mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-02-16 20:07:23 +00:00
ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)
This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Anderson Vulczak
Adrian Schmutzler
parent
c08ddfce3f
commit
9b90dc05f5
130
target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts
Normal file
130
target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts
Normal file
@ -0,0 +1,130 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "qca9563_tplink_archer-x6-v2.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,archer-c6-v2-us", "qca,qca9563";
|
||||
model = "TP-Link Archer C6 v2 (US) / A6 v2 (US/TW)";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "tp-link:green:wlan2g";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "tp-link:green:wan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_fail {
|
||||
label = "tp-link:amber:wan";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "tp-link:green:wps";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "WPS button";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "factory-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
mac: partition@20000 {
|
||||
label = "mac";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot";
|
||||
reg = <0x030000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x050000 0xf80000>;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "tplink";
|
||||
reg = <0xfd0000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -5,5 +5,120 @@
|
||||
|
||||
/ {
|
||||
compatible = "tplink,archer-c6-v2", "qca,qca9563";
|
||||
model = "TP-Link Archer C6 v2";
|
||||
model = "TP-Link Archer C6 v2 (EU/RU/JP)";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "tp-link:green:wlan2g";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "tp-link:green:wan";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_fail {
|
||||
label = "tp-link:amber:wan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "tp-link:green:wps";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "WPS button";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
mac: partition@20000 {
|
||||
label = "mac";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x030000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@7d0000 {
|
||||
label = "tplink";
|
||||
reg = <0x7d0000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -1,5 +1,4 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
@ -7,76 +6,12 @@
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "tp-link:green:wlan2g";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "tp-link:green:wan";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_fail {
|
||||
label = "tp-link:amber:wan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "tp-link:green:wps";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "WPS button";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
};
|
||||
|
||||
@ -92,54 +27,6 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
mac: partition@20000 {
|
||||
label = "mac";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x030000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@7d0000 {
|
||||
label = "tplink";
|
||||
reg = <0x7d0000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
@ -161,8 +48,9 @@
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
mtd-mac-address = <&mac 0x8>;
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
mtd-mac-address = <&mac 0x8>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
|
||||
@ -146,7 +146,8 @@ tplink,tl-wr1043n-v5)
|
||||
ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x04"
|
||||
ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x02"
|
||||
;;
|
||||
tplink,archer-c6-v2)
|
||||
tplink,archer-c6-v2|\
|
||||
tplink,archer-c6-v2-us)
|
||||
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C"
|
||||
ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02"
|
||||
;;
|
||||
|
||||
@ -207,6 +207,7 @@ ath79_setup_interfaces()
|
||||
;;
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-c6-v2|\
|
||||
tplink,archer-c6-v2-us|\
|
||||
tplink,archer-c7-v4|\
|
||||
tplink,archer-c7-v5|\
|
||||
tplink,tl-wdr3600-v1|\
|
||||
|
||||
@ -146,7 +146,8 @@ case "$FIRMWARE" in
|
||||
tplink,archer-c59-v2|\
|
||||
tplink,archer-c60-v1|\
|
||||
tplink,archer-c60-v2|\
|
||||
tplink,archer-c6-v2)
|
||||
tplink,archer-c6-v2|\
|
||||
tplink,archer-c6-v2-us)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
|
||||
@ -88,12 +88,26 @@ define Device/tplink_archer-c6-v2
|
||||
ATH_SOC := qca9563
|
||||
IMAGE_SIZE := 7808k
|
||||
DEVICE_MODEL := Archer C6
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_VARIANT := v2 (EU/RU/JP)
|
||||
TPLINK_BOARD_ID := ARCHER-C6-V2
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c6-v2
|
||||
|
||||
define Device/tplink_archer-c6-v2-us
|
||||
$(Device/tplink-safeloader-uimage)
|
||||
ATH_SOC := qca9563
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_MODEL := Archer C6
|
||||
DEVICE_VARIANT := v2 (US)
|
||||
DEVICE_ALT0_VENDOR := TP-Link
|
||||
DEVICE_ALT0_MODEL := Archer A6
|
||||
DEVICE_ALT0_VARIANT := v2 (US/TW)
|
||||
TPLINK_BOARD_ID := ARCHER-C6-V2-US
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c6-v2-us
|
||||
|
||||
define Device/tplink_archer-c60-v1
|
||||
$(Device/tplink-safeloader-uimage)
|
||||
ATH_SOC := qca9561
|
||||
|
||||
@ -881,7 +881,7 @@ static struct device_info boards[] = {
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
/** Firmware layout for the C6v2 */
|
||||
/** Firmware layout for the Archer C6 v2 (EU/RU/JP) */
|
||||
{
|
||||
.id = "ARCHER-C6-V2",
|
||||
.vendor = "",
|
||||
@ -916,6 +916,40 @@ static struct device_info boards[] = {
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
/** Firmware layout for the Archer C6 v2 (US) and A6 v2 (US/TW) */
|
||||
{
|
||||
.id = "ARCHER-C6-V2-US",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\n"
|
||||
"{product_name:Archer A6,product_ver:2.0.0,special_id:55530000}\n"
|
||||
"{product_name:Archer A6,product_ver:2.0.0,special_id:54570000}\n"
|
||||
"{product_name:Archer C6,product_ver:2.0.0,special_id:55530000}\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = "soft_ver:1.1.1\n",
|
||||
|
||||
.partitions = {
|
||||
{"factory-boot", 0x00000, 0x20000},
|
||||
{"default-mac", 0x20000, 0x00200},
|
||||
{"pin", 0x20200, 0x00100},
|
||||
{"product-info", 0x20300, 0x00200},
|
||||
{"device-id", 0x20500, 0x0fb00},
|
||||
{"fs-uboot", 0x30000, 0x20000},
|
||||
{"firmware", 0x50000, 0xf89400},
|
||||
{"soft-version", 0xfd9400, 0x00100},
|
||||
{"extra-para", 0xfd9500, 0x00100},
|
||||
{"support-list", 0xfd9600, 0x00200},
|
||||
{"profile", 0xfd9800, 0x03000},
|
||||
{"default-config", 0xfdc800, 0x03000},
|
||||
{"partition-table", 0xfdf800, 0x00800},
|
||||
{"user-config", 0xfe0000, 0x0c000},
|
||||
{"certificate", 0xfec000, 0x04000},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
/** Firmware layout for the C60v1 */
|
||||
{
|
||||
@ -2069,6 +2103,9 @@ static void build_image(const char *output,
|
||||
} else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) {
|
||||
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00};
|
||||
parts[5] = put_data("extra-para", mdat, 11);
|
||||
} else if (strcasecmp(info->id, "ARCHER-C6-V2-US") == 0) {
|
||||
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00};
|
||||
parts[5] = put_data("extra-para", mdat, 11);
|
||||
}
|
||||
|
||||
size_t len;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user