1244,15 +1183,30 @@ static int sdhci_bcm2708_probe(struct pl
 		ret = PTR_ERR(host);
 		goto err;
 	}
+	if (missing_status) {
+		sdhci_bcm2708_ops.missing_status = sdhci_bcm2708_missing_status;
+	}
+
+	if( spurious_crc_acmd51 ) {
+		sdhci_bcm2708_ops.spurious_crc_acmd51 = sdhci_bcm2708_quirk_spurious_crc_acmd51;
+	}
+
+
+	printk("sdhci: %s low-latency mode\n",enable_llm?"Enable":"Disable");
 
 	host->hw_name = "BCM2708_Arasan";
 	host->ops = &sdhci_bcm2708_ops;
 	host->irq = platform_get_irq(pdev, 0);
+	host->second_irq = 0;
 
 	host->quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
 		       SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
 		       SDHCI_QUIRK_BROKEN_TIMEOUT_VAL |
-		       SDHCI_QUIRK_NONSTANDARD_CLOCK;
+               SDHCI_QUIRK_MISSING_CAPS |
+               SDHCI_QUIRK_NO_HISPD_BIT |
+               (sync_after_dma ? 0:SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12);
+
+
 #ifdef CONFIG_MMC_SDHCI_BCM2708_DMA
 	host->flags = SDHCI_USE_PLATDMA;
 #endif
@@ -1305,17 +1259,24 @@ static int sdhci_bcm2708_probe(struct pl
 	host_priv->dma_chan = ret;
 
 	ret = request_irq(host_priv->dma_irq, sdhci_bcm2708_dma_irq,
-			  IRQF_SHARED, DRIVER_NAME " (dma)", host);
+			  0 /*IRQF_SHARED*/, DRIVER_NAME " (dma)", host);
 	if (ret) {
 		dev_err(&pdev->dev, "cannot set DMA IRQ\n");
 		goto err_add_dma_irq;
 	}
+	host->second_irq = host_priv->dma_irq;
 	DBG("DMA CBs %p handle %08X DMA%d %p DMA IRQ %d\n",
 	    host_priv->cb_base, (unsigned)host_priv->cb_handle,
 	    host_priv->dma_chan, host_priv->dma_chan_base,
 	    host_priv->dma_irq);
 
-	host->mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
+    // we support 3.3V
+    host->caps |= SDHCI_CAN_VDD_330;
+    if (allow_highspeed)
+        host->mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
+
+    /* single block writes cause data loss with some SD cards! */
+    host->mmc->caps2 |= MMC_CAP2_FORCE_MULTIBLOCK;
 #endif
 
 	ret = sdhci_add_host(host);
@@ -1327,6 +1288,12 @@ static int sdhci_bcm2708_probe(struct pl
 	ret = device_create_file(&pdev->dev, &dev_attr_dma_wait);
 	ret = device_create_file(&pdev->dev, &dev_attr_status);
 
+#ifdef CONFIG_MMC_SDHCI_BCM2708_DMA
+	/* enable extension fifo for paced DMA transfers */
+	sdhci_bcm2708_writel(host, 1, REG_EXRDFIFO_EN);
+	sdhci_bcm2708_writel(host, 4, REG_EXRDFIFO_CFG);
+#endif
+
 	printk(KERN_INFO "%s: BCM2708 SDHC host at 0x%08llx DMA %d IRQ %d\n",
 	       mmc_hostname(host->mmc), (unsigned long long)iomem->start,
 	       host_priv->dma_chan, host_priv->dma_irq);
@@ -1418,7 +1385,26 @@ static void __exit sdhci_drv_exit(void)
 module_init(sdhci_drv_init);
 module_exit(sdhci_drv_exit);
 
+module_param(allow_highspeed, bool, 0444);
+module_param(emmc_clock_freq, int, 0444);
+module_param(sync_after_dma, bool, 0444);
+module_param(missing_status, bool, 0444);
+module_param(spurious_crc_acmd51, bool, 0444);
+module_param(enable_llm, bool, 0444);
+module_param(cycle_delay, int, 0444);
+module_param(extra_messages, bool, 0444);
+
 MODULE_DESCRIPTION("Secure Digital Host Controller Interface platform driver");
 MODULE_AUTHOR("Broadcom <info@broadcom.com>");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:"DRIVER_NAME);
+
+MODULE_PARM_DESC(allow_highspeed, "Allow high speed transfers modes");
+MODULE_PARM_DESC(emmc_clock_freq, "Specify the speed of emmc clock");
+MODULE_PARM_DESC(sync_after_dma, "Block in driver until dma complete");
+MODULE_PARM_DESC(missing_status, "Use the missing status quirk");
+MODULE_PARM_DESC(spurious_crc_acmd51, "Use the spurious crc quirk for reading SCR (ACMD51)");
+MODULE_PARM_DESC(enable_llm, "Enable low-latency mode");
+MODULE_PARM_DESC(extra_messages, "Enable more sdcard warning messages");
+
+
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -131,6 +131,99 @@ static void sdhci_dumpregs(struct sdhci_
  * Low level functions                                                       *
  *                                                                           *
 \*****************************************************************************/
+extern bool enable_llm;
+static int sdhci_locked=0;
+void sdhci_spin_lock(struct sdhci_host *host)
+{
+	spin_lock(&host->lock);
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		disable_irq_nosync(host->irq);
+		if(host->second_irq)
+			disable_irq_nosync(host->second_irq);
+		local_irq_enable();
+	}
+#endif
+}
+
+void sdhci_spin_unlock(struct sdhci_host *host)
+{
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		local_irq_disable();
+		if(host->second_irq)
+			enable_irq(host->second_irq);
+		enable_irq(host->irq);
+	}
+#endif
+	spin_unlock(&host->lock);
+}
+
+void sdhci_spin_lock_irqsave(struct sdhci_host *host,unsigned long *flags)
+{
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		while(sdhci_locked)
+		{
+			preempt_schedule();
+		}
+		spin_lock_irqsave(&host->lock,*flags);
+		disable_irq(host->irq);
+		if(host->second_irq)
+			disable_irq(host->second_irq);
+		local_irq_enable();
+	}
+	else
+#endif
+		spin_lock_irqsave(&host->lock,*flags);
+}
+
+void sdhci_spin_unlock_irqrestore(struct sdhci_host *host,unsigned long flags)
+{
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		local_irq_disable();
+		if(host->second_irq)
+			enable_irq(host->second_irq);
+		enable_irq(host->irq);
+	}
+#endif
+	spin_unlock_irqrestore(&host->lock,flags);
+}
+
+static void sdhci_spin_enable_schedule(struct sdhci_host *host)
+{
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		sdhci_locked = 1;
+		preempt_enable();
+	}
+#endif
+}
+
+static void sdhci_spin_disable_schedule(struct sdhci_host *host)
+{
+#ifdef CONFIG_PREEMPT
+	if(enable_llm)
+	{
+		preempt_disable();
+		sdhci_locked = 0;
+	}
+#endif
+}
+
+
+#undef spin_lock_irqsave
+#define spin_lock_irqsave(host_lock, flags)      sdhci_spin_lock_irqsave(container_of(host_lock, struct sdhci_host, lock), &flags)
+#define spin_unlock_irqrestore(host_lock, flags) sdhci_spin_unlock_irqrestore(container_of(host_lock, struct sdhci_host, lock), flags)
+
+#define spin_lock(host_lock)   sdhci_spin_lock(container_of(host_lock, struct sdhci_host, lock))
+#define spin_unlock(host_lock) sdhci_spin_unlock(container_of(host_lock, struct sdhci_host, lock))
 
 static void sdhci_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set)
 {
@@ -300,7 +393,7 @@ static void sdhci_led_control(struct led
 	struct sdhci_host *host = container_of(led, struct sdhci_host, led);
 	unsigned long flags;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	if (host->runtime_suspended)
 		goto out;
@@ -310,7 +403,7 @@ static void sdhci_led_control(struct led
 	else
 		sdhci_activate_led(host);
 out:
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 #endif
 
@@ -457,6 +550,7 @@ static void sdhci_transfer_pio(struct sd
 			break;
 		state = sdhci_readl(host, SDHCI_PRESENT_STATE);
 		available = state & mask;
+		break;
 	}
 
 	DBG("PIO transfer complete - %d blocks left.\n", host->blocks);
@@ -1023,7 +1117,9 @@ void sdhci_send_command(struct sdhci_hos
 			return;
 		}
 		timeout--;
+		sdhci_spin_enable_schedule(host);
 		mdelay(1);
+		sdhci_spin_disable_schedule(host);
 	}
 	DBG("send cmd %d - wait 0x%X irq 0x%x\n", cmd->opcode, mask,
 	    sdhci_readl(host, SDHCI_INT_STATUS));
@@ -1256,7 +1352,9 @@ clock_set:
 			return;
 		}
 		timeout--;
+		sdhci_spin_enable_schedule(host);
 		mdelay(1);
+		sdhci_spin_disable_schedule(host);
 	}
 
 	clk |= SDHCI_CLOCK_CARD_EN;
@@ -1357,7 +1455,7 @@ static void sdhci_request(struct mmc_hos
 
 	sdhci_runtime_pm_get(host);
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	WARN_ON(host->mrq != NULL);
 
@@ -1422,9 +1520,9 @@ static void sdhci_request(struct mmc_hos
 				 */
 				host->mrq = NULL;
 
-				spin_unlock_irqrestore(&host->lock, flags);
+				sdhci_spin_unlock_irqrestore(host, flags);
 				sdhci_execute_tuning(mmc, tuning_opcode);
-				spin_lock_irqsave(&host->lock, flags);
+				sdhci_spin_lock_irqsave(host, &flags);
 
 				/* Restore original mmc_request structure */
 				host->mrq = mrq;
@@ -1438,7 +1536,7 @@ static void sdhci_request(struct mmc_hos
 	}
 
 	mmiowb();
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
@@ -1447,10 +1545,10 @@ static void sdhci_do_set_ios(struct sdhc
 	int vdd_bit = -1;
 	u8 ctrl;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	if (host->flags & SDHCI_DEVICE_DEAD) {
-		spin_unlock_irqrestore(&host->lock, flags);
+		sdhci_spin_unlock_irqrestore(host, flags);
 		if (host->vmmc && ios->power_mode == MMC_POWER_OFF)
 			mmc_regulator_set_ocr(host->mmc, host->vmmc, 0);
 		return;
@@ -1478,9 +1576,9 @@ static void sdhci_do_set_ios(struct sdhc
 		vdd_bit = sdhci_set_power(host, ios->vdd);
 
 	if (host->vmmc && vdd_bit != -1) {
-		spin_unlock_irqrestore(&host->lock, flags);
+		sdhci_spin_unlock_irqrestore(host, flags);
 		mmc_regulator_set_ocr(host->mmc, host->vmmc, vdd_bit);
-		spin_lock_irqsave(&host->lock, flags);
+		sdhci_spin_lock_irqsave(host, &flags);
 	}
 
 	if (host->ops->platform_send_init_74_clocks)
@@ -1519,7 +1617,7 @@ static void sdhci_do_set_ios(struct sdhc
 	else
 		ctrl &= ~SDHCI_CTRL_HISPD;
 
-	if (host->version >= SDHCI_SPEC_300 && !(host->ops->uhs_broken)) {
+	if (host->version >= SDHCI_SPEC_300) {
 		u16 clk, ctrl_2;
 
 		/* In case of UHS-I modes, set High Speed Enable */
@@ -1617,7 +1715,7 @@ static void sdhci_do_set_ios(struct sdhc
 		sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 
 	mmiowb();
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
@@ -1665,7 +1763,7 @@ static int sdhci_check_ro(struct sdhci_h
 	unsigned long flags;
 	int is_readonly;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	if (host->flags & SDHCI_DEVICE_DEAD)
 		is_readonly = 0;
@@ -1675,7 +1773,7 @@ static int sdhci_check_ro(struct sdhci_h
 		is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
 				& SDHCI_WRITE_PROTECT);
 
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 
 	/* This quirk needs to be replaced by a callback-function later */
 	return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
@@ -1748,9 +1846,9 @@ static void sdhci_enable_sdio_irq(struct
 	struct sdhci_host *host = mmc_priv(mmc);
 	unsigned long flags;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 	sdhci_enable_sdio_irq_nolock(host, enable);
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
@@ -2101,7 +2199,7 @@ static void sdhci_card_event(struct mmc_
 	if (host->ops->card_event)
 		host->ops->card_event(host);
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	/* Check host->mrq first in case we are runtime suspended */
 	if (host->mrq && !sdhci_do_get_cd(host)) {
@@ -2117,7 +2215,7 @@ static void sdhci_card_event(struct mmc_
 		tasklet_schedule(&host->finish_tasklet);
 	}
 
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 static const struct mmc_host_ops sdhci_ops = {
@@ -2156,14 +2254,14 @@ static void sdhci_tasklet_finish(unsigne
 
 	host = (struct sdhci_host*)param;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
         /*
          * If this tasklet gets rescheduled while running, it will
          * be run again afterwards but without any active request.
          */
 	if (!host->mrq) {
-		spin_unlock_irqrestore(&host->lock, flags);
+		sdhci_spin_unlock_irqrestore(host, flags);
 		return;
 	}
 
@@ -2201,7 +2299,7 @@ static void sdhci_tasklet_finish(unsigne
 #endif
 
 	mmiowb();
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 
 	mmc_request_done(host->mmc, mrq);
 	sdhci_runtime_pm_put(host);
@@ -2214,7 +2312,7 @@ static void sdhci_timeout_timer(unsigned
 
 	host = (struct sdhci_host*)data;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	if (host->mrq) {
 		pr_err("%s: Timeout waiting for hardware "
@@ -2235,7 +2333,7 @@ static void sdhci_timeout_timer(unsigned
 	}
 
 	mmiowb();
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 static void sdhci_tuning_timer(unsigned long data)
@@ -2245,11 +2343,11 @@ static void sdhci_tuning_timer(unsigned 
 
 	host = (struct sdhci_host *)data;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	host->flags |= SDHCI_NEEDS_RETUNING;
 
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 }
 
 /*****************************************************************************\
@@ -2473,10 +2571,10 @@ static irqreturn_t sdhci_irq(int irq, vo
 	u32 intmask, unexpected = 0;
 	int cardint = 0, max_loops = 16;
 
-	spin_lock(&host->lock);
+	sdhci_spin_lock(host);
 
 	if (host->runtime_suspended) {
-		spin_unlock(&host->lock);
+		sdhci_spin_unlock(host);
 		pr_warning("%s: got irq while runtime suspended\n",
 		       mmc_hostname(host->mmc));
 		return IRQ_HANDLED;
@@ -2588,7 +2686,7 @@ again:
 	if (intmask && --max_loops)
 		goto again;
 out:
-	spin_unlock(&host->lock);
+	sdhci_spin_unlock(host);
 
 	if (unexpected) {
 		pr_err("%s: Unexpected interrupt 0x%08x.\n",
@@ -2674,7 +2772,7 @@ int sdhci_resume_host(struct sdhci_host 
 	}
 
 	if (!device_may_wakeup(mmc_dev(host->mmc))) {
-		ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
+		ret = request_irq(host->irq, sdhci_irq, 0 /*IRQF_SHARED*/,
 				  mmc_hostname(host->mmc), host);
 		if (ret)
 			return ret;
@@ -2750,15 +2848,15 @@ int sdhci_runtime_suspend_host(struct sd
 		host->flags &= ~SDHCI_NEEDS_RETUNING;
 	}
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 	sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 
 	synchronize_irq(host->irq);
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 	host->runtime_suspended = true;
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 
 	return ret;
 }
@@ -2784,16 +2882,16 @@ int sdhci_runtime_resume_host(struct sdh
 	sdhci_do_start_signal_voltage_switch(host, &host->mmc->ios);
 	if ((host_flags & SDHCI_PV_ENABLED) &&
 		!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
-		spin_lock_irqsave(&host->lock, flags);
+		sdhci_spin_lock_irqsave(host, &flags);
 		sdhci_enable_preset_value(host, true);
-		spin_unlock_irqrestore(&host->lock, flags);
+		sdhci_spin_unlock_irqrestore(host, flags);
 	}
 
 	/* Set the re-tuning expiration flag */
 	if (host->flags & SDHCI_USING_RETUNING_TIMER)
 		host->flags |= SDHCI_NEEDS_RETUNING;
 
-	spin_lock_irqsave(&host->lock, flags);
+	sdhci_spin_lock_irqsave(host, &flags);
 
 	host->runtime_suspended = false;
 
@@ -2804,7 +2902,7 @@ int sdhci_runtime_resume_host(struct sdh
 	/* Enable Card Detection */
 	sdhci_enable_card_detection(host);
 
-	spin_unlock_irqrestore(&host->lock, flags);
+	sdhci_spin_unlock_irqrestore(host, flags);
 
 	return ret;
 }
@@ -3300,8 +3398,8 @@ int sdhci_add_host(struct sdhci_host *ho
 
 	sdhci_init(host, 0);
 
-	ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
-		mmc_hostname(mmc), host);
+	ret = request_irq(host->irq, sdhci_irq, 0 /*IRQF_SHARED*/,
+                mmc_hostname(mmc), host);
 	if (ret) {
 		pr_err("%s: Failed to request IRQ %d: %d\n",
 		       mmc_hostname(mmc), host->irq, ret);
@@ -3362,7 +3460,7 @@ void sdhci_remove_host(struct sdhci_host
 	unsigned long flags;
 
 	if (dead) {
-		spin_lock_irqsave(&host->lock, flags);
+		sdhci_spin_lock_irqsave(host, &flags);
 
 		host->flags |= SDHCI_DEVICE_DEAD;
 
@@ -3374,7 +3472,7 @@ void sdhci_remove_host(struct sdhci_host
 			tasklet_schedule(&host->finish_tasklet);
 		}
 
-		spin_unlock_irqrestore(&host->lock, flags);
+		sdhci_spin_unlock_irqrestore(host, flags);
 	}
 
 	sdhci_disable_card_detection(host);
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -300,8 +300,6 @@ struct sdhci_ops {
 				      struct mmc_data *data);
 	unsigned int 	(*extra_ints)(struct sdhci_host *host);
 	unsigned int	(*spurious_crc_acmd51)(struct sdhci_host *host);
-	unsigned int	(*voltage_broken)(struct sdhci_host *host);
-	unsigned int	(*uhs_broken)(struct sdhci_host *host);
 	unsigned int	(*missing_status)(struct sdhci_host *host);
 
 	void	(*hw_reset)(struct sdhci_host *host);
@@ -445,4 +443,10 @@ extern int sdhci_runtime_suspend_host(st
 extern int sdhci_runtime_resume_host(struct sdhci_host *host);
 #endif
 
+extern void sdhci_spin_lock_irqsave(struct sdhci_host *host,unsigned long *flags);
+extern void sdhci_spin_unlock_irqrestore(struct sdhci_host *host,unsigned long flags);
+extern void sdhci_spin_lock(struct sdhci_host *host);
+extern void sdhci_spin_unlock(struct sdhci_host *host);
+
+
 #endif /* __SDHCI_HW_H */
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -282,6 +282,7 @@ struct mmc_host {
 				 MMC_CAP2_PACKED_WR)
 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14)	/* Don't power up before scan */
 #define MMC_CAP2_SANITIZE	(1 << 15)		/* Support Sanitize */
+#define MMC_CAP2_FORCE_MULTIBLOCK (1 << 31)	/* Always use multiblock transfers */
 
 	mmc_pm_flag_t		pm_caps;	/* supported pm features */
 
--- a/include/linux/mmc/sdhci.h
+++ b/include/linux/mmc/sdhci.h
@@ -102,6 +102,7 @@ struct sdhci_host {
 #define SDHCI_QUIRK2_BROKEN_HS200			(1<<6)
 
 	int irq;		/* Device IRQ */
+	int second_irq; 	/* Additional IRQ to disable/enable in low-latency mode */
 	void __iomem *ioaddr;	/* Mapped address */
 
 	const struct sdhci_ops *ops;	/* Low level hw interface */