mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-25 16:13:05 +00:00
ath79: support for TP-Link EAP225-Outdoor v3
This model is almost identical to the EAP225-Outdoor v1. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de> Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de> Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de> [Add pre-calibraton nvme-cells] Tested-by: Tido Klaassen <tido_ff@4gh.eu> Signed-off-by: Nick Hainke <vincent@systemli.org>
This commit is contained in:
parent
8bd5bbad1e
commit
7e4de89e63
59
target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts
Normal file
59
target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts
Normal file
@ -0,0 +1,59 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9563_tplink_eap2x5-1port.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,eap225-outdoor-v3", "qca,qca9563";
|
||||
model = "TP-Link EAP225-Outdoor v3";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_amber;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_amber;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_green: status_green {
|
||||
label = "green:status";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led_status_amber: status_amber {
|
||||
label = "amber:status";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&art {
|
||||
precalibration_ath10k: pre-calibration@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
phy-handle = <&phy6>;
|
||||
phy-mode = "sgmii";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
phy6: ethernet-phy@6 {
|
||||
reg = <6>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0 0 0 0 0>;
|
||||
|
||||
mac-address-increment = <1>;
|
||||
|
||||
nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>;
|
||||
nvmem-cell-names = "mac-address", "pre-calibration";
|
||||
};
|
||||
};
|
@ -76,6 +76,7 @@ ath79_setup_interfaces()
|
||||
tplink,cpe610-v2|\
|
||||
tplink,cpe710-v1|\
|
||||
tplink,eap225-outdoor-v1|\
|
||||
tplink,eap225-outdoor-v3|\
|
||||
tplink,eap225-v1|\
|
||||
tplink,eap225-v3|\
|
||||
tplink,eap245-v1|\
|
||||
|
@ -401,6 +401,17 @@ define Device/tplink_eap225-outdoor-v1
|
||||
endef
|
||||
TARGET_DEVICES += tplink_eap225-outdoor-v1
|
||||
|
||||
define Device/tplink_eap225-outdoor-v3
|
||||
$(Device/tplink-eap2x5)
|
||||
SOC := qca9563
|
||||
IMAGE_SIZE := 13824k
|
||||
DEVICE_MODEL := EAP225-Outdoor
|
||||
DEVICE_VARIANT := v3
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
TPLINK_BOARD_ID := EAP225-V3
|
||||
endef
|
||||
TARGET_DEVICES += tplink_eap225-outdoor-v3
|
||||
|
||||
define Device/tplink_eap225-v1
|
||||
$(Device/tplink-eap2x5)
|
||||
SOC := qca9563
|
||||
|
Loading…
Reference in New Issue
Block a user