mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-24 07:33:04 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
166 lines
2.5 KiB
Plaintext
166 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "OCEDO Raccoon";
|
|
compatible = "ocedo,raccoon", "qca,ar9344";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "green:power";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "yellow:wlan24";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
led_system: system {
|
|
label = "blue:sys";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan5g {
|
|
label = "red:wlan5";
|
|
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x740000>;
|
|
};
|
|
|
|
partition@790000 {
|
|
label = "vendor";
|
|
reg = <0x790000 0x740000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@ed0000 {
|
|
label = "data";
|
|
reg = <0xed0000 0x110000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "id";
|
|
reg = <0xfe0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k: wifi@0,0 {
|
|
compatible = "pci168c,0030";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mtd-mac-address = <&art 0xc>;
|
|
qca,no-eeprom;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x6>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x06000000 0x00000101 0x00001313>;
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
phy-mode = "rgmii-id";
|
|
phy-handle = <&phy0>;
|
|
};
|