ipq807x: add Dynalink DL-WRX36

Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>

package/boot/uboot-envtools/files/ipq807x

@@ -8,6 +8,11 @@ touch /etc/config/ubootenv
 board=$(board_name)
 
 case "$board" in
+dynalink,dl-wrx36)
+	idx="$(find_mtd_index 0:appsblenv)"
+	[ -n "$idx" ] && \
+		ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
+	;;
 edgecore,eap102)
 	idx="$(find_mtd_index 0:appsblenv)"
 	[ -n "$idx" ] && \

package/firmware/ipq-wifi/Makefile

@@ -27,6 +27,7 @@ endef
 ALLWIFIBOARDS:= \
 	aruba_ap-365 \
 	devolo_magic-2-wifi-next \
+	dynalink_dl-wrx36 \
 	edgecore_eap102 \
 	edgecore_ecw5410 \
 	edgecore_oap100 \
@@ -124,6 +125,7 @@ endef
 
 $(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
 $(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
+$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
 $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
 $(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
 $(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))

target/linux/ipq807x/base-files/etc/board.d/02_network

@@ -11,6 +11,9 @@ ipq807x_setup_interfaces()
 	local board="$1"
 
 	case "$board" in
+	dynalink,dl-wrx36)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
+		;;
 	edgecore,eap102)
 		ucidef_set_interfaces_lan_wan "lan" "wan"
 		;;

target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata

@@ -11,6 +11,7 @@ case "$FIRMWARE" in
 	case "$board" in
 	edgecore,eap102|\
 	edimax,cax1800|\
+	dynalink,dl-wrx36|\
 	qnap,301w|\
 	redmi,ax6|\
 	xiaomi,ax3600|\

target/linux/ipq807x/base-files/lib/upgrade/platform.sh

@@ -43,6 +43,9 @@ platform_pre_upgrade() {
 
 platform_do_upgrade() {
 	case "$(board_name)" in
+	dynalink,dl-wrx36)
+		nand_do_upgrade "$1"
+		;;
 	edgecore,eap102)
 		active="$(fw_printenv -n active)"
 		if [ "$active" -eq "1" ]; then

target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts

@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2022, Robert Marko <robimarko@gmail.com> */
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Dynalink DL-WRX36";
+	compatible = "dynalink,dl-wrx36", "qcom,ipq8074";
+
+	aliases {
+		led-boot = &led_system_red;
+		led-failsafe = &led_system_red;
+		led-running = &led_system_blue;
+		led-upgrade = &led_system_red;
+		serial0 = &blsp1_uart5;
+		/* Aliases as required by u-boot to patch MAC addresses */
+		ethernet0 = &dp6_syn;
+		ethernet1 = &dp4;
+		ethernet2 = &dp3;
+		ethernet3 = &dp2;
+		ethernet4 = &dp1;
+		label-mac-device = &dp6_syn;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " root=/dev/ubiblock0_1";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system_blue: system-blue {
+			label = "blue:system";
+			gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led_system_red: system-red {
+			label = "red:system";
+			gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&tlmm {
+	mdio_pins: mdio-pins {
+		mdc {
+			pins = "gpio68";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mdio {
+			pins = "gpio69";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+};
+
+&blsp1_uart5 {
+	status = "okay";
+};
+
+&prng {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+
+		partitions {
+			compatible = "qcom,smem-part";
+		};
+	};
+};
+
+&qusb_phy_0 {
+	status = "okay";
+};
+
+&ssphy_0 {
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+	qca8075_0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	qca8075_1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+
+	qca8075_2: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <2>;
+	};
+
+	qca8075_3: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <3>;
+	};
+
+	qca8081: ethernet-phy@28 {
+		compatible = "ethernet-phy-id004d.d101";
+		reg = <28>;
+		reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&switch {
+	status = "okay";
+
+	switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+	switch_lan_bmp = <0x3e>; /* lan port bitmap */
+	switch_wan_bmp = <0x40>; /* wan port bitmap */
+	switch_mac_mode = <0xb>; /* mac mode for uniphy instance0*/
+	switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+	switch_mac_mode2 = <0xc>; /* mac mode for uniphy instance2*/
+	bm_tick_mode = <0>; /* bm tick mode */
+	tm_tick_mode = <0>; /* tm tick mode */
+
+	qcom,port_phyinfo {
+		port@0 {
+			port_id = <1>;
+			phy_address = <0>;
+		};
+		port@1 {
+			port_id = <2>;
+			phy_address = <1>;
+		};
+		port@2 {
+			port_id = <3>;
+			phy_address = <2>;
+		};
+		port@3 {
+			port_id = <4>;
+			phy_address = <3>;
+		};
+		port@5 {
+			port_id = <6>;
+			phy_address = <28>;
+			port_mac_sel = "QGMAC_PORT";
+		};
+	};
+};
+
+&edma {
+	status = "okay";
+};
+
+&dp1 {
+	status = "okay";
+	phy-handle = <&qca8075_0>;
+	label = "lan4";
+};
+
+&dp2 {
+	status = "okay";
+	phy-handle = <&qca8075_1>;
+	label = "lan3";
+};
+
+&dp3 {
+	status = "okay";
+	phy-handle = <&qca8075_2>;
+	label = "lan2";
+};
+
+&dp4 {
+	status = "okay";
+	phy-handle = <&qca8075_3>;
+	label = "lan1";
+};
+
+&dp6_syn {
+	status = "okay";
+	phy-handle = <&qca8081>;
+	label = "wan";
+};
+
+&wifi {
+	status = "okay";
+	qcom,ath11k-calibration-variant = "Dynalink-DL-WRX36";
+};

target/linux/ipq807x/image/generic.mk

@@ -17,6 +17,19 @@ define Device/UbiFit
 	IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
 endef
 
+define Device/dynalink_dl-wrx36
+	$(call Device/FitImage)
+	$(call Device/UbiFit)
+	DEVICE_VENDOR := Dynalink
+	DEVICE_MODEL := DL-WRX36
+	BLOCKSIZE := 128k
+	PAGESIZE := 2048
+	DEVICE_DTS_CONFIG := config@rt5010w-d350-rev0
+	SOC := ipq8072
+	DEVICE_PACKAGES := ipq-wifi-dynalink_dl-wrx36
+endef
+TARGET_DEVICES += dynalink_dl-wrx36
+
 define Device/edgecore_eap102
 	$(call Device/FitImage)
 	$(call Device/UbiFit)