mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2024-12-26 16:42:47 +00:00
ipq806x: add support for Linksys e8350-v1
AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064. https://www.linksys.com/support-product?sku=E8350 Specification: - Qualcomm dual-core IPQ8064 @ 1.4 GHz - 512 MB of RAM - 4 MB of SPI NOR MX25U3235F - 128 MB of NAND S34MS01G2 - Qualcomm QCA9880 2.4GHz 802.11bgn - Quantenna QSR1000 5GHz 802.11ac (no support) - 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet - Qualcomm Atheros QCA8337 switch - 1 x 3.0 + 1 x 2.0 (combo with eSata port) - 115200, 8N1 internal serial console - Power, Reset, WPS and WLAN buttons - Power, WPS and WLAN leds - 12 VDC, 3 A power Installation: The installation must be done using web interface of the router. To achive this new firmware-utils tool was added to set correct magic headers for the factory images. Installation from vendor firmware: 1. Flash over the native Linksys WEB interface using factory image. Installation using recovery mode: 1. Power off the device and disconnect the WAN port. (Only LAN port to be connected) 2. Press & hold the "Reset" button 3. Power on the device & wait 10 seconds with pressed "Reset" button 4. Set IP Internet Protocol on your PC from 192.168.1.0/24 network (Router is on IP 192.168.1.1) 5. Open the Firmware Recovery page in your browser: http://192.168.1.1/index.shtml Firmware Recovery -> File Name -> Recovery & Reboot The device page in inbox: https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1 Signed-off-by: Sergey Filippov <sergey.filippov@outlook.com> Link: https://github.com/openwrt/openwrt/pull/15798 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit is contained in:
Sergey Filippov
Christian Marangi
parent
d514213336
commit
45b3c620e5
@ -46,6 +46,9 @@ fortinet,fap-421e)
|
||||
ucidef_set_led_wlan "wlan5g" "5G" "yellow:5g" "phy0tpt"
|
||||
ucidef_set_led_usbport "usb" "USB" "amber:power" "usb1-port1" "usb2-port1"
|
||||
;;
|
||||
linksys,e8350-v1)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "green:wifi" "phy0tpt"
|
||||
;;
|
||||
meraki,mr52)
|
||||
ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0"
|
||||
ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1"
|
||||
|
||||
@ -23,6 +23,7 @@ ipq806x_setup_interfaces()
|
||||
netgear,r7500 |\
|
||||
netgear,r7500v2 |\
|
||||
qcom,ipq8064-ap148 |\
|
||||
linksys,e8350-v1 |\
|
||||
linksys,ea7500-v1 |\
|
||||
linksys,ea8500 |\
|
||||
nec,wg2600hp3 |\
|
||||
@ -87,6 +88,7 @@ ipq806x_setup_macs()
|
||||
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
||||
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
||||
;;
|
||||
linksys,e8350-v1 |\
|
||||
zyxel,nbg6817)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii 0:appsblenv ethaddr)
|
||||
ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)"
|
||||
|
||||
@ -14,6 +14,7 @@ platform_do_upgrade() {
|
||||
askey,rt4230w-rev6 |\
|
||||
compex,wpq864|\
|
||||
fortinet,fap-421e|\
|
||||
linksys,e8350-v1|\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
netgear,r7500v2 |\
|
||||
|
||||
@ -0,0 +1,428 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
#include "qcom-ipq8064-v2.0-smb208.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Linksys E8350 V1 WiFi Router";
|
||||
compatible = "linksys,e8350-v1", "qcom,ipq8064";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi4_serial;
|
||||
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "wifi";
|
||||
gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
debounce-interval = <60>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_power: power {
|
||||
label = "green:power";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "green:wps";
|
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "green:wifi";
|
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
|
||||
nand-ecc-strength = <4>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0 0x4000000>;
|
||||
};
|
||||
partition@4000000 {
|
||||
label = "extra";
|
||||
reg = <0x4000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qcom_pinmux {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio68","gpio65", "gpio67";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio26","gpio53", "gpio54";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
switch_reset: switch_reset_pins {
|
||||
mux {
|
||||
pins = "gpio63";
|
||||
function = "gpio";
|
||||
drive-strength = <12>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "okay";
|
||||
|
||||
spi5: spi@1a280000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
m25p80@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <51200000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:sbl1";
|
||||
reg = <0x0000000 0x0010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@10000 {
|
||||
label = "0:mibib";
|
||||
reg = <0x0010000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "0:sbl2";
|
||||
reg = <0x0030000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:sbl3";
|
||||
reg = <0x0050000 0x0030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:ddrconfig";
|
||||
reg = <0x0080000 0x0010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@90000 {
|
||||
label = "0:ssd";
|
||||
reg = <0x0090000 0x0010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "0:tz";
|
||||
reg = <0x00a0000 0x0030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "0:rpm";
|
||||
reg = <0x00d0000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "0:oldappsbl";
|
||||
reg = <0x00f0000 0x0040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@130000 {
|
||||
label = "0:appsblenv";
|
||||
reg = <0x0130000 0x0040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x0170000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@190000 {
|
||||
label = "0:uboot";
|
||||
reg = <0x0190000 0x0050000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1e0000 {
|
||||
label = "0:oldnss1";
|
||||
reg = <0x01e0000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "0:nvram";
|
||||
reg = <0x0200000 0x0020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "0:oldkernel";
|
||||
reg = <0x0220000 0x01e0000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hs_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
max-link-speed = <1>;
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
/* Switch from documentation require at least 12ms for reset */
|
||||
reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>;
|
||||
reset-post-delay-us = <12000>;
|
||||
|
||||
switch@10 {
|
||||
compatible = "qca,qca8337";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x10>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac1>;
|
||||
phy-mode = "rgmii";
|
||||
tx-internal-delay-ps = <1000>;
|
||||
rx-internal-delay-ps = <1000>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan1";
|
||||
phy-mode = "internal";
|
||||
phy-handle = <&phy_port1>;
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan2";
|
||||
phy-mode = "internal";
|
||||
phy-handle = <&phy_port2>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
phy-mode = "internal";
|
||||
phy-handle = <&phy_port3>;
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan4";
|
||||
phy-mode = "internal";
|
||||
phy-handle = <&phy_port4>;
|
||||
};
|
||||
|
||||
port@5 {
|
||||
reg = <5>;
|
||||
label = "wan";
|
||||
phy-mode = "internal";
|
||||
phy-handle = <&phy_port5>;
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac2>;
|
||||
phy-mode = "sgmii";
|
||||
qca,sgmii-enable-pll;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
phy_port1: phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
phy_port2: phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
phy_port3: phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
phy_port4: phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
phy_port5: phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&tcsr {
|
||||
qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
|
||||
compatible = "qcom,tcsr", "syscon";
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "okay";
|
||||
};
|
||||
@ -35,6 +35,18 @@ define Build/edimax-header
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
# tune addpattern for Linksys E8350-V1 fw pattern generation
|
||||
define Build/linksys-bin
|
||||
$(STAGING_DIR_HOST)/bin/addpattern -p $(FW_DEVICE_ID) -v $(FW_VERSION) $(if $(SERIAL),-s $(SERIAL)) -i $@ -o $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
# Use Linksys fw header generator to upgrade openwrt factory image over the native Linksys WEB interface
|
||||
define Build/linksys-addfwhdr
|
||||
-$(STAGING_DIR_HOST)/bin/linksys-addfwhdr -i $@ -o $@.new \
|
||||
;mv "$@.new" "$@"
|
||||
endef
|
||||
|
||||
define Device/DniImage
|
||||
KERNEL_SUFFIX := -uImage
|
||||
KERNEL = kernel-bin | append-dtb | uImage none
|
||||
@ -189,6 +201,23 @@ define Device/fortinet_fap-421e
|
||||
endef
|
||||
TARGET_DEVICES += fortinet_fap-421e
|
||||
|
||||
define Device/linksys_e8350-v1
|
||||
$(call Device/LegacyImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := E8350
|
||||
DEVICE_VARIANT := v1
|
||||
SOC := qcom-ipq8064
|
||||
FW_VERSION := v1.0.03.003
|
||||
FW_DEVICE_ID := 8350
|
||||
PAGESIZE := 2048
|
||||
BLOCKSIZE := 128k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES = factory.bin sysupgrade.bin
|
||||
IMAGE/factory.bin := append-ubi | check-size 0x04000000 | linksys-addfwhdr | linksys-bin
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
|
||||
endef
|
||||
TARGET_DEVICES += linksys_e8350-v1
|
||||
|
||||
define Device/linksys_ea7500-v1
|
||||
$(call Device/LegacyImage)
|
||||
$(Device/kernel-size-migration)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user