mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-11 17:34:57 +00:00
ipq40xx: add support for Plasma Cloud PA1200
Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
This commit is contained in:
parent
8a891bfaa0
commit
ea5bb6bbfe
@ -36,7 +36,8 @@ edgecore,ecw5211 |\
|
||||
glinet,gl-b1300 |\
|
||||
luma,wrtq-329acn |\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62)
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200)
|
||||
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
buffalo,wtr-m2133hp)
|
||||
|
@ -42,6 +42,7 @@ ALLWIFIBOARDS:= \
|
||||
linksys_mr8300-v0 \
|
||||
luma_wrtq-329acn \
|
||||
mobipromo_cm520-79f \
|
||||
plasmacloud_pa1200 \
|
||||
qxwlan_e2600ac
|
||||
|
||||
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
||||
@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
|
||||
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
|
||||
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
|
||||
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
|
||||
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
|
||||
|
||||
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|
||||
|
BIN
package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019
Normal file
BIN
package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019
Normal file
Binary file not shown.
@ -7,7 +7,7 @@
|
||||
#
|
||||
|
||||
usage() {
|
||||
echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300> <out file path> <kernel path> <rootfs path>"
|
||||
echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300|PA1200> <out file path> <kernel path> <rootfs path>"
|
||||
rm -f $CFG_OUT
|
||||
exit 1
|
||||
}
|
||||
@ -33,7 +33,7 @@ case $CE_TYPE in
|
||||
SIZE_FACTOR=1
|
||||
SIZE_FORMAT="%d"
|
||||
;;
|
||||
A42)
|
||||
A42|PA1200)
|
||||
MAX_PART_SIZE=15616
|
||||
KERNEL_FLASH_ADDR=0x180000
|
||||
SIZE_FACTOR=1024
|
||||
|
@ -17,7 +17,8 @@ ipq40xx_setup_interfaces()
|
||||
alfa-network,ap120c-ac|\
|
||||
engenius,emr3500|\
|
||||
engenius,ens620ext|\
|
||||
luma,wrtq-329acn)
|
||||
luma,wrtq-329acn|\
|
||||
plasmacloud,pa1200)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
;;
|
||||
aruba,ap-303|\
|
||||
|
@ -101,6 +101,7 @@ case "$FIRMWARE" in
|
||||
luma,wrtq-329acn|\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2 |\
|
||||
unielec,u4019-32m)
|
||||
@ -198,6 +199,7 @@ case "$FIRMWARE" in
|
||||
luma,wrtq-329acn|\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2 |\
|
||||
unielec,u4019-32m)
|
||||
|
@ -44,6 +44,7 @@ platform_do_upgrade_dualboot_datachk() {
|
||||
# boot anymore to Linux until it was reflashed with ap51-flash.
|
||||
local next_boot_part="1"
|
||||
case "$(board_name)" in
|
||||
plasmacloud,pa1200|\
|
||||
openmesh,a42)
|
||||
primary_kernel_mtd=8
|
||||
;;
|
||||
|
@ -111,7 +111,8 @@ platform_do_upgrade() {
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
openmesh,a42 |\
|
||||
openmesh,a62)
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_dualboot_datachk "$1"
|
||||
;;
|
||||
|
@ -0,0 +1,197 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
|
||||
* Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Plasma Cloud PA1200";
|
||||
compatible = "plasmacloud,pa1200";
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_purple;
|
||||
led-failsafe = &led_status_yellow;
|
||||
led-running = &led_status_cyan;
|
||||
led-upgrade = &led_status_yellow;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_cyan: status_cyan {
|
||||
label = "cyan:status";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_purple: status_purple {
|
||||
label = "purple:status";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_yellow: status_yellow {
|
||||
label = "yellow:status";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
/* partitions are passed via bootloader */
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <2 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
|
||||
};
|
@ -648,6 +648,22 @@ define Device/openmesh_a62
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a62
|
||||
|
||||
define Device/plasmacloud_pa1200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Plasma Cloud
|
||||
DEVICE_MODEL := PA1200
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@pc.pa1200
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15616k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := uboot-envtools ipq-wifi-plasmacloud-pa1200
|
||||
endef
|
||||
TARGET_DEVICES += plasmacloud_pa1200
|
||||
|
||||
define Device/qcom_ap-dk01.1-c1
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK01.1
|
||||
|
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -837,11 +837,54 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -837,11 +837,55 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4018-meshpoint-one.dtb \
|
||||
+ qcom-ipq4018-nbg6617.dtb \
|
||||
+ qcom-ipq4019-oap100.dtb \
|
||||
+ qcom-ipq4018-pa1200.dtb \
|
||||
+ qcom-ipq4018-rt-ac58u.dtb \
|
||||
+ qcom-ipq4018-wre6606.dtb \
|
||||
+ qcom-ipq4018-wrtq-329acn.dtb \
|
||||
|
Loading…
Reference in New Issue
Block a user