openwrt/package/firmware/ipq-wifi
Dongming Han b9389186b0 ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-12-25 10:38:13 +01:00
..
board-8dev_habanero-dvk.qca4019
board-aruba_ap-303.qca4019
board-avm_fritzrepeater-1200.qca4019
board-buffalo_wtr-m2133hp.qca4019 ipq40xx: add support for Buffalo WTR-M2133HP 2020-07-08 16:07:05 +02:00
board-buffalo_wtr-m2133hp.qca9984 ipq40xx: add support for Buffalo WTR-M2133HP 2020-07-08 16:07:05 +02:00
board-cellc_rtl30vw.qca4019
board-devolo_magic-2-wifi-next.qca4019 ipq40xx: add support for devolo Magic 2 WiFi next 2020-12-22 20:55:40 +01:00
board-dlink_dap2610.qca4019
board-edgecore_ecw5410.qca9984 ipq806x: add Edgecore ECW5410 support 2020-09-17 08:42:17 +02:00
board-edgecore_oap100.qca4019 ipq40xx: add Edgecore OAP-100 support 2020-09-17 08:43:07 +02:00
board-engenius_eap2200.qca4019
board-engenius_eap2200.qca9888
board-engenius_emd1.qca4019
board-engenius_emr3500.qca4019
board-ezviz_cs-w3-wd1200g-eup.qca4019
board-glinet_gl-ap1300.qca4019 ipq40xx: add support for GL.iNet GL-AP1300 2020-12-25 10:38:13 +01:00
board-glinet_gl-s1300.qca4019
board-linksys_ea8300.qca4019
board-linksys_ea8300.qca9888
board-linksys_mr8300-v0.qca4019 ipq40xx: Add support for Linksys MR8300 (Dallas) 2020-09-25 19:31:51 +02:00
board-linksys_mr8300-v0.qca9888 ipq40xx: Add support for Linksys MR8300 (Dallas) 2020-09-25 19:31:51 +02:00
board-luma_wrtq-329acn.qca4019 ipq40xx: add support for Luma Home WRTQ-329ACN 2020-09-25 19:30:19 +02:00
board-mobipromo_cm520-79f.qca4019
board-nec_wg2600hp3.qca9984 ipq806x: add support for NEC Platforms Aterm WG2600HP3 2020-12-25 10:38:13 +01:00
board-plasmacloud_pa1200.qca4019 ipq-wifi: Fix suffix for Plasma Cloud PA1200 QCA4019 board-2.bin 2020-12-25 10:38:13 +01:00
board-plasmacloud_pa2200.qca4019 ipq-wifi: Fix suffix for Plasma Cloud PA2200 QCA4019 board-2.bin 2020-12-25 10:38:13 +01:00
board-plasmacloud_pa2200.qca9888 ipq40xx: add support for Plasma Cloud PA2200 2020-12-22 19:11:50 +01:00
board-qxwlan_e2600ac.qca4019
Makefile ipq40xx: add support for GL.iNet GL-AP1300 2020-12-25 10:38:13 +01:00