openwrt/target/linux/realtek/dts/rtl8382_allnet_all-sg8208m.dts
Bjørn Mork 11d24ffe96 realtek: allow writing to "u-boot-env2"
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-08 09:20:59 +02:00

147 lines
2.4 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later
#include "rtl838x.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "allnet,all-sg8208m", "realtek,rtl838x-soc";
model = "ALLNET ALL-SG8208M";
aliases {
led-boot = &led_sys;
led-failsafe = &led_sys;
led-running = &led_sys;
led-upgrade = &led_sys;
};
chosen {
bootargs = "console=ttyS0,115200";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x8000000>;
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio0 67 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_sys: sys {
label = "green:sys";
gpios = <&gpio0 47 GPIO_ACTIVE_HIGH>;
};
// GPIO 25: power on/off all port leds
};
};
&gpio0 {
indirect-access-bus-id = <0>;
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "u-boot-env";
reg = <0x80000 0x10000>;
read-only;
};
partition@90000 {
label = "u-boot-env2";
reg = <0x90000 0x10000>;
};
partition@a0000 {
label = "jffs";
reg = <0xa0000 0x100000>;
};
partition@1a0000 {
label = "jffs2";
reg = <0x1a0000 0x100000>;
};
partition@2a0000 {
label = "firmware";
reg = <0x2a0000 0xd60000>;
compatible = "openwrt,uimage", "denx,uimage";
openwrt,ih-magic = <0x00000006>;
};
};
};
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
INTERNAL_PHY(8)
INTERNAL_PHY(9)
INTERNAL_PHY(10)
INTERNAL_PHY(11)
INTERNAL_PHY(12)
INTERNAL_PHY(13)
INTERNAL_PHY(14)
INTERNAL_PHY(15)
};
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
SWITCH_PORT(8, 1, internal)
SWITCH_PORT(9, 2, internal)
SWITCH_PORT(10, 3, internal)
SWITCH_PORT(11, 4, internal)
SWITCH_PORT(12, 5, internal)
SWITCH_PORT(13, 6, internal)
SWITCH_PORT(14, 7, internal)
SWITCH_PORT(15, 8, internal)
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};