mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-28 17:42:28 +00:00
mediatek: add support for Cudy TR3000 v1
Hardware: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 128 MiB SPI NAND - RAM: 512 MiB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax) - Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN - USB 3.0 port - Buttons: 1 Reset button, 1 slider button - LEDs: 1x Red, 1x White - Serial console: internal test points, 115200 8n1 - Power: 5 VDC, 3 A MAC addresses: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 80:af:ca:xx:xx:x1 | label+1 | | LAN | 80:af:ca:xx:xx:x0 | label | | WLAN 2g | 80:af:ca:xx:xx:x0 | label | | WLAN 5g | 82:af:ca:xx:xx:x0 | | +---------+-------------------+-----------+ Installation: The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below. To install using TFTP: 1. Connect to UART. 2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds. 3. A u-boot shell will automatically open. 4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file. 5. Run these steps in u-boot using the name of your file. setenv bootfile initramfs-kernel.bin tftpboot bootm 6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off. Signed-off-by: Luis Mita <luis@luismita.com>
This commit is contained in:
Luis Mita
Hauke Mehrtens
parent
30e8fd73ec
commit
63b8d98dd0
@ -5,6 +5,7 @@ set_preinit_iface() {
|
||||
ip link set lan up
|
||||
ifname=lan
|
||||
;;
|
||||
cudy,tr3000-v1|\
|
||||
glinet,gl-mt3000)
|
||||
ip link set eth1 up
|
||||
ifname=eth1
|
||||
|
||||
232
target/linux/mediatek/dts/mt7981b-cudy-tr3000-v1.dts
Normal file
232
target/linux/mediatek/dts/mt7981b-cudy-tr3000-v1.dts
Normal file
@ -0,0 +1,232 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Cudy TR3000 v1";
|
||||
compatible = "cudy,tr3000-v1", "mediatek,mt7981-spim-snand-rfb";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &gmac1;
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
mode {
|
||||
label = "mode";
|
||||
linux,input-type = <EV_SW>;
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status: led_0 {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_1 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
usb_vbus: regulator-usb {
|
||||
compatible = "regulator-fixed";
|
||||
|
||||
regulator-name = "usb-vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
|
||||
gpio = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_bdinfo_de00 1>;
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_bdinfo_de00 0>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
phy1: phy@1 {
|
||||
reg = <1>;
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
phy-mode = "2500base-x";
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
|
||||
reset-assert-us = <100000>;
|
||||
reset-deassert-us = <100000>;
|
||||
realtek,aldps-enable;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <52000000>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x0200000>;
|
||||
read-only;
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "bdinfo";
|
||||
reg = <0x380000 0x0040000>;
|
||||
read-only;
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_bdinfo_de00: macaddr@de00 {
|
||||
compatible = "mac-base";
|
||||
reg = <0xde00 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
partition@3C0000 {
|
||||
label = "FIP";
|
||||
reg = <0x3C0000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x5C0000 0x4000000>;
|
||||
compatible = "linux,ubi";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
vbus-supply = <&usb_vbus>;
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
@ -56,6 +56,7 @@ mediatek_setup_interfaces()
|
||||
dlink,aquila-pro-ai-m30-a1)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
|
||||
;;
|
||||
cudy,tr3000-v1|\
|
||||
glinet,gl-mt2500|\
|
||||
glinet,gl-mt3000|\
|
||||
glinet,gl-x3000|\
|
||||
|
||||
@ -69,6 +69,7 @@ case "$board" in
|
||||
addr=$(mtd_get_mac_binary "Factory" 0x8000)
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
cudy,tr3000-v1|\
|
||||
cudy,re3000-v1)
|
||||
addr=$(mtd_get_mac_binary bdinfo 0xde00)
|
||||
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
|
||||
|
||||
@ -485,6 +485,23 @@ define Device/cudy_re3000-v1
|
||||
endef
|
||||
TARGET_DEVICES += cudy_re3000-v1
|
||||
|
||||
define Device/cudy_tr3000-v1
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := TR3000
|
||||
DEVICE_VARIANT := v1
|
||||
DEVICE_DTS := mt7981b-cudy-tr3000-v1
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
SUPPORTED_DEVICES += R47
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := kmod-usb3 kmod-mt7981-firmware mt7981-wo-firmware
|
||||
endef
|
||||
TARGET_DEVICES += cudy_tr3000-v1
|
||||
|
||||
define Device/cudy_wr3000-v1
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := WR3000
|
||||
|
||||
Loading…
Reference in New Issue
Block a user