ipq40xx: add support for EZVIZ CS-W3-WD1200G EUP

Hardware: SOC: Qualcomm IPQ4018 RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MB Macronix MX25L12805D ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN) WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz) BUTTON: Shared WPS/Reset button LED: RGB Status/Power LED SERIAL: Header J8 (UART, Left side of board). Numbered from top to bottom: (1) GND, (2) TX, (3) RX, (4) VCC (White triangle next to it). 3.3v, 115200, 8N1 Tested/Working: * Ethernet * WiFi (2.4 and 5GHz) * Status LED * Reset Button (See note below) Implementation notes: * The shared WPS/Reset button is implemented as a Reset button * I could not find a original firmware image to reverse engineer, meaning currently it's not possible to flash OpenWrt through the Web GUI. Installation (Through Serial console & TFTP): 1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to one of the LAN ports 2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on your pc, to serve the image 2. Connect to the router through serial (See connection properties above) 3. Hit a key during startup, to pause startup 4. type `setenv serverip 192.168.1.12`, to set the tftp server address 5. type `tftpboot`, to load the image from the laptop through tftp 6. type `bootm` to run the loaded image from memory 6. (If you want to return to stock firmware later, create an full MTD backup, e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup) 7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.: `scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin` 8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin` Revert to stock: To revert to stock, you need the MTD backup from step 6 above: 1. Unpack the MTD backup archive 2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup) 3. On the router, do `mtd write mtd8_firmware.backup firmware` Signed-off-by: Tom Brouwer <tombrouwer@outlook.com> [removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-12 13:13:30 +01:00 · 2020-01-12 13:13:30 +01:00 · 2090b8af0a
parent a0c0ad728c
commit 2090b8af0a
9 changed files with 277 additions and 1 deletions
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@ -26,6 +26,7 @@ endef
 ALLWIFIBOARDS:= \
 	aruba_ap-303 \
 	avm_fritzrepeater-1200 \
+	ezviz_cs-w3-wd1200g-eup \
 	linksys_ea8300 \
 	qxwlan_e2600ac

@ -92,6 +93,7 @@ endef

 $(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
 $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
+$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
 $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
 $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))

--- a/package/firmware/ipq-wifi/board-ezviz_cs-w3-wd1200g-eup.qca4019
+++ b/package/firmware/ipq-wifi/board-ezviz_cs-w3-wd1200g-eup.qca4019
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@ -54,6 +54,11 @@ ipq40xx_setup_interfaces()
 	compex,wpj428)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
+		;;
 	glinet,gl-b1300)
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \
@ -97,6 +102,9 @@ ipq40xx_setup_macs()
 		wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		label_mac=$(mtd_get_mac_binary "ART" 0x6)
+		;;
 	linksys,ea6350v3)
 		wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@ -46,6 +46,7 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
+	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
@ -115,6 +116,7 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
+	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@ -9,6 +9,10 @@ preinit_set_mac_address() {
 		ip link set dev eth0 address $(macaddr_add "$base_mac" +1)
 		ip link set dev eth1 address $(macaddr_add "$base_mac" +3)
 		;;
+	ezviz,cs-w3-wd1200g-eup)
+		ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
+		ip link set dev eth1 address $(mtd_get_mac_binary "ART" 0x0)
+		;;
 	linksys,ea8300)
 		base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		ip link set dev eth0 address "${base_mac}"
--- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
@ -7,6 +7,7 @@ set_preinit_iface() {
 	aruba,ap-303| \
 	asus,rt-ac58u| \
 	avm,fritzbox-4040| \
+	ezviz,cs-w3-wd1200g-eup| \
 	glinet,gl-b1300| \
 	linksys,ea8300| \
 	meraki,mr33| \
--- a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts
@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "EZVIZ CS-W3-WD1200G EUP";
+	compatible = "ezviz,cs-w3-wd1200g-eup";
+
+	aliases {
+		led-boot = &led_status_green;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_green;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+			reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+			reset-delay-us = <5000>;
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: status_red {
+			label = "cs-w3-wd1200g-eup:red:status";
+			gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_green: status_green {
+			label = "cs-w3-wd1200g-eup:green:status";
+			gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_blue: status_blue {
+			label = "cs-w3-wd1200g-eup:blue:status";
+			gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition1@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition2@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition3@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition4@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition5@E0000 {
+				label = "APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+
+			partition6@F0000 {
+				label = "APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition7@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+
+			partition9@580000 {
+				compatible = "denx,fit";
+				label = "firmware";
+				reg = <0x00180000 0x00e80000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+};
+
+&wifi1 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+};
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@ -257,6 +257,22 @@ define Device/engenius_ens620ext
 endef
 TARGET_DEVICES += engenius_ens620ext

+define Device/ezviz_cs-w3-wd1200g-eup
+	$(call Device/FitImage)
+	DEVICE_VENDOR := EZVIZ
+	DEVICE_MODEL := CS-W3-WD1200G
+	DEVICE_VARIANT := EUP
+	DEVICE_DTS_CONFIG := config@4
+	IMAGE_SIZE := 14848k
+	SOC := qcom-ipq4018
+	IMAGES := sysupgrade.bin
+	IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
+		append-metadata
+	DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
+		ipq-wifi-ezviz_cs-w3-wd1200g-eup
+endef
+TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
+
 define Device/glinet_gl-b1300
 	$(call Device/FitImage)
 	DEVICE_VENDOR := GL.iNet
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@ -10,12 +10,13 @@ Signed-off-by: John Crispin <john@phrozen.org>

 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,38 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,39 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8074-dragonboard.dtb \
 	qcom-apq8084-ifc6540.dtb \
 	qcom-apq8084-mtp.dtb \
 +	qcom-ipq4018-a42.dtb \
 +	qcom-ipq4018-ap120c-ac.dtb \
+	qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
 +	qcom-ipq4018-ea6350v3.dtb \
 +	qcom-ipq4018-eap1300.dtb \
 +	qcom-ipq4018-ens620ext.dtb \