openwrt/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000-xe3...

274 lines
4.6 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7981.dtsi"
/ {
chosen {
bootargs = "console=ttyS0,115200n8 root=PARTLABEL=rootfs rootwait";
};
aliases {
label-mac-device = &gmac0;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "fixed-5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
regulator-always-on;
};
fan_5v: regulator-fan-5v {
compatible = "regulator-fixed";
regulator-name = "fan";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpios = <&pio 28 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
gpio-keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
};
};
gpio-export {
compatible = "gpio-export";
hub_power {
gpio-export,name = "hub_power";
gpio-export,output = <1>;
gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
};
5G_power {
gpio-export,name = "5G_power";
gpio-export,output = <1>;
gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
};
5G_control {
gpio-export,name = "5G_control";
gpio-export,output = <1>;
gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
};
5G_reset {
gpio-export,name = "5G_reset";
gpio-export,output = <0>;
gpios = <&pio 10 GPIO_ACTIVE_HIGH>;
};
};
leds {
compatible = "gpio-leds";
wifi2g {
label = "green:wifi2g";
gpios = <&pio 30 GPIO_ACTIVE_LOW>;
};
wifi5g {
label = "green:wifi5g";
gpios = <&pio 38 GPIO_ACTIVE_LOW>;
};
5g_led1 {
label = "green:5g:led1";
gpios = <&pio 6 GPIO_ACTIVE_LOW>;
};
5g_led2 {
label = "green:5g:led2";
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
};
5g_led3 {
label = "green:5g:led3";
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
};
5g_led4 {
label = "green:5g:led4";
gpios = <&pio 4 GPIO_ACTIVE_HIGH>;
};
led_power: power {
label = "green:power";
gpios = <&pio 39 GPIO_ACTIVE_LOW>;
};
wan {
label = "green:wan";
gpios = <&pio 31 GPIO_ACTIVE_LOW>;
};
};
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&mmc0 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&mmc0_pins_default>;
pinctrl-1 = <&mmc0_pins_uhs>;
bus-width = <8>;
max-frequency = <52000000>;
cap-mmc-highspeed;
vmmc-supply = <&reg_3p3v>;
non-removable;
status = "okay";
card@0 {
compatible = "mmc-card";
reg = <0>;
block {
compatible = "block-device";
partitions {
block-partition-env {
partname = "u-boot-env";
nvmem-layout {
compatible = "u-boot,env";
};
};
block-partition-factory {
partname = "factory";
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x1000>;
};
macaddr_factory_a: macaddr@a {
compatible = "mac-base";
reg = <0xa 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
};
};
};
};
&mdio_bus {
reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
reset-delay-us = <600>;
reset-post-delay-us = <20000>;
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "ethernet-phy-ieee802.3-c45";
};
};
&eth {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
phy-handle = <&phy5>;
nvmem-cells = <&macaddr_factory_a 0>;
nvmem-cell-names = "mac-address";
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "gmii";
phy-handle = <&int_gbe_phy>;
nvmem-cells = <&macaddr_factory_a 1>;
nvmem-cell-names = "mac-address";
};
};
&pio {
mmc0_pins_default: mmc0-pins-default {
mux {
function = "flash";
groups = "emmc_8";
};
};
mmc0_pins_uhs: mmc0-pins-uhs {
mux {
function = "flash";
groups = "emmc_8";
};
};
pcie_pins: pcie-pins {
mux {
function = "pcie";
groups = "pcie_pereset", "pcie_clk", "pcie_wake";
};
};
pwm0_pin: pwm0-pin-g0 {
mux {
function = "pwm";
groups = "pwm0_1";
};
};
};
&xhci {
phys = <&u2port0 PHY_TYPE_USB2>;
vbus-supply = <&reg_5v>;
mediatek,u3p-dis-msk = <0x01>;
status = "okay";
};
&usb_phy {
status = "okay";
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pcie_pins>;
status = "okay";
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
};
&wifi {
nvmem-cells = <&eeprom_factory_0>;
nvmem-cell-names = "eeprom";
status = "okay";
};
&fan {
pwms = <&pwm 0 40000 0>;
fan-supply = <&fan_5v>;
interrupt-parent = <&pio>;
interrupts = <29 IRQ_TYPE_EDGE_RISING>;
status = "okay";
};