mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-24 15:43:25 +00:00
700c47a5f6
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
1180 lines
34 KiB
Makefile
1180 lines
34 KiB
Makefile
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
|
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
|
|
|
|
define Device/FitImage
|
|
KERNEL_SUFFIX := -uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitImageLzma
|
|
KERNEL_SUFFIX := -uImage.itb
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitzImage
|
|
KERNEL_SUFFIX := -zImage.itb
|
|
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := zImage
|
|
endef
|
|
|
|
define Device/UbiFit
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := factory.ubi sysupgrade.bin
|
|
IMAGE/factory.ubi := append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/DniImage
|
|
$(call Device/FitzImage)
|
|
NETGEAR_BOARD_ID :=
|
|
NETGEAR_HW_ID :=
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
endef
|
|
|
|
define Build/append-rootfshdr
|
|
mkimage -A $(LINUX_KARCH) \
|
|
-O linux -T filesystem \
|
|
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
|
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
|
|
cat $(IMAGE_KERNEL) > $@.$1
|
|
dd if=$@.new bs=64 count=1 >> $@.$1
|
|
endef
|
|
|
|
define Build/append-rutx-metadata
|
|
echo \
|
|
'{ \
|
|
"device_code": [".*"], \
|
|
"hwver": [".*"], \
|
|
"batch": [".*"], \
|
|
"serial": [".*"], \
|
|
"supported_devices":["teltonika,rutx"] \
|
|
}' | fwtool -I - $@
|
|
endef
|
|
|
|
define Build/copy-file
|
|
cat "$(1)" > "$@"
|
|
endef
|
|
|
|
define Build/mkmylofw_32m
|
|
$(eval device_id=$(word 1,$(1)))
|
|
$(eval revision=$(word 2,$(1)))
|
|
|
|
let \
|
|
size="$$(stat -c%s $@)" \
|
|
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
|
pad="(pad - (size % pad)) % pad" \
|
|
newsize='size + pad'; \
|
|
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
|
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
|
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
|
|
$@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/wac5xx-netgear-tar
|
|
mkdir $@.tmp
|
|
mv $@ $@.tmp/wac5xx-ubifs-root.img
|
|
md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum
|
|
echo "WAC505 WAC510" > $@.tmp/metadata.txt
|
|
echo "WAC505_V9.9.9.9" > $@.tmp/version
|
|
tar -C $@.tmp/ -cf $@ .
|
|
rm -rf $@.tmp
|
|
endef
|
|
|
|
define Build/qsdk-ipq-factory-nand-askey
|
|
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
|
|
askey_kernel $@.$1 \
|
|
askey_fs $(IMAGE_ROOTFS) \
|
|
ubifs $@
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/qsdk-ipq-app-gpt
|
|
cp $@ $@.tmp 2>/dev/null || true
|
|
ptgen -g -o $@.tmp -a 1 -l 1024 \
|
|
-t 0x2e -N 0:HLOS -r -p 32M \
|
|
-t 0x83 -N rootfs -r -p 128M \
|
|
-N rootfs_data -p 512M
|
|
cat $@.tmp >> $@
|
|
rm $@.tmp
|
|
endef
|
|
|
|
define Build/SenaoFW
|
|
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
|
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
|
-e $@ \
|
|
-o $@.new
|
|
@cp $@.new $@
|
|
endef
|
|
|
|
define Build/wrgg-image
|
|
mkwrggimg -i $@ \
|
|
-o $@.new \
|
|
-d "$(WRGG_DEVNAME)" \
|
|
-s "$(WRGG_SIGNATURE)" \
|
|
-v "" -m "" -B ""
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/8dev_habanero-dvk
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Habanero DVK
|
|
IMAGE_SIZE := 30976k
|
|
SOC := qcom-ipq4019
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += 8dev_habanero-dvk
|
|
|
|
define Device/8dev_jalapeno-common
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
SOC := qcom-ipq4018
|
|
endef
|
|
|
|
define Device/8dev_jalapeno
|
|
$(call Device/8dev_jalapeno-common)
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Jalapeno
|
|
endef
|
|
TARGET_DEVICES += 8dev_jalapeno
|
|
|
|
define Device/alfa-network_ap120c-ac
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP120C-AC
|
|
SOC := qcom-ipq4018
|
|
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 65536k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap120c-ac
|
|
|
|
define Device/aruba_glenmorangie
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Aruba
|
|
SOC := qcom-ipq4029
|
|
endef
|
|
|
|
define Device/aruba_ap-303
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-303
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-303
|
|
|
|
define Device/aruba_ap-303h
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-303H
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-303h
|
|
|
|
define Device/aruba_ap-365
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-365
|
|
DEVICE_PACKAGES := kmod-hwmon-ad7418 ipq-wifi-aruba_ap-365
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += aruba_ap-365
|
|
|
|
define Device/asus_map-ac2200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := Lyra (MAP-AC2200)
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
|
|
endef
|
|
TARGET_DEVICES += asus_map-ac2200
|
|
|
|
# WARNING: this is an initramfs image that gets you half of the way there
|
|
# you need to delete the jffs2 ubi volume and sysupgrade to the final image
|
|
# to get a "trx" you can flash via web UI for ac42u/ac58u:
|
|
# - change call Device/FitImageLzma to Device/FitImage
|
|
# - add the following below UIMAGE_NAME
|
|
# UIMAGE_MAGIC := 0x27051956
|
|
# IMAGES += factory.trx
|
|
# IMAGE/factory.trx := copy-file $(KDIR)/tmp/$$(KERNEL_INITRAMFS_IMAGE) | uImage none
|
|
define Device/asus_rt-ac42u
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC42U
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
DEVICE_ALT0_MODEL := RT-ACRH17
|
|
DEVICE_ALT1_VENDOR := ASUS
|
|
DEVICE_ALT1_MODEL := RT-AC2200
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20439364
|
|
FILESYSTEMS := squashfs
|
|
# RT-AC82U is nowhere to be found online
|
|
# Rather, this device is a/k/a RT-AC42U
|
|
# But we'll go with what the vendor firmware has...
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac42u
|
|
|
|
define Device/asus_rt-ac58u
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC58U
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
DEVICE_ALT0_MODEL := RT-ACRH13
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20439364
|
|
FILESYSTEMS := squashfs
|
|
# Someone - in their infinite wisdom - decided to put the firmware
|
|
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
|
# Since u-boot works with strings we either need another fixup step
|
|
# to add a version... or we are very careful not to add '\0' into that
|
|
# string and call it a day.... Yeah, we do the latter!
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac58u
|
|
|
|
define Device/avm_fritzbox-4040
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Box 4040
|
|
SOC := qcom-ipq4018
|
|
BOARD_NAME := fritz4040
|
|
IMAGE_SIZE := 29056k
|
|
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
|
UBOOT_PARTITION_SIZE := 524288
|
|
IMAGES += eva.bin
|
|
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
|
endef
|
|
TARGET_DEVICES += avm_fritzbox-4040
|
|
|
|
define Device/avm_fritzbox-7530
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Box 7530
|
|
DEVICE_ALT0_VENDOR := AVM
|
|
DEVICE_ALT0_MODEL := FRITZ!Box 7520
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
|
endef
|
|
TARGET_DEVICES += avm_fritzbox-7530
|
|
|
|
define Device/avm_fritzrepeater-1200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Repeater 1200
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
|
endef
|
|
TARGET_DEVICES += avm_fritzrepeater-1200
|
|
|
|
define Device/avm_fritzrepeater-3000
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Repeater 3000
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += avm_fritzrepeater-3000
|
|
|
|
define Device/buffalo_wtr-m2133hp
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WTR-M2133HP
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += buffalo_wtr-m2133hp
|
|
|
|
define Device/cellc_rtl30vw
|
|
KERNEL_SUFFIX := -zImage.itb
|
|
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
|
|
KERNEL_NAME := zImage
|
|
KERNEL_IN_UBI :=
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-rootfshdr kernel | append-ubi | qsdk-ipq-factory-nand-askey kernel
|
|
IMAGE/sysupgrade.bin := append-rootfshdr kernel | sysupgrade-tar kernel=$$$$@.kernel | append-metadata
|
|
DEVICE_VENDOR := Cell C
|
|
DEVICE_MODEL := RTL30VW
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@5
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 57344k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += cellc_rtl30vw
|
|
|
|
define Device/cilab_meshpoint-one
|
|
$(call Device/8dev_jalapeno-common)
|
|
DEVICE_VENDOR := Crisis Innovation Lab
|
|
DEVICE_MODEL := MeshPoint.One
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += cilab_meshpoint-one
|
|
|
|
define Device/compex_wpj419
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ419
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@12
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += compex_wpj419
|
|
|
|
define Device/compex_wpj428
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ428
|
|
SOC := qcom-ipq4028
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 31232k
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += cpximg-6a04.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
|
DEFAULT := n
|
|
endef
|
|
TARGET_DEVICES += compex_wpj428
|
|
|
|
define Device/devolo_magic-2-wifi-next
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := Magic 2 WiFi next
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 4096k
|
|
|
|
# If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image
|
|
# it will bootm it, just like we want for the initramfs.
|
|
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to 64k |\
|
|
append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00'
|
|
|
|
IMAGE_SIZE := 26624k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-devolo_magic-2-wifi-next
|
|
DEFAULT := n
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += devolo_magic-2-wifi-next
|
|
|
|
define Device/dlink_dap-2610
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2610
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
|
BLOCKSIZE := 64k
|
|
WRGG_DEVNAME := /dev/mtdblock/8
|
|
WRGG_SIGNATURE := wapac30_dkbs_dap2610
|
|
IMAGE_SIZE := 14080k
|
|
IMAGES += factory.bin
|
|
# Bootloader expects a special 160 byte header which is added by
|
|
# wrgg-image.
|
|
# Factory image size must be larger than 6MB, and size in wrgg header must
|
|
# match actual factory image size to be flashable from D-Link http server.
|
|
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
|
|
# cannot be part of the wrgg image. This is solved in the factory image by
|
|
# having the rootfs at the end of the image (without pad-rootfs). And in
|
|
# the sysupgrade image only the kernel is included in the wrgg checksum,
|
|
# but this is not flashable from the D-link http server.
|
|
# append-rootfs must start on an erase block boundary.
|
|
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2610
|
|
|
|
define Device/edgecore_ecw5211
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Edgecore
|
|
DEVICE_MODEL := ECW5211
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
|
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm
|
|
endef
|
|
TARGET_DEVICES += edgecore_ecw5211
|
|
|
|
define Device/edgecore_oap100
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Edgecore
|
|
DEVICE_MODEL := OAP100
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
|
|
DEVICE_PACKAGES := ipq-wifi-edgecore_oap100 kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += edgecore_oap100
|
|
|
|
define Device/engenius_eap1300
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP1300
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BOARD_NAME := eap1300
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 25344k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += engenius_eap1300
|
|
|
|
define Device/engenius_eap2200
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP2200
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += engenius_eap2200
|
|
|
|
define Device/engenius_emd1
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EMD1
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
IMAGE_SIZE := 30720k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += engenius_emd1
|
|
|
|
define Device/engenius_emr3500
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EMR3500
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 30720k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
|
DEFAULT := n
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += engenius_emr3500
|
|
|
|
define Device/engenius_ens620ext
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ENS620EXT
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BLOCKSIZE := 64k
|
|
PAGESIZE := 256
|
|
BOARD_NAME := ENS620EXT
|
|
VENDOR_ID := 0x0101
|
|
PRODUCT_ID := 0x79
|
|
PRODUCT_ID_NEW := 0xA4
|
|
DATECODE := 190507
|
|
FW_VER := 3.1.2
|
|
FW_VER_NEW := 3.5.6
|
|
CW_VER := 1.8.99
|
|
IMAGE_SIZE := 21312k
|
|
KERNEL_SIZE := 5120k
|
|
FILESYSTEMS := squashfs
|
|
IMAGES += factory_30.bin factory_35.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
|
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += engenius_ens620ext
|
|
|
|
define Device/extreme-networks_ws-ap3915i
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Extreme Networks
|
|
DEVICE_MODEL := WS-AP3915i
|
|
IMAGE_SIZE := 30080k
|
|
SOC := qcom-ipq4029
|
|
BLOCKSIZE := 128k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-extreme-networks_ws-ap3915i
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += extreme-networks_ws-ap3915i
|
|
|
|
define Device/ezviz_cs-w3-wd1200g-eup
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EZVIZ
|
|
DEVICE_MODEL := CS-W3-WD1200G
|
|
DEVICE_VARIANT := EUP
|
|
IMAGE_SIZE := 14848k
|
|
KERNEL_SIZE = 6m
|
|
SOC := qcom-ipq4018
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
append-metadata
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := uboot's bootcmd has to be updated (see wiki). \
|
|
Upgrade via sysupgrade mechanism is not possible.
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
|
|
|
define Device/glinet_gl-a1300
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-A1300
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 131072k
|
|
DEVICE_PACKAGE := ipq-wifi-glinet_gl-a1300
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-a1300
|
|
|
|
define Device/glinet_gl-ap1300
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AP1300
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 131072k
|
|
KERNEL_INSTALL := 1
|
|
DEVICE_PACKAGES := ipq-wifi-glinet_gl-ap1300 kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += glinet_gl-ap1300
|
|
|
|
define Device/glinet_gl-b1300
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-B1300
|
|
BOARD_NAME := gl-b1300
|
|
SOC := qcom-ipq4029
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-b1300
|
|
|
|
define Device/glinet_gl-b2200
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-B2200
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c3
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
|
IMAGES := emmc.img.gz sysupgrade.bin
|
|
IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
|
|
pad-to 1024k | append-kernel |\
|
|
pad-to 33792k | append-rootfs |\
|
|
append-metadata | gzip
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct \
|
|
kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-b2200
|
|
|
|
define Device/glinet_gl-s1300
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-S1300
|
|
SOC := qcom-ipq4029
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += glinet_gl-s1300
|
|
|
|
define Device/kernel-size-6350-8300
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Kernel partition size must be increased for \
|
|
this OpenWrt version. Before continuing, you MUST issue either the \
|
|
command "fw_setenv kernsize 500000" from the OpenWrt command line, \
|
|
or "setenv kernsize 500000 ; saveenv" from the U-Boot serial console. \
|
|
Instead of the sysupgrade image, you must then install the OpenWrt \
|
|
factory image, setting the force flag and wiping the configuration. \
|
|
(e.g. "sysupgrade -n -F openwrt-squashfs-factory.bin" on command line)
|
|
endef
|
|
|
|
define Device/linksys_ea6350v3
|
|
# The Linksys EA6350v3 has a uboot bootloader that does not
|
|
# support either booting lzma kernel images nor booting UBI
|
|
# partitions. This uboot, however, supports raw kernel images and
|
|
# gzipped images.
|
|
#
|
|
# As configured by the OEM factory, the device will boot the kernel
|
|
# from a fixed address with a fixed length of 3 MiB. Also, the
|
|
# device has a hard-coded kernel command line that requires the
|
|
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
|
# Oh... and the kernel partition overlaps with the rootfs
|
|
# partition (the same for alt_kernel and alt_rootfs).
|
|
#
|
|
# If you are planing re-partitioning the device, you may want to
|
|
# keep these details in mind:
|
|
# 1. The kernel addresses you should honor are 0x00000000 and
|
|
# 0x02800000 respectively.
|
|
# 2. The kernel size (plus the dtb) cannot exceed 3 MiB in size
|
|
# unless the uboot environment variable "kernsize" is increased.
|
|
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
|
# 4. The kernel command line from uboot is harcoded to boot with
|
|
# rootfs either in mtd11 or mtd13.
|
|
$(call Device/FitzImage)
|
|
$(call Device/kernel-size-6350-8300)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA6350
|
|
DEVICE_VARIANT := v3
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 35840k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
|
|
endef
|
|
TARGET_DEVICES += linksys_ea6350v3
|
|
|
|
define Device/linksys_ea8300
|
|
$(call Device/FitzImage)
|
|
$(call Device/kernel-size-6350-8300)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA8300
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 84992k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8300
|
|
|
|
define Device/linksys_mr8300
|
|
$(call Device/FitzImage)
|
|
$(call Device/kernel-size-6350-8300)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := MR8300
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 84992k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += linksys_mr8300
|
|
|
|
define Device/linksys_whw01
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := WHW01
|
|
KERNEL_SIZE := 6144k
|
|
IMAGE_SIZE := 75776K
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW01
|
|
DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x
|
|
endef
|
|
TARGET_DEVICES += linksys_whw01
|
|
|
|
define Device/luma_wrtq-329acn
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Luma Home
|
|
DEVICE_MODEL := WRTQ-329ACN
|
|
SOC := qcom-ipq4018
|
|
DEVICE_PACKAGES := kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio
|
|
IMAGE_SIZE := 76632k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
endef
|
|
TARGET_DEVICES += luma_wrtq-329acn
|
|
|
|
define Device/meraki_mr33
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
DEVICE_MODEL := MR33
|
|
SOC := qcom-ipq4029
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
endef
|
|
TARGET_DEVICES += meraki_mr33
|
|
|
|
define Device/meraki_mr74
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
DEVICE_MODEL := MR74
|
|
SOC := qcom-ipq4029
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
DEVICE_DTS_CONFIG := config@3
|
|
endef
|
|
TARGET_DEVICES += meraki_mr74
|
|
|
|
define Device/mobipromo_cm520-79f
|
|
$(call Device/FitzImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := MobiPromo
|
|
DEVICE_MODEL := CM520-79F
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += mobipromo_cm520-79f
|
|
|
|
define Device/netgear_ex61x0v2
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_DTS_CONFIG := config@4
|
|
NETGEAR_BOARD_ID := EX6150v2series
|
|
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
|
IMAGE_SIZE := 14400k
|
|
SOC := qcom-ipq4018
|
|
endef
|
|
|
|
define Device/netgear_ex6100v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_MODEL := EX6100
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += netgear_ex6100v2
|
|
|
|
define Device/netgear_ex6150v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_MODEL := EX6150
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += netgear_ex6150v2
|
|
|
|
define Device/netgear_orbi
|
|
$(call Device/DniImage)
|
|
SOC := qcom-ipq4019
|
|
DEVICE_VENDOR := NETGEAR
|
|
IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \
|
|
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-rootfs | pad-rootfs | netgear-dni
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \
|
|
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
|
|
endef
|
|
|
|
define Device/netgear_rbx50
|
|
$(call Device/netgear_orbi)
|
|
NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4
|
|
KERNEL_SIZE := 3932160
|
|
ROOTFS_SIZE := 32243712
|
|
IMAGE_SIZE := 36175872
|
|
endef
|
|
|
|
define Device/netgear_rbr50
|
|
$(call Device/netgear_rbx50)
|
|
DEVICE_MODEL := RBR50
|
|
DEVICE_VARIANT := v1
|
|
NETGEAR_BOARD_ID := RBR50
|
|
endef
|
|
TARGET_DEVICES += netgear_rbr50
|
|
|
|
define Device/netgear_rbs50
|
|
$(call Device/netgear_rbx50)
|
|
DEVICE_MODEL := RBS50
|
|
DEVICE_VARIANT := v1
|
|
NETGEAR_BOARD_ID := RBS50
|
|
endef
|
|
TARGET_DEVICES += netgear_rbs50
|
|
|
|
define Device/netgear_srx60
|
|
$(call Device/netgear_orbi)
|
|
NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4
|
|
KERNEL_SIZE := 3932160
|
|
ROOTFS_SIZE := 32243712
|
|
IMAGE_SIZE := 36175872
|
|
endef
|
|
|
|
define Device/netgear_srr60
|
|
$(call Device/netgear_srx60)
|
|
DEVICE_MODEL := SRR60
|
|
NETGEAR_BOARD_ID := SRR60
|
|
endef
|
|
TARGET_DEVICES += netgear_srr60
|
|
|
|
define Device/netgear_srs60
|
|
$(call Device/netgear_srx60)
|
|
DEVICE_MODEL := SRS60
|
|
NETGEAR_BOARD_ID := SRS60
|
|
endef
|
|
TARGET_DEVICES += netgear_srs60
|
|
|
|
define Device/netgear_wac510
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Netgear
|
|
DEVICE_MODEL := WAC510
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGES += factory.tar
|
|
IMAGE/factory.tar := append-ubi | wac5xx-netgear-tar
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += netgear_wac510
|
|
|
|
define Device/openmesh_a42
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_MODEL := A42
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@om.a42
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15616k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
TARGET_DEVICES += openmesh_a42
|
|
|
|
define Device/openmesh_a62
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_MODEL := A62
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@om.a62
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += openmesh_a62
|
|
|
|
define Device/p2w_r619ac
|
|
$(call Device/FitzImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := P&W
|
|
DEVICE_MODEL := R619AC
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@10
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
|
endef
|
|
|
|
define Device/p2w_r619ac-64m
|
|
$(call Device/p2w_r619ac)
|
|
DEVICE_VARIANT := 64M NAND
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
|
endef
|
|
TARGET_DEVICES += p2w_r619ac-64m
|
|
|
|
define Device/p2w_r619ac-128m
|
|
$(call Device/p2w_r619ac)
|
|
DEVICE_VARIANT := 128M NAND
|
|
endef
|
|
TARGET_DEVICES += p2w_r619ac-128m
|
|
|
|
define Device/pakedge_wr-1
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Pakedge
|
|
DEVICE_MODEL := WR-1
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
|
DEVICE_PACKAGES := ipq-wifi-pakedge_wr-1
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += pakedge_wr-1
|
|
|
|
define Device/plasmacloud_pa1200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
DEVICE_MODEL := PA1200
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@pc.pa1200
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15616k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa1200
|
|
|
|
define Device/plasmacloud_pa2200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
DEVICE_MODEL := PA2200
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@pc.pa2200
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa2200
|
|
|
|
define Device/qcom_ap-dk01.1-c1
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP-DK01.1
|
|
DEVICE_VARIANT := C1
|
|
BOARD_NAME := ap-dk01.1-c1
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
$(call Device/FitImage)
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
|
|
DEFAULT := n
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
|
|
|
define Device/qcom_ap-dk04.1-c1
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP-DK04.1
|
|
DEVICE_VARIANT := C1
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4048k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap-dk04.1-c1
|
|
DEFAULT := n
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
|
|
|
define Device/qxwlan_e2600ac-c1
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E2600AC
|
|
DEVICE_VARIANT := C1
|
|
BOARD_NAME := e2600ac-c1
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac-c1
|
|
DEFAULT := n
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += qxwlan_e2600ac-c1
|
|
|
|
define Device/qxwlan_e2600ac-c2
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E2600AC
|
|
DEVICE_VARIANT := C2
|
|
SOC := qcom-ipq4019
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac-c2
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += qxwlan_e2600ac-c2
|
|
|
|
define Device/sony_ncp-hg100-cellular
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Sony
|
|
DEVICE_MODEL := NCP-HG100/Cellular
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c4
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 8192k
|
|
IMAGE_SIZE := 128m
|
|
DEVICE_PACKAGES := e2fsprogs ipq-wifi-sony_ncp-hg100-cellular \
|
|
kmod-fs-ext4 uqmi
|
|
endef
|
|
TARGET_DEVICES += sony_ncp-hg100-cellular
|
|
|
|
define Device/teltonika_rutx10
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Teltonika
|
|
DEVICE_MODEL := RUTX10
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@5
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-teltonika_rutx kmod-bluetooth
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += teltonika_rutx10
|
|
|
|
define Device/tel_x1pro
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Telco
|
|
DEVICE_MODEL := X1 Pro
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
DEFAULT := n
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += tel_x1pro
|
|
|
|
define Device/unielec_u4019-32m
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Unielec
|
|
DEVICE_MODEL := U4019
|
|
DEVICE_VARIANT := 32M
|
|
BOARD_NAME := u4019-32m
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEFAULT := n
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += unielec_u4019-32m
|
|
|
|
define Device/zte_mf18a
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := ZTE
|
|
DEVICE_MODEL := MF18A
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_IN_UBI := 1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct ipq-wifi-zte_mf18a
|
|
endef
|
|
TARGET_DEVICES += zte_mf18a
|
|
|
|
define Device/zte_mf28x_common
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := ZTE
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_IN_UBI := 1
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
endef
|
|
|
|
define Device/zte_mf286d
|
|
$(call Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286D
|
|
endef
|
|
TARGET_DEVICES += zte_mf286d
|
|
|
|
define Device/zte_mf289f
|
|
$(call Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF289F
|
|
DEVICE_PACKAGES += ipq-wifi-zte_mf289f ath10k-firmware-qca9984-ct
|
|
endef
|
|
TARGET_DEVICES += zte_mf289f
|
|
|
|
define Device/zyxel_nbg6617
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6617
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 4096k
|
|
ROOTFS_SIZE := 24960k
|
|
RAS_BOARD := NBG6617
|
|
RAS_ROOTFS_SIZE := 19840k
|
|
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGES += factory.bin
|
|
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
|
# at least as large as the one of the initial firmware image (not the current
|
|
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
|
# this minimum-size. However, the larger image can be flashed both ways.
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6617
|
|
|
|
define Device/zyxel_wre6606
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := WRE6606
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
IMAGE_SIZE := 13184k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
endef
|
|
# Missing DSA Setup
|
|
#TARGET_DEVICES += zyxel_wre6606
|