176 lines
2.8 KiB
Plaintext
176 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include "mt7622-buffalo-wsr.dtsi"
|
|
|
|
/ {
|
|
model = "Buffalo WSR-3200AX4S";
|
|
compatible = "buffalo,wsr-3200ax4s", "mediatek,mt7622";
|
|
|
|
memory {
|
|
reg = <0 0x40000000 0 0x1f000000>;
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
/* Serial NAND is shared pin with SPI-NOR */
|
|
serial_nand_pins: serial-nand-pins {
|
|
mux {
|
|
function = "flash";
|
|
groups = "snfi";
|
|
};
|
|
|
|
conf-cmd-dat {
|
|
pins = "SPI_WP", "SPI_HOLD", "SPI_MOSI",
|
|
"SPI_MISO", "SPI_CS";
|
|
input-enable;
|
|
drive-strength = <16>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
conf-clk {
|
|
pins = "SPI_CLK";
|
|
drive-strength = <16>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio {
|
|
switch@1f {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <31>;
|
|
reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@4 {
|
|
reg = <4>;
|
|
label = "wan";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&gmac0>;
|
|
phy-connection-type = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&snfi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&serial_nand_pins>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "spi-nand";
|
|
reg = <0>;
|
|
spi-max-frequency = <104000000>;
|
|
nand-ecc-engine = <&snfi>;
|
|
mediatek,bmt-v2;
|
|
mediatek,bmt-table-size = <0x1000>;
|
|
/*
|
|
* - Preloader - (kernel (6MiB, in firmware))
|
|
* - Kernel2 - WTB
|
|
*/
|
|
mediatek,bmt-remap-range = <0x0 0x8c0000>,
|
|
<0x1ac0000 0x5200000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Preloader";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "ATF";
|
|
reg = <0x80000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
label = "u-boot";
|
|
reg = <0xc0000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "u-boot-env";
|
|
reg = <0x140000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@1c0000 {
|
|
label = "factory";
|
|
reg = <0x1c0000 0x100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@2c0000 {
|
|
compatible = "brcm,trx";
|
|
brcm,trx-magic = <0x33504844>;
|
|
label = "firmware";
|
|
reg = <0x2c0000 0x1800000>;
|
|
};
|
|
|
|
partition@1ac0000 {
|
|
label = "Kernel2";
|
|
reg = <0x1ac0000 0x1800000>;
|
|
};
|
|
|
|
partition@32c0000 {
|
|
label = "glbcfg";
|
|
reg = <0x32c0000 0x200000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@34c0000 {
|
|
label = "board_data";
|
|
reg = <0x34c0000 0x200000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@36c0000 {
|
|
label = "WTB";
|
|
reg = <0x36c0000 0x3600000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|