RepoMirrors
/
openwrt
mirror of git://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
openwrt/target/linux/realtek/dts/rtl9302_zyxel_xgs1250-12.dts

424 lines
8.5 KiB
Plaintext
Raw Permalink Blame History

// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
#include "rtl930x.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "zyxel,xgs1250-12", "realtek,rtl838x-soc";
model = "Zyxel XGS1250-12 Switch";
aliases {
led-boot = &led_pwr_sys;
led-failsafe = &led_pwr_sys;
led-running = &led_pwr_sys;
led-upgrade = &led_pwr_sys;
};
keys {
compatible = "gpio-keys";
mode {
label = "reset";
gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
/* i2c of the SFP cage: port 12 */
i2c0: i2c-rtl9300@1b00036c {
compatible = "realtek,rtl9300-i2c";
reg = <0x1b00036c 0x3c>;
#address-cells = <1>;
#size-cells = <0>;
sda-pin = <10>;
scl-pin = <8>;
clock-frequency = <100000>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinmux_disable_sys_led>;
led_pwr_sys: led-0 {
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_POWER;
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
};
};
sfp0: sfp-p12 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpio0 17 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio0 16 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
};
led_set: led_set {
compatible = "realtek,rtl9300-leds";
active-low;
led_set0 = <0x0a20 0x0b80>; // LED set 0: 1000Mbps, 10/100Mbps
led_set1 = <0x0a0b 0x0a28 0x0a82 0x0a0b>; // LED set 1: (10G, 5G, 2.5G) (2.5G, 1G)
// (5G, 10/100) (10G, 5G, 2.5G)
led_set2 = <0x0a20 0x0a01>; // LED set 2: 1000MBit, 10GBit
};
thermal-zones {
phy24-thermal {
/* Poll every 10 seconds */
polling-delay-passive = <10000>;
polling-delay = <10000>;
thermal-sensors = <&phy24>;
trips {
phy24_trip0: phy24-trip0 {
/* At 80 degrees turn on fan */
temperature = <80000>;
hysteresis = <1000>;
type = "active";
};
phy24_trip1: phy24-trip1 {
/* At 108 degrees phys exceed spec */
temperature = <108000>;
hysteresis = <5000>;
type = "critical";
};
};
cooling-maps {
map {
trip = <&phy24_trip0>;
cooling-device = <&chassis_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
phy25-thermal {
/* Poll every 10 seconds */
polling-delay-passive = <10000>;
polling-delay = <10000>;
thermal-sensors = <&phy25>;
trips {
phy25_trip0: phy25-trip0 {
/* At 80 degrees turn on fan */
temperature = <80000>;
hysteresis = <1000>;
type = "active";
};
phy25_trip1: phy25-trip1 {
/* At 108 degrees phys exceed spec */
temperature = <108000>;
hysteresis = <5000>;
type = "critical";
};
};
cooling-maps {
map {
trip = <&phy25_trip0>;
cooling-device = <&chassis_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
phy26-thermal {
/* Poll every 10 seconds */
polling-delay-passive = <10000>;
polling-delay = <10000>;
thermal-sensors = <&phy26>;
trips {
phy26_trip0: phy26-trip0 {
/* At 80 degrees turn on fan */
temperature = <80000>;
hysteresis = <1000>;
type = "active";
};
phy26_trip1: phy26-trip1 {
/* At 108 degrees phys exceed spec */
temperature = <108000>;
hysteresis = <5000>;
type = "critical";
};
};
cooling-maps {
map {
trip = <&phy26_trip0>;
cooling-device = <&chassis_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
};
/* YEN SUN TECHNOLOGY FD122510LL-N fan */
chassis_fan: gpio-fan {
compatible = "gpio-fan";
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0
7000 1>;
#cooling-cells = <2>;
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0xe0000>;
read-only;
};
partition@e0000 {
label = "u-boot-env";
reg = <0xe0000 0x10000>;
};
partition@f0000 {
label = "u-boot-env2";
reg = <0xf0000 0x10000>;
read-only;
};
partition@100000 {
label = "jffs";
reg = <0x100000 0x100000>;
};
partition@200000 {
label = "jffs2";
reg = <0x200000 0x100000>;
};
partition@b300000 {
label = "firmware";
reg = <0x300000 0xce0000>;
compatible = "openwrt,uimage", "denx,uimage";
openwrt,ih-magic = <0x93001250>;
};
partition@fe0000 {
label = "log";
reg = <0xfe0000 0x20000>;
};
};
};
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
/* External RTL8218D PHY */
phy0: ethernet-phy@0 {
reg = <0>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 0>;
sds = < 2 >;
// Disabled because we do not know how to bring up again
// reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
};
phy1: ethernet-phy@1 {
reg = <1>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 1>;
};
phy2: ethernet-phy@2 {
reg = <2>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 2>;
};
phy3: ethernet-phy@3 {
reg = <3>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 3>;
};
phy4: ethernet-phy@4 {
reg = <4>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 4>;
};
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 5>;
};
phy6: ethernet-phy@6 {
reg = <6>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 6>;
};
phy7: ethernet-phy@7 {
reg = <7>;
compatible = "ethernet-phy-ieee802.3-c22";
rtl9300,smi-address = <0 7>;
};
/* External Aquantia 113C PHYs */
phy24: ethernet-phy@24 {
reg = <24>;
compatible = "ethernet-phy-ieee802.3-c45";
rtl9300,smi-address = <1 8>;
sds = < 6 >;
// Disabled because we do not know how to bring up again
// reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
#thermal-sensor-cells = <0>;
};
phy25: ethernet-phy@25 {
reg = <25>;
compatible = "ethernet-phy-ieee802.3-c45";
rtl9300,smi-address = <2 8>;
sds = < 7 >;
// Disabled because we do not know how to bring up again
// reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
#thermal-sensor-cells = <0>;
};
phy26: ethernet-phy@26 {
reg = <26>;
compatible = "ethernet-phy-ieee802.3-c45";
rtl9300,smi-address = <3 8>;
sds = < 8 >;
// Disabled because we do not know how to bring up again
// reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
#thermal-sensor-cells = <0>;
};
/* SFP Ports */
phy27: ethernet-phy@27 {
compatible = "ethernet-phy-ieee802.3-c22";
phy-is-integrated;
reg = <27>;
sds = < 9 >;
};
};
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
phy-handle = <&phy0>;
phy-mode = "xgmii";
led-set = <0>;
};
port@1 {
reg = <1>;
label = "lan2";
phy-handle = <&phy1>;
phy-mode = "xgmii";
led-set = <0>;
};
port@2 {
reg = <2>;
label = "lan3";
phy-handle = <&phy2>;
phy-mode = "xgmii";
led-set = <0>;
};
port@3 {
reg = <3>;
label = "lan4";
phy-handle = <&phy3>;
phy-mode = "xgmii";
led-set = <0>;
};
port@4 {
reg = <4>;
label = "lan5";
phy-handle = <&phy4>;
phy-mode = "xgmii";
led-set = <0>;
};
port@5 {
reg = <5>;
label = "lan6";
phy-handle = <&phy5>;
phy-mode = "xgmii";
led-set = <0>;
};
port@6 {
reg = <6>;
label = "lan7";
phy-handle = <&phy6>;
phy-mode = "xgmii";
led-set = <0>;
};
port@7 {
reg = <7>;
label = "lan8";
phy-handle = <&phy7>;
phy-mode = "xgmii";
led-set = <0>;
};
port@24 {
reg = <24>;
label = "lan9";
phy-mode = "usxgmii";
phy-handle = <&phy24>;
led-set = <1>;
};
port@25 {
reg = <25>;
label = "lan10";
phy-mode = "usxgmii";
phy-handle = <&phy25>;
led-set = <1>;
};
port@26 {
reg = <26>;
label = "lan11";
phy-mode = "usxgmii";
phy-handle = <&phy26>;
led-set = <1>;
};
port@27 {
reg = <27>;
label = "lan12";
phy-mode = "1000base-x";
phy-handle = <&phy27>;
sfp = <&sfp0>;
led-set = <2>;
managed = "in-band-status";
};
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <10000>;
full-duplex;
};
};
};
};
Reference in New Issue View Git Blame Copy Permalink