mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-27 00:52:36 +00:00
ramips: add support for Netgear WAX214v2
Netgear WAX214v2 is an 802.11ax (Wi-Fi 6) wireless access point. Specifications: * SoC: MediaTek MT7621AT * RAM: 512 MiB * Flash: NAND 128 MiB (ESMT PSU1GA30DT) * Wi-Fi: 2.4/5 GHz 4T4R (MediaTek MT7915E) * Ethernet: 1x 10/100/1000 Mbps LAN * Switch: MediaTek MT7530 (SoC built-in) * LEDs/Keys * Power (green, blue, amber) * LAN (green, amber) * WLAN 2.4GHz (green, blue) * WLAN 5GHz (green, blue) * Reset button * USB: None * UART: Marked J1 on board, 115200 8N1 * Power * 12 VDC, 1.5 A * IEEE 802.3at (PoE+) Load addresses (same as Netgear WAX202): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry MAC addresses as verified by OEM firmware: vendor OpenWrt address eth0 lan label ra0 phy0 label + 2 rax0 phy1 label + 3 Installation: * Flash the factory image by TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to WAX214v2 GPL source: https://www.downloads.netgear.com/files/GPL/WAX214v2-V1.0.1.5-gpl-src.tar.gz * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax214v2.dts DTS file for this device. Signed-off-by: Borys Zhukov <borys@zhukov.org> Link: https://github.com/openwrt/openwrt/pull/14401 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Borys Zhukov
Hauke Mehrtens
parent
403c17cadf
commit
f25cd55bd1
@ -146,6 +146,10 @@ xiaomi,mi-router-cr6608|\
|
||||
xiaomi,mi-router-cr6609)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
|
||||
;;
|
||||
netgear,wax214v2)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
ubootenv_add_uci_sys_config "/dev/mtd1" "0x20000" "0x8000" "0x20000"
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
|
||||
228
target/linux/ramips/dts/mt7621_netgear_wax214v2.dts
Normal file
228
target/linux/ramips/dts/mt7621_netgear_wax214v2.dts
Normal file
@ -0,0 +1,228 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "netgear,wax214v2", "mediatek,mt7621-soc";
|
||||
model = "Netgear WAX214v2";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_amber;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_blue;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_green: power_green {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_blue: power_blue {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_amber: power_amber {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifin_green {
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0radio";
|
||||
};
|
||||
|
||||
wifia_green {
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1radio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "Config";
|
||||
reg = <0x80000 0x80000>;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "Factory";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0xe00>;
|
||||
};
|
||||
|
||||
precal_factory_e10: precal@e10 {
|
||||
reg = <0xe10 0x19c10>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x2600000>;
|
||||
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "kernel";
|
||||
reg = <0x0 0x400000>;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "ubi";
|
||||
reg = <0x400000 0x2200000>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@2780000 {
|
||||
label = "firmware_backup";
|
||||
reg = <0x2780000 0x2600000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@4d80000 {
|
||||
label = "CFG";
|
||||
reg = <0x4d80000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5580000 {
|
||||
label = "RAE";
|
||||
reg = <0x5580000 0x400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5980000 {
|
||||
label = "POT";
|
||||
reg = <0x5980000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5a80000 {
|
||||
label = "Language";
|
||||
reg = <0x5a80000 0x400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5e80000 {
|
||||
label = "Traffic";
|
||||
reg = <0x5e80000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6080000 {
|
||||
label = "Cert";
|
||||
reg = <0x6080000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6180000 {
|
||||
label = "NTGRcryptK";
|
||||
reg = <0x6180000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6280000 {
|
||||
label = "NTGRcryptD";
|
||||
reg = <0x6280000 0x500000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6780000 {
|
||||
label = "LOG";
|
||||
reg = <0x6780000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6880000 {
|
||||
label = "User_data";
|
||||
reg = <0x6880000 0x640000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_0>, <&precal_factory_e10>;
|
||||
nvmem-cell-names = "eeprom", "precal";
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "uart3", "uart2", "jtag";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
status = "okay";
|
||||
label = "lan";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "disabled";
|
||||
};
|
||||
@ -2113,6 +2113,24 @@ define Device/netgear_wax202
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wax202
|
||||
|
||||
define Device/netgear_wax214v2
|
||||
$(Device/nand)
|
||||
DEVICE_VENDOR := NETGEAR
|
||||
DEVICE_MODEL := WAX214v2
|
||||
DEVICE_PACKAGES := kmod-mt7915-firmware
|
||||
NETGEAR_ENC_MODEL := WAX214v2
|
||||
NETGEAR_ENC_REGION := US
|
||||
IMAGE_SIZE := 38912k
|
||||
KERNEL_LOADADDR := 0x82000000
|
||||
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
||||
append-squashfs4-fakeroot
|
||||
IMAGES += factory.img
|
||||
IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
||||
append-ubi | check-size | netgear-encrypted-factory
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wax214v2
|
||||
|
||||
define Device/netgear_wndr3700-v5
|
||||
$(Device/dsa-migration)
|
||||
$(Device/netgear_sercomm_nor)
|
||||
|
||||
@ -47,6 +47,7 @@ ramips_setup_interfaces()
|
||||
mikrotik,routerboard-m11g|\
|
||||
netgear,eax12|\
|
||||
netgear,ex6150|\
|
||||
netgear,wax214v2|\
|
||||
sercomm,na502|\
|
||||
sercomm,na502s|\
|
||||
thunder,timecloud|\
|
||||
@ -325,6 +326,10 @@ ramips_setup_macs()
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
netgear,wax214v2)
|
||||
lan_mac=$(mtd_get_mac_ascii Config ethaddr)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
yuncore,ax820)
|
||||
label_mac=$(mtd_get_mac_binary Factory 0x4)
|
||||
;;
|
||||
|
||||
@ -153,6 +153,11 @@ case "$board" in
|
||||
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 3 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
netgear,wax214v2)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii Config ethaddr)
|
||||
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 3 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
mercusys,mr70x-v1|\
|
||||
tplink,archer-ax23-v1)
|
||||
hw_mac_addr="$(mtd_get_mac_binary config 0x8)"
|
||||
|
||||
@ -122,6 +122,7 @@ platform_do_upgrade() {
|
||||
netgear,wac104|\
|
||||
netgear,wac124|\
|
||||
netgear,wax202|\
|
||||
netgear,wax214v2|\
|
||||
netis,wf2881|\
|
||||
raisecom,msg1500-x-00|\
|
||||
rostelecom,rt-fe-1a|\
|
||||
|
||||
Loading…
Reference in New Issue
Block a user