ath79: add support for Siemens WS-AP3610
Hardware
--------
SoC: Atheros AR7161
RAM: Samsung K4H511638D-UCCC
2x 64M DDR1
SPI: Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
Atheros AR9160 an
ETH: Broadcom BCM5481
LED: Power (Green/Red)
ETH (Green / Blue / Yellow)
(PHY-controlled)
WiFi 5 (Green / Blue)
WiFi 2 (Green / Blue)
BTN: Reset
Serial: Cisco-Style RJ45 - 115200 8N1
Installation
------------
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot; bootm'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
David Bauer
parent
ae35ff5767
commit
d2b8ccb1c0
|
|
@ -0,0 +1,186 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar7100.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "siemens,ws-ap3610", "qca,ar7161";
|
||||
model = "Siemens WS-AP3610";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_red;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
extosc: ref {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-output-names = "ref";
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_green: led_power_green {
|
||||
label = "ws-ap3610:green:power";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_red: led_power_red {
|
||||
label = "ws-ap3610:red:power";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan5_blue {
|
||||
label = "ws-ap3610:blue:wlan5";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led_wlan5_green {
|
||||
label = "ws-ap3610:green:wlan5";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan2_blue {
|
||||
label = "ws-ap3610:blue:wlan2";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
led_wlan2_green {
|
||||
label = "ws-ap3610:green:wlan2";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
/*
|
||||
* When the compatible-is missing, PHY autodetection
|
||||
* is performed, but the PHY-ID reads all 0xff.
|
||||
*
|
||||
* Linux does not create the device in this case,
|
||||
* and the reset is never even de-asserted.
|
||||
*/
|
||||
compatible = "ethernet-phy-id0143.bca2",
|
||||
"ethernet-phy-ieee802.3-c22";
|
||||
reg = <0>;
|
||||
|
||||
resets = <&rst 8>;
|
||||
reset-names = "phy";
|
||||
reset-assert-us = <10000>;
|
||||
reset-deassert-us = <10000>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii-id";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-bak";
|
||||
reg = <0x40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x80000 0xe00000>;
|
||||
};
|
||||
|
||||
partition@e80000 {
|
||||
label = "cfg1";
|
||||
reg = <0xe80000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ec0000 {
|
||||
label = "cfg2";
|
||||
reg = <0xec0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
label = "nvram1";
|
||||
reg = <0xf00000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f40000 {
|
||||
label = "nvram2";
|
||||
reg = <0xf40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f80000 {
|
||||
label = "rsvd1";
|
||||
reg = <0xf80000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fc0000 {
|
||||
label = "rsvd2";
|
||||
reg = <0xfc0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -30,6 +30,7 @@ ath79_setup_interfaces()
|
|||
pisen,ts-d084|\
|
||||
pisen,wmb001n|\
|
||||
pisen,wmm003n|\
|
||||
siemens,ws-ap3610|\
|
||||
tplink,cpe210-v2|\
|
||||
tplink,cpe210-v3|\
|
||||
tplink,cpe510-v2|\
|
||||
|
|
|
|||
|
|
@ -34,6 +34,9 @@ case "$board" in
|
|||
[ "$PHYNBR" -eq 1 ] && \
|
||||
k2t_get_mac "lan_mac" > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
siemens,ws-ap3610)
|
||||
mtd_get_mac_ascii cfg1 RADIOADDR${PHYNBR} > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
trendnet,tew-823dru)
|
||||
# set the 2.4G interface mac address to LAN MAC
|
||||
[ "$PHYNBR" -eq 1 ] && \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,13 @@
|
|||
#!/bin/sh
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
preinit_set_mac_address() {
|
||||
case $(board_name) in
|
||||
siemens,ws-ap3610)
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii cfg1 ethaddr)
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
boot_hook_add preinit_main preinit_set_mac_address
|
||||
|
|
@ -1,4 +1,5 @@
|
|||
CONFIG_AT803X_PHY=y
|
||||
CONFIG_BROADCOM_PHY=y
|
||||
CONFIG_GPIO_WATCHDOG=y
|
||||
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
||||
CONFIG_INTEL_XWAY_PHY=y
|
||||
|
|
|
|||
|
|
@ -1041,6 +1041,20 @@ define Device/rosinson_wr818
|
|||
endef
|
||||
TARGET_DEVICES += rosinson_wr818
|
||||
|
||||
define Device/siemens_ws-ap3610
|
||||
SOC := ar7161
|
||||
DEVICE_VENDOR := Siemens
|
||||
DEVICE_MODEL := WS-AP3610
|
||||
IMAGE_SIZE := 14336k
|
||||
LOADER_TYPE := bin
|
||||
LOADER_FLASH_OFFS := 0x82000
|
||||
COMPILE := loader-$(1).bin
|
||||
COMPILE/loader-$(1).bin := loader-okli-compile
|
||||
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
|
||||
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
|
||||
endef
|
||||
TARGET_DEVICES += siemens_ws-ap3610
|
||||
|
||||
define Device/sitecom_wlr-7100
|
||||
SOC := ar1022
|
||||
DEVICE_VENDOR := Sitecom
|
||||
|
|
|
|||
Loading…
Reference in New Issue