mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-29 10:02:23 +00:00
ath79: add support for Teltonika RUT955
Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by 74HC595) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector Serial console (/dev/ttyS0) pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2". Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Daniel Golle
parent
e5e461b621
commit
d1130ad265
346
target/linux/ath79/dts/ar9344_teltonika_rut955.dts
Normal file
346
target/linux/ath79/dts/ar9344_teltonika_rut955.dts
Normal file
@ -0,0 +1,346 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Teltonika RUT955";
|
||||
compatible = "teltonika,rut955", "qca,ar9344";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart;
|
||||
serial1 = &hs_uart;
|
||||
led-boot = &led_system_green;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_system_green;
|
||||
led-upgrade = &led_system_red;
|
||||
label-mac-device = ð1;
|
||||
};
|
||||
|
||||
i2c {
|
||||
compatible = "i2c-gpio";
|
||||
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hwmon@4d {
|
||||
compatible = "microchip,mcp3221";
|
||||
reg = <0x4d>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
signal1 {
|
||||
label = "rut955:green:signal1";
|
||||
gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal2 {
|
||||
label = "rut955:green:signal2";
|
||||
gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal3 {
|
||||
label = "rut955:green:signal3";
|
||||
gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal4 {
|
||||
label = "rut955:green:signal4";
|
||||
gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal5 {
|
||||
label = "rut955:green:signal5";
|
||||
gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_red: system_red {
|
||||
label = "rut955:red:system";
|
||||
gpios = <&gpio_ext 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_green: system_green {
|
||||
label = "rut955:green:system";
|
||||
gpios = <&gpio_ext 6 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
gpio-line-names = "RS485_D", "led_wan", "DIN3", "mmc_cs",
|
||||
"ext_sck", "", "", "",
|
||||
"", "", "", "",
|
||||
"ext_mosi", "led_lan2", "led_lan1", "",
|
||||
"i2c_scl", "i2c_sda", "", "DIN2",
|
||||
"ext_cs", "DIN1", "led_lan3", "",
|
||||
"", "", "", "",
|
||||
"", "", "", "";
|
||||
|
||||
ext_sck {
|
||||
gpio-hog;
|
||||
gpios = <4 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:ext:sck";
|
||||
};
|
||||
|
||||
ext_mosi {
|
||||
gpio-hog;
|
||||
gpios = <12 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:ext:mosi";
|
||||
};
|
||||
|
||||
ext_cs {
|
||||
gpio-hog;
|
||||
gpios = <20 GPIO_ACTIVE_HIGH>;
|
||||
output-low;
|
||||
line-name = "rut955:ext:cs";
|
||||
};
|
||||
|
||||
mmc_cs {
|
||||
gpio-hog;
|
||||
gpios = <3 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:mmc:cs";
|
||||
};
|
||||
|
||||
uart1_td {
|
||||
gpio-hog;
|
||||
gpios = <18 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:uart1:td";
|
||||
};
|
||||
|
||||
uart1_rd {
|
||||
gpio-hog;
|
||||
gpios = <11 GPIO_ACTIVE_LOW>;
|
||||
input;
|
||||
line-name = "rut955:uart1:rd";
|
||||
};
|
||||
|
||||
led_wan {
|
||||
gpio-hog;
|
||||
gpios = <1 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:led:wan";
|
||||
};
|
||||
|
||||
led_lan2 {
|
||||
gpio-hog;
|
||||
gpios = <13 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:led:lan2";
|
||||
};
|
||||
|
||||
led_lan1 {
|
||||
gpio-hog;
|
||||
gpios = <14 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:led:lan1";
|
||||
};
|
||||
|
||||
led_lan3 {
|
||||
gpio-hog;
|
||||
gpios = <22 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "rut955:led:lan3";
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_uart {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_uart2>;
|
||||
|
||||
rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
rs485-rts-active-low;
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <3>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_spi>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
config: partition@20000 {
|
||||
label = "config";
|
||||
reg = <0x20000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@30000 {
|
||||
label = "art";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "firmware";
|
||||
reg = <0x40000 0xf30000>;
|
||||
compatible = "tplink,firmware";
|
||||
};
|
||||
|
||||
partition@f70000 {
|
||||
label = "event-log";
|
||||
reg = <0xf70000 0x90000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
microsd@1 {
|
||||
status = "disabled";
|
||||
|
||||
compatible = "mmc-spi-slot";
|
||||
spi-max-frequency = <25000000>;
|
||||
reg = <1>;
|
||||
voltage-ranges = <3200 3400>;
|
||||
broken-cd;
|
||||
};
|
||||
|
||||
gpio_ext: gpio_ext@2 {
|
||||
compatible = "fairchild,74hc595";
|
||||
reg = <2>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <2>;
|
||||
spi-max-frequency = <10000000>;
|
||||
gpio-line-names = "led_signal_bar1", "led_signal_bar2", "led_signal_bar3", "led_signal_bar4",
|
||||
"led_signal_bar5", "led_status_red", "led_status_green", "sim_sel",
|
||||
"DOUT1", "DOUT2", "modem_vbus", "modem_rst",
|
||||
"DOUT3", "RS485_R", "SDCS", "HWRST";
|
||||
};
|
||||
};
|
||||
|
||||
&usb {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
port@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
|
||||
port@1 {
|
||||
compatible = "usb-a-connector";
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
label = "RS-232 serial adapter";
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
port@4 {
|
||||
label = "internal wwan modem";
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&config 0x0>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
|
||||
mtd-mac-address = <&config 0x0>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&config 0x0>;
|
||||
};
|
||||
|
||||
&builtin_switch {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_leds_switch>;
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
pmx_spi: spi {
|
||||
// SPI_CS1 on GPIO 3, 2nd SCK on GPIO 4
|
||||
// 2nd MOSI on GPIO 12, SPI_CS2 on GPIO 20
|
||||
pinctrl-single,bits = <0x0 0x07000000 0xff000000>,
|
||||
<0x4 0x0a 0xff>,
|
||||
<0xc 0x0b 0xff>,
|
||||
<0x14 0x08 0xff>;
|
||||
};
|
||||
|
||||
pmx_leds_switch: leds_switch {
|
||||
// switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
|
||||
pinctrl-single,bits = <0x0 0x00002d00 0x0000ff00>,
|
||||
<0xc 0x002c2b00 0x00ffff00>,
|
||||
<0x14 0x002a0000 0x00ff0000>;
|
||||
};
|
||||
|
||||
pmx_uart2: uart2 {
|
||||
// UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
|
||||
pinctrl-single,bits = <0x0 0x0 0xff>,
|
||||
<0x10 0x4f000000 0xff000000>,
|
||||
<0x3c 0x000b0000 0x00ff0000>;
|
||||
};
|
||||
};
|
||||
@ -220,6 +220,11 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:wan"
|
||||
;;
|
||||
teltonika,rut955)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-c6-v2|\
|
||||
tplink,archer-c6-v2-us|\
|
||||
|
||||
@ -38,6 +38,14 @@ dlink,dir-835-a1)
|
||||
librerouter,librerouter-v1)
|
||||
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "1" "0"
|
||||
;;
|
||||
teltonika,rut955)
|
||||
ucidef_add_gpio_switch "sim_sel" "SIM select" "503" "1"
|
||||
ucidef_add_gpio_switch "DOUT1" "DOUT1 (OC)" "504" "0"
|
||||
ucidef_add_gpio_switch "DOUT2" "DOUT2 (Relay)" "505" "0"
|
||||
ucidef_add_gpio_switch "modem_vbus" "Modem enable" "506" "1"
|
||||
ucidef_add_gpio_switch "modem_rst" "Modem reset" "507" "0"
|
||||
ucidef_add_gpio_switch "DOUT3" "DOUT3" "508" "0"
|
||||
;;
|
||||
tplink,archer-c25-v1)
|
||||
ucidef_add_gpio_switch "led_control" "LED control" "21" "0"
|
||||
ucidef_add_gpio_switch "led_reset" "LED reset" "19" "1"
|
||||
|
||||
@ -36,6 +36,11 @@ define Build/addpattern
|
||||
-mv "$@.new" "$@"
|
||||
endef
|
||||
|
||||
define Build/append-md5sum-bin
|
||||
$(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
|
||||
xargs echo -ne >> $@
|
||||
endef
|
||||
|
||||
define Build/cybertan-trx
|
||||
@echo -n '' > $@-empty.bin
|
||||
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
|
||||
@ -73,6 +78,17 @@ define Build/pisen_wmb001n-factory
|
||||
rm -rf "$@.tmp"
|
||||
endef
|
||||
|
||||
define Build/teltonika-fw-fake-checksum
|
||||
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
|
||||
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
|
||||
# from begin of the firmware file) with 16 bytes stored just before
|
||||
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
|
||||
let \
|
||||
offs="$$(stat -c%s $@) - 20"; \
|
||||
dd if=$@ bs=1 count=16 skip=76 |\
|
||||
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
|
||||
endef
|
||||
|
||||
define Device/seama
|
||||
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
||||
@ -1070,6 +1086,28 @@ define Device/sitecom_wlr-7100
|
||||
endef
|
||||
TARGET_DEVICES += sitecom_wlr-7100
|
||||
|
||||
define Device/teltonika_rut955
|
||||
SOC := ar9344
|
||||
DEVICE_VENDOR := Teltonika
|
||||
DEVICE_MODEL := RUT955
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
|
||||
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
|
||||
IMAGE_SIZE := 15552k
|
||||
TPLINK_HWID := 0x35000001
|
||||
TPLINK_HWREV := 0x1
|
||||
TPLINK_HEADER_VERSION := 1
|
||||
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
|
||||
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
|
||||
pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
|
||||
append-md5sum-bin | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
|
||||
append-rootfs | pad-rootfs | append-metadata |\
|
||||
check-size $$$$(IMAGE_SIZE)
|
||||
endef
|
||||
TARGET_DEVICES += teltonika_rut955
|
||||
|
||||
define Device/trendnet_tew-823dru
|
||||
SOC := qca9558
|
||||
DEVICE_VENDOR := Trendnet
|
||||
|
||||
Loading…
Reference in New Issue
Block a user