mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-12 09:54:53 +00:00
7e614820a8
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
56 lines
1.4 KiB
Plaintext
56 lines
1.4 KiB
Plaintext
CONFIG_ARCH_HAS_TICK_BROADCAST=y
|
|
CONFIG_AT803X_PHY=y
|
|
CONFIG_BROADCOM_PHY=y
|
|
CONFIG_CMDLINE_OVERRIDE=y
|
|
CONFIG_CPU_RMAP=y
|
|
CONFIG_EEPROM_LEGACY=y
|
|
# CONFIG_FSL_CORENET_CF is not set
|
|
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
|
|
CONFIG_GENERIC_TBSYNC=y
|
|
CONFIG_GPIO_74X164=y
|
|
# CONFIG_GPIO_MAX77620 is not set
|
|
CONFIG_HAVE_RCU_TABLE_FREE=y
|
|
CONFIG_HIVEAP_330=y
|
|
CONFIG_PANDA=y
|
|
CONFIG_I2C_CHARDEV=y
|
|
CONFIG_LEDS_LP5521=y
|
|
CONFIG_LEDS_LP55XX_COMMON=y
|
|
CONFIG_LOCK_SPIN_ON_OWNER=y
|
|
# CONFIG_MAX77620_THERMAL is not set
|
|
# CONFIG_MAX77620_WATCHDOG is not set
|
|
CONFIG_MFD_CORE=y
|
|
CONFIG_MFD_MAX77620=y
|
|
CONFIG_MTD_CFI=y
|
|
CONFIG_MTD_NAND_FSL_ELBC=y
|
|
CONFIG_MTD_PHYSMAP=y
|
|
CONFIG_MTD_SPLIT_FIRMWARE=y
|
|
CONFIG_MTD_SPLIT_FIT_FW=y
|
|
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
|
CONFIG_MTD_UBI=y
|
|
CONFIG_MTD_UBI_BEB_LIMIT=20
|
|
CONFIG_MTD_UBI_BLOCK=y
|
|
CONFIG_MTD_UBI_WL_THRESHOLD=4096
|
|
CONFIG_MUTEX_SPIN_ON_OWNER=y
|
|
CONFIG_NET_FLOW_LIMIT=y
|
|
CONFIG_NR_CPUS=2
|
|
CONFIG_PADATA=y
|
|
CONFIG_REGMAP_IRQ=y
|
|
CONFIG_REGULATOR=y
|
|
CONFIG_RFS_ACCEL=y
|
|
CONFIG_RPS=y
|
|
# CONFIG_RTC_DRV_MAX77686 is not set
|
|
CONFIG_RWSEM_SPIN_ON_OWNER=y
|
|
CONFIG_SMP=y
|
|
CONFIG_SPI_GPIO=y
|
|
CONFIG_SWCONFIG_B53=y
|
|
# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set
|
|
CONFIG_SWCONFIG_B53_PHY_DRIVER=y
|
|
# CONFIG_SWCONFIG_B53_PHY_FIXUP is not set
|
|
# CONFIG_SWCONFIG_B53_SPI_DRIVER is not set
|
|
# CONFIG_SWCONFIG_B53_SRAB_DRIVER is not set
|
|
CONFIG_TREE_RCU=y
|
|
CONFIG_UBIFS_FS=y
|
|
CONFIG_WS_AP3710I=y
|
|
CONFIG_WS_AP3825I=y
|
|
CONFIG_XPS=y
|