ramips: add support for Cudy WR1300
Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7612E - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB - Power: DC 12V 1A tip positive UART Serial: 115200 baud Located on unpopulated 4 pin header near J4: J4 [o] Rx [o] Tx [o] GND [ ] Vcc - Do not connect Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html MAC addresses as verified by OEM firmware: use address source LAN *:f0 label WAN *:f1 label + 1 2g *:f0 label 5g *:f2 label + 2 The label MAC address is found in bdinfo 0xde00. Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
This commit is contained in:
Andrew Pikler
Adrian Schmutzler
parent
dc4745da7a
commit
cd2b661453
|
|
@ -0,0 +1,195 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
compatible = "cudy,wr1300", "mediatek,mt7621-soc";
|
||||
model = "Cudy WR1300";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_sys;
|
||||
led-failsafe = &led_sys;
|
||||
led-running = &led_sys;
|
||||
led-upgrade = &led_sys;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_sys: sys {
|
||||
label = "green:sys";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "green:usb";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "green:wps";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <80000000>;
|
||||
m25p,fast-read;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x50000 0xf80000>;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "debug";
|
||||
reg = <0xfd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "backup";
|
||||
reg = <0xfe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
bdinfo: partition@ff0000 {
|
||||
label = "bdinfo";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
compatible = "pci14c3,7603";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0000>;
|
||||
mtd-mac-address = <&bdinfo 0xde00>;
|
||||
ieee80211-freq-limit = <2400000 2500000>;
|
||||
|
||||
led {
|
||||
led-active-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "pci14c3,7662";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x8000>;
|
||||
mtd-mac-address = <&bdinfo 0xde00>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
|
||||
led {
|
||||
led-sources = <2>;
|
||||
led-active-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
mtd-mac-address = <&bdinfo 0xde00>;
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
status = "okay";
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
status = "okay";
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
status = "okay";
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
status = "okay";
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
status = "okay";
|
||||
label = "wan";
|
||||
mtd-mac-address = <&bdinfo 0xde00>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "wdt", "i2c", "jtag";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
|
@ -222,6 +222,16 @@ define Device/buffalo_wsr-600dhp
|
|||
endef
|
||||
TARGET_DEVICES += buffalo_wsr-600dhp
|
||||
|
||||
define Device/cudy_wr1300
|
||||
$(Device/dsa-migration)
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := WR1300
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
|
||||
kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += cudy_wr1300
|
||||
|
||||
define Device/dlink_dir-8xx-a1
|
||||
$(Device/dsa-migration)
|
||||
IMAGE_SIZE := 16000k
|
||||
|
|
|
|||
Loading…
Reference in New Issue