This restores the original config_generate behaviour. With MAC set for
bridged devices the bridge automatically gets its MAC adjusted (it picks
the lowest MAC of bridged devices).
This fixes confusing interfaces setup (bridge ports not having custom
MAC assigned).
Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Fixes: e002179a6d ("base-files: simplify setting device MAC")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Move code above interface generation
It results in more logical order. Device gets its config section
above interface section.
2. Drop the loop
We have separated code handling bridges now so $device should be
guaranteed to contain a single device name.
3. Drop section name
It's not required by netifd or LuCI & it's not needed by this script
as $device contains a single device name now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After the commit 43fc720657
("base-files: generate "device UCI type section for bridge"), the wrong
network configuration is generated for the devices that already have the
bridge device section for VLAN, such as the devices in realtek target.
As a result, the bridge device by additional "device" section is
specified to the "ports" option in the "bridge-vlan" section and netifd
shuts down the switch and the ethernet when the network service started.
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rmilecki: use $ports for generate_bridge_vlan argument]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Missing br- prefix could result in name conflict between DSA port
interface and bridge interface. Some devices with just one LAN port use
"lan" interface name for DSA port. Trying to create bridge with the same
"lan" name was failing.
Reported-by: David Bauer <mail@david-bauer.net>
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This switches from the old way of defining bridges in an "interface" UCI
section type (that should be used for layer 3 only). From now a defualt
board switch will have its own "device" UCI section type. It's a new &
preferred way of defining L2 devices.
Before:
config interface 'lan'
option type 'bridge'
option ifname 'lan1 lan2 lan3 lan4'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
After:
config device
option name 'lan'
option type 'bridge'
list ports 'lan1'
list ports 'lan2'
list ports 'lan3'
list ports 'lan4'
config interface 'lan'
option ifname 'lan'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Bridge aggregates multiple ports so use a more accurate name ("ports")
and format (array) for storing them in board.json.
Example:
"network": {
"lan": {
"ports": [
"lan1",
"lan2",
"lan3",
"lan4"
],
"protocol": "static"
},
"wan": {
"ifname": "wan",
"protocol": "dhcp"
}
}
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add code for setting mac addresses inside board.json and rendering
them out to uci. On switches we want to have a unique MAC on each port.
With 48 port switches that would require 48 device sections in
/etc/config/network. Doing so via board.json is easier.
Signed-off-by: John Crispin <john@phrozen.org>
Latest netifd allows us to setup network bridges with implicit vlan
tagging. For this to work, we need to setup several additional uci
sections. This feature is particularly usefull for DSA tupe devices.
Add board.d and uci-defaults support for generating the sections.
Signed-off-by: John Crispin <john@phrozen.org>
We regularly encounter the situation that devices are subject to
changes that will make them incompatible to previous versions.
Removing SUPPORTED_DEVICES will not really be helpful in most of these
cases, as this only helps after a rename.
To solve this situation, this patchset introduces a compatibility
version for devices. To complement the DEVICE_COMPAT_VERSION set
for the image to be flashed, this implements a compat_version on
the device, so it will have something to compare with the image.
The only viable way to achieve this seems to be via board.d files,
i.e. this is technically adding a compat version for the device's
config.
Like for the network setup, this will set up a command
ucidef_set_compat_version to set the compat_version in board.d.
This will then add a string to /etc/board.json, which will be
translated into uci system config by bin/config_generate.
By this, the compat_version, being a version of the config, will
also be exposed to the user.
As with DEVICE_COMPAT_VERSION, missing uci entry will be assumed
as compat_version "1.0", so we only need to add this if a device
needs to be bumped, e.g.
ucidef_set_compat_version "1.1"
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces deprecated backticks by more versatile $(...) syntax.
This does not touch lib/upgrade/nand.sh, as there replacement is
not trivial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As touch creates files with permission 0644 use umask to create
config files with permission 0600 to be inline with INSTALL_CONF
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:
ucidef_set_interface_lan "eth0 eth1.1"
ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01"
will return
config device 'lan_eth0_dev'
option name 'eth0'
option macaddr 'yy:yy:yy:yy:yy:01'
config device 'lan_eth1_1_dev'
option name 'eth1.1'
option macaddr 'yy:yy:yy:yy:yy:01'
ref: https://github.com/openwrt/openwrt/pull/2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 6170c46b47.
There has been demand for further evaluation of the impact of a
changed hostname, so this is reverted for now. The default hostname
will be "OpenWrt" again after this commit.
The macaddr_geteui() function is not removed by this revert.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If a label MAC address is provided for device, system
will rename the hostname with OpenWrt_{eui mac address}.
This helps to distinguish between different devices.
Since it's no good idea to nest json_* functions, this code does
not use get_mac_label directly, but only get_mac_label_dt as
external resource.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
[merged with commit introducing macaddr_geteui, rebased on updated
label MAC address storage, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If set, label MAC address is available from one of two sources,
device tree or board.json. So far, the function get_mac_label
was meant for retrieving the address, while an option in uci
system config was specified only for case 2 (board.json).
The uci config option has several drawbacks:
- it is only used for a fraction of devices (those not in DT)
- label MAC address is a device property, while config implies
user interaction
- label_macaddr option will only be set if /etc/config/system
does not exist (i.e. only for new installations)
Thus, this patch changes the behavior of get_mac_label:
Instead of writing the value in board.json to uci system config
and reading from this location afterwards, get_mac_label now
extracts data from board.json directly. The uci config option
won't be used anymore.
In addition, two utility functions for extraction only from DT
or from board.json are introduced.
Since this is only changing the access to the label MAC address, it
won't interfere with the addresses stored in the code base so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many devices, MAC addresses cannot be retrieved via the
device tree alias.
To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.
This is based on the work of Rosy Song <rosysong@rosinson.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The swconfig switch led driver has the ability to switch
between a "link, rx and/or tx" mode. However, this feature
was not implemented in uci, the led init script and
config_generate.
This patch adds a seventh parameter to the
ucidef_set_led_switch() function. The accepted values for
this parameter are: link, rx and tx.
Any permutations of these three values are supported, as
long as they are properly encased with quotes.
If the parameter is not specified it will default to "all"
(link rx tx).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
Setting ipv6 to auto in case of a pppoe interface will trigger the
creation of a dynamic wan_6 interface meaning two IPv6 interfaces
(wan6 and wan_6) will be active on top of the pppoe interface.
This leads to unpredictable behavior in the network; therefore set
ipv6 to 1 which will prevent the dynamic creation of the wan_6
interface.
Further alias the wan6 interface on top of the wan interface for pppoe
as the wan6 interface can only be started when the link local address is
ready. In case of pppoe the link local address is negotiated during the
Internet Protocol Control Protocol when the PPP link is setup meaning
all the IP address info is only available when the wan interface is up.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The name will appear in shell prompt and LuCI page title. Uppercase
letters seem to be more vigorous
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"
This adds a proper object to the board.json, e.g.
"usb": {
"name": "USB",
"type": "usbport",
"sysfs": "devicename:colour:function",
"ports": [
"usb1-port1",
"usb2-port1"
]
}
and supports translating it into uci section.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Before a configuration is generated, an empty file is created to store
it in. (required by UCI)
If something happens during config generation
(power cut, interruption, ..) an empty file exists and it is never
regenerated again, causing some daemons to fail starting
(NTPD, logread, ..)
Fix this by also generating new configs if a critical file
is empty.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Instead of board_detect generating the config as a side effect, let
config_generate call board_detect as needed.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This commit:
1) seed /dev/urandom with the saved seeds as early as possible
(see /lib/preinit/81_urandom_seed)
2) save a seed at /etc/urandom.seed if it doesn't exists
3) save a new seed each boot at "system.@system[0].urandom_seed"
(see /etc/init.d/urandom_seed)
We use getrandom() so we are sure /dev/urandom pool is initialized
Seed size is 512 bytes (ie /proc/sys/kernel/random/poolsize / 8)
it's the same size as in ubuntu 14.04 and all systemd systems
Seeding /dev/urandom doesn't change entropy estimation, so we still have
"random: ubus urandom read with 4 bits of entropy available"
messages in the logs, but we can now ignore them if
after "urandom-seed: Seeding with ..." message
Saving a new seed on each boot is disabled by default to avoid too much
writes without user consent
v2: log preinit messages to /dev/kmsg
v3: use non generic function name for logging, as /lib/preinit/ files
are all sourced together in /etc/preinit
v4: after a lot of discussion on the ML, use a uci config param
v5: config param is now the path of the seed
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Increase the default system log buffer size
from 16 kB (built-in default in ubox logd)
to 64 kB by setting the option in /etc/config/system.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Now that config_generate is able to generate the entire /etc/config/system
from scratch we can apply the same logic as used for /etc/config/network;
when the configuration file exists already then do not do anything, else
generate it from the values provided by /etc/board.json .
In order to facilitate that move the file existance checking inside
/bin/config_generate and call it unconditionally from /bin/board_detect.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The json_select call fails when there are no roles or ports objects in board.json. "json_select .." must not be executed after failing.
This fixes for example LEDs not being set up in /etc/config/system.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Instead of having two different types adsl and vdsl just create one dsl
type. This way we can use the same luci code for adsl and vdsl and the
config parameters are not so different.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48944
This patch adds extra parameter to switch LED trigger initialization
functions. New functionality maintains backward compatibility, so
calling functions without setting new speed_mask parameter works
as expected.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48776
oneshot and timer have the same configuration options, just a different
trigger name.
Signed-off-by: Karl Palsson <karlp@etactica.com>
SVN-Revision: 48770
This adds support for specifying the dsl modem, atm bridge configs and setting
the pppoe protocol for wan.
These additions are required to port the Lantiq target to board.d.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47750
Rafał Miłecki
INAGAKI Hiroshi
Adrian Schmutzler
John Crispin
Hans Dedecker
Sungbo Eo
Rosy Song
Petr Štetiar
Christian Lamparter
Martin Schiller
Zoltan HERPAI
Yousong Zhou
Julian Labus
Koen Vandeputte
Jonas Gorski
Etienne CHAMPETIER
Jo-Philipp Wich
Hannu Nyman
Felix Fietkau
Vittorio Gambaletta (VittGam)
John Crispin
Hauke Mehrtens
Felix Fietkau
Jo-Philipp Wich
John Crispin