Commit Graph

18758 Commits

Author SHA1 Message Date
Sven Eckelmann
2796ab85ed ipq40xx: add support for Compex WPJ428
* QCA IPQ4028
* 256 MB of RAM
* 32 MB of SPI NOR flash (mx25l25635e)
* 128 MB of SPI NAND flash (gd5f1gq4ucy1g)
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2 fully software controllable GPIO-LEDs
* 2 additional GPIO-LEDs which also affect the SIM card detection
* 1x button (reset)
* 1x GPIO buzzer
* 1x USB (xHCI)
* 1x NGFF (USB-only with Dual-SIM support, untested)
* TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC)
* 2x gigabit ethernet
  - phy@mdio4:
    + Manual: Ethernet port 0
    + gmac0 (ethaddr) in original firmware
    + 802.3af POE (HV version)
    + 24v passive POE (LV version)
  - phy@mdio3:
    + Manual: Ethernet port 1
    + gmac1 (eth1addr) in original firmware
* DC Jack connector
  + 24-56V (HV version)
  + 12-24V (LV version)

The SPI NAND flash isn't supported at the moment.

The bootloader has to be updated before OpenWrt is installed to fix a
reboot problem. The nor-ipq40xx-single.img from
https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware
has to be downloaded and the transfered in u-boot via TFTP

  set ipaddr 192.168.1.11
  set serverip 192.168.1.10
  ping ${serverip}
  tftpboot 0x84000000 nor-ipq40xx-single.img
  imgaddr=0x84000000 && source $imgaddr:script

The sysupgrade image can be installed directly on flash using u-boot:

  sf probe
  tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin
  sf erase 0x00180000 +$filesize
  sf write 0x84000000 0x00180000 $filesize
  bootipq

The initramfs image can be started using

  tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb
  set fdt_high 0x83000000
  bootm 0x82000000

The used SIM card slot can be changed using

  # slot 1 (also enables orange LED)
  echo 1 > /sys/class/gpio/gpio3/value
  # slot 2
  echo 0 > /sys/class/gpio/gpio3/value

It can be checked whether a SIM card is inserted in the current slot and
the red LED is subsequently on via:

  echo 2 > /sys/class/gpio/export
  cat /sys/class/gpio/gpio2/value

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-03-17 08:09:04 +01:00
INAGAKI Hiroshi
dbdc26ba33 ramips: fix switch for Nexx devices
There are 2 ethernet ports on Nexx WT1520 and WT3020. These ethernet
ports are assigned as follows, and other ports cannot be used.

- WT1520:
  - port0 -> lan
  - port4 -> wan

- WT3020:
  - port0 -> wan
  - port4 -> lan

I dropped ports that cannot be used.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-03-17 08:09:04 +01:00
Arne Zachlod
d0988235dd
ar71xx: add support for Ubiquiti Litebeam M5
Specification:
- SoC: Atheros AR9342
- Flash: 8 MiB
- RAM: 64 MiB
- UART: 1x UART on PCB - 115200 8N1
- Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A)

Doesn't work:
* Flash via TFTP with Ubiquiti Uboot

Installation via vendor firmware:
- upload factory image via webinterface

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2018-03-15 19:11:39 +01:00
Christian Mehlis
0c7e78930b ipq806x: add support for Compex WPQ864
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
           256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer

The correct amount of RAM will be passed by the bootloader.

In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.

So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.

OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.

It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.

In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:

  (IPQ) # set bootargs " "
  (IPQ) # set fsbootargs " "
  (IPQ) # saveenv

The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):

  (IPQ) # set serverip 192.168.1.20
  (IPQ) # set ipaddr 192.168.1.1

  (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
  (IPQ) # crc32 0x42000000 $filesize

  (IPQ) # nand erase 0x1340000 0x4000000
  (IPQ) # nand write 0x42000000 0x1340000 $filesize

The initramfs image can be started using:

  (IPQ) # set fdt_high 0x48000000
  (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
  (IPQ) # bootm 0x44000000

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 08:17:10 +01:00
Mathias Kresin
2d67ef8638 mvebu: unset uboot build by default
Initialise the UBOOT variable by default. Otherwise it will be
unintended inherit to following images if set and causes an uboot build
where not required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 07:50:41 +01:00
Hauke Mehrtens
bf4aa52dbf kernel: make mtd patches apply again
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.

Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-15 00:42:41 +01:00
Chris Blake
4943afd781 ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33

hardware highlights:

SOC:	IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND:	128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH:	Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1:	QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2:	Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3:	Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS:	1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
	1 x Orange LED Fault Indicator (shared with LP5562)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON:	one Reset button
MISC:	Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
	AT24C64 8KiB EEPROM
	Kensington Lock

Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	1x4 0.1" header with half-height/low profile pins.
	The pinout is: VCC (little white arrow), RX, TX, GND.

Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>

Add images to do an installation via bootloader:
 0. open up the MR33 and connect the serial console.

 1. start the 2nd stage bootloader transfer from client pc:

  # ubootwrite.py --write=mr33-uboot.bin
  (The ubootwrite tool will interrupt the boot-process and hence
   it needs to listen for cues. If the connection is bad (due to
   the low-profile pins), the tool can fail multiple times and in
   weird ways. If you are not sure, just use a terminal program
   and see what the device is doing there.

 2. power on the MR33 (with ethernet + serial cables attached)
    Warning: Make sure you do this in a private LAN that has
    no connection to the internet.

 - let it upload the u-boot this can take 250-300 seconds -

 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
    (the u-boot is listening on 192.168.1.1)
    # tftp 192.168.1.1
    binary
    put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin

 4. wait for it to reboot

 5. connect to your MR33 via ssh on 192.168.1.1

For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)

Thanks to Jerome C. for sending an MR33 to Chris.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:52 +01:00
Christian Lamparter
87c42101cf ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR:	2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND:   128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one Reset and one WPS button
LEDS:	Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has an unpopulated
	1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
	PCB right next to the connector.

U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.

Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)

To install the image permanently, you have to do the following
steps in the listed order.

1. Open up the router.
   There are four phillips screws hiding behind the four plastic
   feets on the underside.

2. Connect the serial cable (See notes above)

3. Connect your router via one of the four LAN-ports (yellow)
   to a PC which can set the IP-Address and ssh and scp from.

   If possible set your PC's IPv4 Address to 192.168.1.70
   (As this is the IP-Address the Router's bootloader expects
   for the tftp server)

4. power up the router and enter the u-boot
   choose option 1 to upload the initramfs image. And follow
   through the ipv4 setup.

Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).

3. Connect to the OpenWrt running in RAM

   The default IPv4-Address of your router will be 192.168.1.1.

   1. Copy over the openwrt-sysupgrade.bin image to your router's
      temporary directory

   # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp

   2. ssh from your PC into your router as root.

   # ssh root@192.168.1.1

   The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.

   Once connected...: run the following commands on your temporary installation

   3. delete the "jffs2" ubi partition to make room for your new root partition

   # ubirmvol /dev/ubi0 --name=jffs2

   4. install OpenWrt on the NAND Flash.

   # sysupgrade -v /tmp/openwrt-sysupgrade.bin

   - This will will automatically reboot the router -

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:51 +01:00
Mathias Kresin
249a9b35e0 ipq40xx: fix GL.iNet GL-B1300 support
Rename the dts file to match the used SoC type and drop the unnecessary
KERNEL_INSTALL from the image build code.

Remove the fixed rootfs and kernel partitions and create an image with
rootfs appended after kernel.

Setup a switch portmap matching the hardware and a default network/switch
configuration to make make the second lan port working. Use eth0 as lan
to have it consistent accross the target.

Use the power LED to indicate the boot status.

Sort the SoC entries within the dts by address and use dtc labels
whenever possible.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-03-14 19:04:51 +01:00
David Bauer
9f437b2cf3 ipq40xx: remove block- and pagesize from FB4040
This removes the block- and pagesize from the FritzBox 4040
image description, fixing incorrectly working sysupgrade.

With this commit, the default values for block- and pagesize are
used.

Signed-off-by: David Bauer <mail@david-bauer.net>
[chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:51 +01:00
Christian Lamparter
d0e9621404 ipq40xx: OpenMesh A42 overhaul
Sort the soc entries in the dts by address and use dtc labels whenever
possible.

Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an
IPQ4019.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:51 +01:00
Christian Lamparter
a44d435c1d ipq40xx: fix apss cpu overclocking spam
There's an interaction issue between the clk changes:"
clk: qcom: ipq4019: Add the apss cpu pll divider clock node
clk: qcom: ipq4019: remove fixed clocks and add pll clocks
" and the cpufreq-dt.

cpufreq-dt is now spamming the kernel-log with the following:

[ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP
for freq 761142857 (-34)

This only happens on certain devices like the Compex WPJ428
and AVM FritzBox!4040. However, other devices like the Asus
RT-AC58U and Meraki MR33 work just fine.

The issue stem from the fact that all higher CPU-Clocks
are achieved by switching the clock-parent to the P_DDRPLLAPSS
(ddrpllapss). Which is set by Qualcomm's proprietary bootcode
as part of the DDR calibration.

For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked
at round 533 MHz (ddrpllsdcc = 190285714 Hz).

whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is
clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:51 +01:00
Mathias Kresin
1b906723eb ipq40xx/ipq806x: move qcom-dwc3 usb driver to generic
If the a kernel package exists within multiple targets an error/warning
is shown.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-14 19:04:51 +01:00
John Crispin
54b275c8ed ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
John Crispin
b7f115f22a ipq806x: drop ipq40xx support
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Rafał Miłecki
ac9bcefa3b kernel: use V10 of mtd patchset adding support for "compatible" string
In the commit bde5e7a632 ("kernel: backport mtd implementation for
"compatible" in "partitions" subnode") patches that got accepted into
l2-mtd.git were backported to the kernels 4.9 and 4.14. Unfortunately
there was a regression report, patches were dropped and never reached
4.16.

This commit replaces these pseudo-backports with the latest version
that includes regression fix and futher changes that were requested.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-03-14 15:13:39 +01:00
Mathias Kresin
d482356322 ramips: mt7620n: add mdio node and disable port4 by default
Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").

The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load  with

  mtk_soc_eth 10100000.ethernet: no mdio-bus child node found

Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.

Fixes: FS#1428

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-13 20:18:15 +01:00
John Crispin
d57ca53ff9 Revert "ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=n"
This reverts commit cff2dedebc.

This patch causes build issues

Signed-off-by: John Crispin <john@phrozen.org>
2018-03-13 13:10:21 +01:00
Rafał Miłecki
9004fc3c76 kernel: b53: drop support for old location of bcm47xx_nvram.h
In kernels 4.0 and older that header file was located in some subdir of
arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so
that code isn't needed anymore.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-03-13 12:01:36 +01:00
André Draszik
cff2dedebc ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=n
If CONFIG_GPIO_SYSFS=n, compilation fails with
  drivers/built-in.o: In function `gpio_export_with_name':
  include/asm-generic/gpio.h:128: undefined reference to `__gpiod_export'

This is because the stub in that case has the wrong name,
_gpiod_export() - note the missing underscore (_) at the
start.

Fix the stub, and add the correct prototype for the real
implementation.

Signed-off-by: André Draszik <git@andred.net>
2018-03-13 08:34:58 +01:00
Felix Fietkau
ed3860c3e3 swconfig: convert swdevs_lock from spinlock to mutex
Should fix some sleep-while-atomic issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-12 12:50:46 +01:00
Felix Fietkau
9306bdf31c kernel: merge a pending fix for HFSC warnings/slowdowns (fixes FS#1136)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-11 08:58:53 +01:00
Felix Fietkau
4e8f1e9f4c kernel: unroll MIPS r4k cache blast function
Optimize the compiler output for larger cache blast cases that are
common for DMA-based networking.

On ar71xx, I measured a routing throughput increase of ~8%

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-10 11:58:19 +01:00
Hauke Mehrtens
b7b14fd64e sunxi: Fix B53 swconfig driver for Lamobo R1
This reverts the changes needed for the upstream b53 DSA switch driver
to use the OpenWrt b43 swconfig switch driver instead.

Tested-by: TheWerthFam <thewerthfam@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-10 01:15:22 +01:00
Antony Antony
d6634edfc1 sunxi: NanoPi NEO Plus2 backport Gigabit Ethernet DT node
Kernel 4.16 commit 27d7f9297027

Signed-off-by: Antony Antony <antony@phenome.org>
2018-03-10 01:15:22 +01:00
Tomasz Maciej Nowak
584d7c53bd mvebu: new subtarget cortex A53
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.

The first device is Globalscale ESPRESSObin. Some hardware specs:

SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
     processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
         µSD card slot with footprint for an optional 4GB EMMC
         4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
            USB 2.0
            µUSB port connected to PL2303SA (USB to serial bridge
            controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
           I2C, GPIOs, PWM, UART, SPI, MMC, etc
           MiniPCIe slot
Misc: Reset button, JTAG interface

Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:

 1. Interrupt boot process to run U-Boot command line,

 2. Run following commands:
    (for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
     setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
     saveenv

    (for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
     setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
     setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
     saveenv

 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-10 01:15:22 +01:00
Hauke Mehrtens
be3da900cd mvebu: Add subtarget for Cortex A9 build
This is in preparation for adding a subtarget for the Cortex A53 later.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-10 01:15:21 +01:00
Ryan Mounce
9f3f61a0d9 mvebu: add support for Turris Omnia
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.

An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.

Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.

Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.

Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem

Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv

Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.

Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-10 01:15:21 +01:00
Ryan Mounce
657ce9231d mvebu: generate ramdisk image by default
ramdisk images must be used in the installation process for upcoming
Turris Omnia support.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-09 22:19:11 +01:00
Ryan Mounce
7b33f6c1bb mvebu: disable DSA DT nodes for boards using mvsw61xx
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-09 22:19:07 +01:00
Koen Vandeputte
cfc5867bce kernel: bump 4.9 to 4.9.86
- Refreshed all patches
- Removed 1 patch which got upstreamed

Compile tested on: ar71xx (Rocket M5, Mikrotik RB2011)
Runtime tested on: ar71xx (Rocket M5, Mikrotik RB2011)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-03-09 22:13:19 +01:00
Kabuli Chana
7c1dae6e26 kernel: bump to version 4.14.25
compile/test target mvebu/rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2018-03-09 22:12:48 +01:00
Felix Fietkau
fa22714181 ar71xx: fix double registration of usb host mode devices, add usb client support for qca955x
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.

Add qca955x device mode support, tested on 8devices Rambutan.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-09 18:25:57 +01:00
Florian Fainelli
30d42f85ae uml: Remove 4.4 patches
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-08 11:44:26 -08:00
Rafał Miłecki
6c194078db bcm53xx: include patch adding WZR-900DHP LEDs support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-03-07 17:01:07 +01:00
Martin Schiller
d84ac78d6a lantiq/xrx200: add usif support to dts files
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-03-06 19:49:06 +01:00
Giuseppe Lippolis
aa5014dd1a ramips: mt7620n: enable port 4 as EPHY by default
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.

Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-06 19:49:06 +01:00
Pawel Dembicki
39b5218434 ramips: mt7620: power up ephy port 4
In some boards port 4 of mt7620 switch is powered down in bootloader
configuration as lan/wan package leak mitigation.

Reset ephy port 4 to default settings to power up the port.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[clarify issue in commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-06 19:49:05 +01:00
Felix Fietkau
83ddc3bfc2 ar71xx: fix mii bus irq assignment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Felix Fietkau
f62d2b9549 ar71xx: remove pdata->fifo_cfg*
The values are the same for all chipsets that use it

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Stijn Segers
e72b2464b1 kernel: bump 4.4 to 4.4.119
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.

* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).

Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.

Compile-tested on: ar71xx & oxnas.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
2018-03-03 12:58:56 +01:00
Magnus Kroken
5af85dab22 kernel: bump 4.9 to 4.9.85
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-03-03 12:58:55 +01:00
Hauke Mehrtens
45fdb12258 kernel: generic: Add kernel configuration options
These options are needed for the mvebu arm64 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-02 23:15:28 +01:00
Stijn Segers
b5469b38cd kernel: bump 4.14 to 4.14.23
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
  the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.

Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-03-02 21:33:08 +01:00
Tomasz Maciej Nowak
844bdf94e4 mvebu: base-files: moving on from net-tools
Remove dependency on net-tools, replacing calls to ifconfig with iproute
equivalent, in functions changing interface MAC addresses.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:08 +01:00
Tomasz Maciej Nowak
d29a2814b7 mvebu: rename clearfog sysupgrade script and functions
Cosmetic name change of ClearFog sysupgrade script and its functions to
more generic sdcard. This way it won't be confusing for other future
device additions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:08 +01:00
Tomasz Maciej Nowak
b1317a10f7 mvebu: remove fs declaration in mount commands
Allows to have other file system for boot partition without breaking
sysupgrade.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:08 +01:00
Tomasz Maciej Nowak
0ef28ea387 mvebu: unify boot.scr creation
Unify boot.scr generation so Makefile for device image generation won't
grow without a reason. Also make boot-scr step optional.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:08 +01:00
Tomasz Maciej Nowak
e4fa22397f mvebu: make sdcard bootloader option configurable
Remove the necessity for boot loader from SD card image creation process
and make it configurable.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:07 +01:00
Tomasz Maciej Nowak
e10ea566cc mvebu: fix partition type and signature for sdcard
Previously the partition signature was assigned from provided type. Now
both are corrected wherein signature is always generated from
SOURCE_DATE_EPOCH. With that the root file system can be identified
by PARTUUID string, without relying on static declaration of device node.
This commit also does some cosmetics, removing trailing whitespace and
replacing spaces with tab.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-02 21:33:07 +01:00