ath79: add support for WD My Net N750
SoC: AR9344 RAM: 128MB Flash: 16MiB Winbond 25Q128BVFG SPI NOR 5GHz WiFi: AR9380 PCIe 3x3:3 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Gigabit ethernet via AR8327N switch (green + amber LEDs) 2x USB 2.0 via GL850G hub 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO Known issues: AR8327N LEDs only have default functionality, not presented in sysfs. This is a regression from ar71xx. UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX See https://openwrt.org/toh/wd/n750 for flashing detail. Procedures unchanged from ar71xx. Tested sysupgrade + factory flash from WD Emergency Recovery Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This commit is contained in:
Ryan Mounce
Petr Štetiar
parent
7d77879236
commit
6d6985ff0e
|
|
@ -126,7 +126,8 @@ ath79_setup_interfaces()
|
|||
iodata,wn-ac1600dgr|\
|
||||
iodata,wn-ac1600dgr2|\
|
||||
iodata,wn-ag300dgr|\
|
||||
pcs,cr5000)
|
||||
pcs,cr5000|\
|
||||
wd,mynet-n750)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
;;
|
||||
|
|
@ -290,7 +291,8 @@ ath79_setup_macs()
|
|||
wan_mac=$(mtd_get_mac_text "mac" 24)
|
||||
;;
|
||||
dlink,dir-859-a1|\
|
||||
nec,wg1200cr)
|
||||
nec,wg1200cr|\
|
||||
wd,mynet-n750)
|
||||
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
|
||||
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -105,7 +105,9 @@ case "$FIRMWARE" in
|
|||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
dlink,dir-859-a1|\
|
||||
nec,wg1200cr|\
|
||||
wd,mynet-n750)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
|
||||
;;
|
||||
|
|
@ -121,10 +123,6 @@ case "$FIRMWARE" in
|
|||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
|
||||
;;
|
||||
nec,wg1200cr)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata wlan24mac) 2
|
||||
;;
|
||||
nec,wg800hp)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2
|
||||
|
|
@ -184,6 +182,10 @@ case "$FIRMWARE" in
|
|||
ubnt,unifi)
|
||||
ath9k_eeprom_extract "art" 4096 2048
|
||||
;;
|
||||
wd,mynet-n750)
|
||||
ath9k_eeprom_extract "art" 20480 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan5mac") 2
|
||||
;;
|
||||
wd,mynet-wifi-rangeextender)
|
||||
ath9k_eeprom_extract "art" 4096 4096
|
||||
ath9k_patch_fw_mac_crc $(nvram get wl0_hwaddr) "$mac" 2
|
||||
|
|
|
|||
|
|
@ -12,6 +12,9 @@ engenius,epg5000)
|
|||
tplink,archer-c7-v5)
|
||||
migrate_leds "archer-c7-v5:=tp-link:"
|
||||
;;
|
||||
wd,mynet-n750)
|
||||
migrate_leds "wd:=mynet-n750:"
|
||||
;;
|
||||
esac
|
||||
|
||||
migrations_apply system
|
||||
|
|
|
|||
|
|
@ -0,0 +1,216 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Western Digital My Net N750";
|
||||
compatible = "wd,mynet-n750", "qca,ar9344";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wifi {
|
||||
label = "mynet-n750:blue:wireless";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet {
|
||||
label = "mynet-n750:blue:internet";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "mynet-n750:blue:wps";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "mynet-n750:blue:power";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
|
||||
gpio_ext_lna0 {
|
||||
gpio-hog;
|
||||
gpios = <15 0>;
|
||||
output-high;
|
||||
line-name = "mynet-n750:ext:lna0";
|
||||
};
|
||||
|
||||
gpio_ext_lna1 {
|
||||
gpio-hog;
|
||||
gpios = <18 0>;
|
||||
output-high;
|
||||
line-name = "mynet-n750:ext:lna1";
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader";
|
||||
reg = <0x000000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "bdcfg";
|
||||
reg = <0x040000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "devdata";
|
||||
reg = <0x050000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "devconf";
|
||||
reg = <0x060000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "seama";
|
||||
label = "firmware";
|
||||
reg = <0x070000 0xf80000>;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
port@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
|
||||
hub_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
hub_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "pci168c,0033";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
qca,no-eeprom;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
phy-mask = <0>;
|
||||
|
||||
switch0@1f {
|
||||
compatible = "qca,ar8327";
|
||||
reg = <0x1f>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
|
||||
0x10 0x80000080 /* POWER_ON_STRIP */
|
||||
0x50 0xc737c737 /* LED_CTRL0 */
|
||||
0x54 0x00000000 /* LED_CTRL1 */
|
||||
0x58 0x00000000 /* LED_CTRL2 */
|
||||
0x5c 0x0030c300 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
/* default for ar934x, except for 1000M */
|
||||
pll-data = <0x06000000 0x00000101 0x00001616>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
|
@ -655,6 +655,17 @@ define Device/rosinson_wr818
|
|||
endef
|
||||
TARGET_DEVICES += rosinson_wr818
|
||||
|
||||
define Device/wd_mynet-n750
|
||||
$(Device/seama)
|
||||
ATH_SOC := ar9344
|
||||
DEVICE_TITLE := Western Digital My Net N750
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
||||
SEAMA_SIGNATURE := wrgnd13_wd_av
|
||||
SUPPORTED_DEVICES += mynet-n750
|
||||
endef
|
||||
TARGET_DEVICES += wd_mynet-n750
|
||||
|
||||
define Device/wd_mynet-wifi-rangeextender
|
||||
ATH_SOC := ar9344
|
||||
DEVICE_TITLE := Western Digital My Net Wi-Fi Range Extender
|
||||
|
|
|
|||
Loading…
Reference in New Issue