mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-01-04 13:42:24 +00:00
f574b535eb
Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
166 lines
6.2 KiB
Makefile
166 lines
6.2 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
|
|
PKG_SOURCE_PROTO:=git
|
|
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
|
|
PKG_SOURCE_DATE:=2023-03-18
|
|
PKG_SOURCE_VERSION:=86180c4c07330e303edf0afd6c017932903ee080
|
|
PKG_MIRROR_HASH:=283d6651f8a9088981065d476c01c7c0794279e108a96377468d5fcdc3882a12
|
|
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
8dev_habanero \
|
|
8dev_jalapeno \
|
|
aruba_ap-365 \
|
|
buffalo_wxr-5950ax12 \
|
|
devolo_magic-2-wifi-next \
|
|
dynalink_dl-wrx36 \
|
|
edgecore_eap102 \
|
|
edgecore_ecw5410 \
|
|
edgecore_oap100 \
|
|
edimax_cax1800 \
|
|
extreme-networks_ws-ap3915i \
|
|
glinet_gl-a1300 \
|
|
glinet_gl-ap1300 \
|
|
glinet_gl-s1300 \
|
|
linksys_ea8300 \
|
|
linksys_whw03v2 \
|
|
nokia_ac400i \
|
|
p2w_r619ac \
|
|
pakedge_wr-1 \
|
|
qnap_301w \
|
|
qxwlan_e2600ac-c1 \
|
|
qxwlan_e2600ac-c2 \
|
|
redmi_ax6 \
|
|
sony_ncp-hg100-cellular \
|
|
teltonika_rutx \
|
|
xiaomi_ax3600 \
|
|
xiaomi_ax9000 \
|
|
zte_mf18a \
|
|
zte_mf289f \
|
|
zyxel_nbg7815
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_ipq807x)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-ath11-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
)))))))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard $(PKG_BUILD_DIR)/board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# Add board name to ALLWIFIBOARDS
|
|
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
|
|
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
|
|
$(eval $(call generate-ipq-wifi-package,8dev_habanero,8devices Habanero))
|
|
$(eval $(call generate-ipq-wifi-package,8dev_jalapeno,8devices Jalapeno))
|
|
$(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
|
|
$(eval $(call generate-ipq-wifi-package,buffalo_wxr-5950ax12,Buffalo WXR-5950AX12))
|
|
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
|
|
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
|
|
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
|
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2))
|
|
$(eval $(call generate-ipq-wifi-package,nokia_ac400i,Nokia AC400i))
|
|
$(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
|
|
$(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1))
|
|
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
|
|
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
|
$(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
|
|
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
|
|
$(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|