RepoMirrors/openwrt
1
0
Fork 0
mirror of git://git.openwrt.org/openwrt/openwrt.git synced 2024-12-30 02:22:09 +00:00
Code Issues Packages Projects Releases Wiki Activity

qualcommax: ipq807x: add support for Netgear WAX630

Browse Source 
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
  GND RXD TXD, beginning from the external antennas. 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet

Wlan:
* 4x4 in 2.4GHz  : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)

Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A

Mounting: Wall and ceiling
```

```
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to the console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
This commit is contained in:
Kristian Skramstad 2023-10-01 16:28:24 +02:00 committed by Hauke Mehrtens
parent f9e6218b82
commit 5e33fdfc47
7 changed files with 290 additions and 2 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

3
package/boot/uboot-envtools/files/qualcommax_ipq807x
View File

@ -11,7 +11,8 @@ case "$board" in
dynalink,dl-wrx36|\
netgear,rax120v2|\
netgear,wax218|\
netgear,wax620)
netgear,wax620|\
netgear,wax630)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"

253
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts Normal file
View File

@ -0,0 +1,253 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "ipq8074.dtsi"
#include "ipq8074-hk-cpu.dtsi"
#include "ipq8074-ess.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
/ {
model = "Netgear WAX630";
compatible = "netgear,wax630", "qcom,ipq8074";
aliases {
serial0 = &blsp1_uart5;
ethernet0 = &dp6_syn;
ethernet1 = &dp4;
label-mac-device = &dp6_syn;
led-boot = &led_system_blue;
led-failsafe = &led_system_red;
led-running = &led_system_green;
led-upgrade = &led_system_blue;
};
chosen {
stdout-path = "serial0:115200n8";
bootargs-append = " root=/dev/ubiblock0_1";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
led-spi {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
led_gpio: led-gpio@0 {
compatible = "fairchild,74hc595";
reg = <0>;
gpio-controller;
#gpio-cells = <2>;
registers-number = <1>;
enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
spi-max-frequency = <1000000>;
};
};
leds {
compatible = "gpio-leds";
led_system_red: system-red {
label = "system:red";
gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_system_green: system-green {
label = "system:green";
gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_system_blue: system-blue {
label = "system:blue";
gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
default-state = "off";
};
lan1-green {
label = "lan1:green";
gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
default-state = "off";
};
lan1-orange {
label = "lan1:orange";
gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
default-state = "off";
};
lan2-green {
label = "lan2:green";
gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
default-state = "off";
};
lan2-orange {
label = "lan2:orange";
gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
default-state = "off";
};
2g-blue {
label = "wlan2g:blue";
gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
default-state = "off";
};
2g-green {
label = "wlan2g:green";
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
default-state = "off";
};
5g-low-blue {
label = "wlan5g_low:blue";
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
default-state = "off";
};
5g-low-green {
label = "wlan5g_low:green";
gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
default-state = "off";
};
5g-high-blue {
label = "wlan5g_high:blue";
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
default-state = "off";
};
5g-high-green {
label = "wlan5g_high:green";
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
};
&edma {
status = "okay";
};
&switch {
status = "okay";
switch_cpu_bmp = <0x01>;
switch_lan_bmp = <0x3e>;
switch_wan_bmp = <0x40>;
switch_mac_mode = <0x00>;
switch_mac_mode1 = <0xff>;
switch_mac_mode2 = <0x0d>;
bm_tick_mode = <0x00>;
tm_tick_mode = <0x00>;
qcom,port_phyinfo {
port@3 {
port_id = <4>;
phy_address = <3>;
};
port@5 {
port_id = <6>;
phy_address = <28>;
port_mac_sel = "QGMAC_PORT";
};
};
};
&tlmm {
mdio_pins: mdio-pins {
mdc {
pins = "gpio68";
function = "mdc";
drive-strength = <8>;
bias-pull-up;
};
mdio {
pins = "gpio69";
function = "mdio";
drive-strength = <8>;
bias-pull-up;
};
};
};
&mdio {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
qca8075: ethernet-phy@3 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <3>;
};
qca8081: ethernet-phy@28 {
compatible = "ethernet-phy-id004d.d101";
reg = <28>;
reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>;
};
};
&dp4 {
status = "okay";
phy-handle = <&qca8075>;
label = "lan2";
};
&dp6_syn {
status = "okay";
phy-handle = <&qca8081>;
label = "lan1";
};
&qpic_bam {
status = "okay";
};
&qpic_nand {
status = "okay";
nand@0 {
reg = <0>;
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
nand-bus-width = <8>;
partitions {
compatible = "qcom,smem-part";
};
};
};
&blsp1_uart5 {
status = "okay";
};
&wifi {
status = "okay";
qcom,ath11k-calibration-variant = "Netgear-WAX630";
};

25
target/linux/qualcommax/image/ipq807x.mk
View File

@ -23,6 +23,16 @@ define Device/UbiFit
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Build/wax6xx-netgear-tar
mkdir $@.tmp
mv $@ $@.tmp/nand-ipq807x-apps.img
md5sum $@.tmp/nand-ipq807x-apps.img | cut -c 1-32 > $@.tmp/nand-ipq807x-apps.md5sum
echo $(DEVICE_MODEL) > $@.tmp/metadata.txt
echo $(DEVICE_MODEL)"_V9.9.9.9" > $@.tmp/version
tar -C $@.tmp/ -cf $@ .
rm -rf $@.tmp
endef
define Device/buffalo_wxr-5950ax12
$(call Device/FitImage)
DEVICE_VENDOR := Buffalo
@ -146,6 +156,21 @@ define Device/netgear_wax620
endef
TARGET_DEVICES += netgear_wax620
define Device/netgear_wax630
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX630
DEVICE_DTS_CONFIG := config@hk01
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8074
IMAGES := ui-factory.tar factory.ubi sysupgrade.bin
IMAGE/ui-factory.tar := append-ubi | wax6xx-netgear-tar
DEVICE_PACKAGES += kmod-spi-gpio ipq-wifi-netgear_wax630
endef
TARGET_DEVICES += netgear_wax630
define Device/prpl_haze
$(call Device/FitImage)
$(call Device/EmmcImage)

4
target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds
View File

@ -20,6 +20,10 @@ netgear,wax218)
netgear,wax620)
ucidef_set_led_netdev "lan" "LAN" "lan:green" "lan"
;;
netgear,wax630)
ucidef_set_led_netdev "lan1" "LAN1" "lan1:green" "lan1"
ucidef_set_led_netdev "lan2" "LAN2" "lan2:green" "lan2"
;;
redmi,ax6|\
xiaomi,ax3600)
ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan"

3
target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
View File

@ -29,6 +29,9 @@ ipq807x_setup_interfaces()
netgear,wax620)
ucidef_set_interface_lan "lan" "dhcp"
;;
netgear,wax630)
ucidef_set_interface_lan "lan1 lan2" "dhcp"
;;
prpl,haze)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
;;

1
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
View File

@ -17,6 +17,7 @@ case "$FIRMWARE" in
netgear,rax120v2|\
netgear,wax218|\
netgear,wax620|\
netgear,wax630|\
qnap,301w|\
redmi,ax6|\
xiaomi,ax3600|\

3
target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
View File

@ -70,7 +70,8 @@ platform_do_upgrade() {
edimax,cax1800|\
netgear,rax120v2|\
netgear,wax218|\
netgear,wax620)
netgear,wax620|\
netgear,wax630)
nand_do_upgrade "$1"
;;
prpl,haze|\