openwrt/target/linux/bmips/dts/bcm6328-inteno-xg6846.dts

// SPDX-License-Identifier: GPL-2.0

/*
 * Devicetree for the Inteno XG6846 router, mostly used as a
 * media converter from fiber to twisted pair ethernet
 * "fiber modem" in many households in Sweden. The Marvell
 * switch has one of its ports connected to an SFP (Small Form
 * Factor pluggable) optical fiber receiver, which is bridged
 * to the twisted pair connector LAN1.
 *
 * This device tree is inspired by research from the OpenWrt
 * and Sweclockers forums, including contributions from
 * NPeca75, mrhaav and csom.
 *
 * Some devices have a USB type A host receptacle mounted,
 * some do not.
 */

#include "bcm6328.dtsi"

/ {
	model = "Inteno XG6846";
	compatible = "inteno,xg6846", "brcm,bcm6328";

	aliases {
		led-boot = &led_power_red;
		led-failsafe = &led_power_red;
		led-running = &led_power_green;
		led-upgrade = &led_power_red;
	};

	/*
	 * This I2C port is connected to the SFP and reflects the EEPROM etc
	 * inside the SFP module. If the module is not plugged in, consequently
	 * nothing will be found on the bus.
	 */
	i2c0: i2c-sfp {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		#address-cells = <1>;
		#size-cells = <0>;

		sfp_eeprom: eeprom@50 {
			compatible = "atmel,24c02";
			reg = <0x50>;
			read-only;
		};
	};

	/* This I2C bus is used for the external CATV connector (usually unused) */
	i2c1: i2c-catv {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		#address-cells = <1>;
		#size-cells = <0>;
	};

	keys {
		compatible = "gpio-keys-polled";
		poll-interval = <100>;

		reset {
			label = "reset";
			gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
			debounce-interval = <60>;
		};
	};

	sfp0: sfp0 {
		compatible = "sff,sfp";
		i2c-bus = <&i2c0>;
		los-gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
	};
};

&hsspi {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		/*
		 * HW 1.0-1.1: Spansion S25FL128S1
		 * HW 1.3: Winbond W25Q128
		 *
		 * Fast Read Data max speed is 50MHz, see the Winbond W25Q128
		 * datasheet table 9.5 "AC Electrical Characteristics", we can
		 * use this speed because the chip supports fast reads. Older
		 * HW has different NOR chips, I assume they can all do fast
		 * reads.
		 */
		spi-max-frequency = <104000000>;
		spi-tx-bus-width = <2>;
		spi-rx-bus-width = <2>;
		m25p,fast-read;
		reg = <0>;

		#address-cells = <1>;
		#size-cells = <1>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "cfe";
				reg = <0x0000000 0x0010000>;
				read-only;

				nvmem-layout {
					compatible = "fixed-layout";
					#address-cells = <1>;
					#size-cells = <1>;

					macaddr_cfe_6a0: macaddr@6a0 {
						reg = <0x6a0 0x6>;
					};
				};
			};

			partition@10000 {
				compatible = "openwrt,uimage", "denx,uimage";
				reg = <0x010000 0xfe0000>;
				label = "firmware";
				openwrt,offset = <0x30000>;
			};

			partition@ff0000 {
				reg = <0xff0000 0x010000>;
				label = "nvram";
			};
		};
	};
};

&ehci {
	status = "okay";
};

&ethernet {
	status = "okay";

	nvmem-cells = <&macaddr_cfe_6a0>;
	nvmem-cell-names = "mac-address";
};

&leds {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_leds>,
		    <&pinctrl_ephy1_spd_led>,
		    <&pinctrl_ephy3_spd_led>;

	led@16 {
		reg = <16>;
		active-low;
		function = LED_FUNCTION_USB;
		color = <LED_COLOR_ID_GREEN>;
	};

	led_power_red: led@18 {
		reg = <18>;
		active-low;
		function = LED_FUNCTION_POWER;
		color = <LED_COLOR_ID_RED>;
		panic-indicator;
	};

	led_power_green: led@20 {
		reg = <20>;
		active-low;
		function = LED_FUNCTION_POWER;
		color = <LED_COLOR_ID_GREEN>;
	};
};

&mdio_ext {
	switch1: switch@0 {
		/* The switch is not using any external IRQ, sadly */
		compatible = "marvell,mv88e6085";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;

		interrupt-controller;
		#interrupt-cells = <2>;

		dsa,member = <1 0>;

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				label = "lan1";

				phy-handle = <&lan1phy>;

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_LAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_LAN;
					};
				};
			};

			port@1 {
				reg = <1>;
				label = "lan2";

				phy-handle = <&lan2phy>;

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_LAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_LAN;
					};
				};
			};

			port@2 {
				reg = <2>;
				label = "lan3";

				phy-handle = <&lan3phy>;

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_LAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_LAN;
					};
				};
			};

			port@3 {
				reg = <3>;
				label = "lan4";

				phy-handle = <&lan4phy>;

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_LAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_LAN;
					};
				};
			};

			port@4 {
				reg = <4>;
				label = "ext1";

				phy-handle = <&ext1phy>;

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_WAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_WAN;
					};
				};
			};

			port@5 {
				reg = <5>;
				label = "wan";

				phy-mode = "rgmii-id";
				sfp = <&sfp0>;

				fixed-link {
					speed = <1000>;
					full-duplex;
				};

				leds {
					#address-cells = <1>;
					#size-cells = <0>;

					led@0 {
						reg = <0>;
						color = <LED_COLOR_ID_GREEN>;
						function = LED_FUNCTION_WAN;
						default-state = "keep";
					};

					led@1 {
						reg = <1>;
						color = <LED_COLOR_ID_AMBER>;
						function = LED_FUNCTION_WAN;
					};
				};
			};

			port@6 {
				reg = <6>;

				phy-mode = "rgmii-id";
				ethernet = <&switch0port4>;

				fixed-link {
					speed = <1000>;
					full-duplex;
				};
			};
		};

		mdio {
			#address-cells = <1>;
			#size-cells = <0>;

			lan1phy: ethernet-phy@0 {
				reg = <0>;
				interrupt-parent = <&switch1>;
				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
			};

			lan2phy: ethernet-phy@1 {
				reg = <1>;
				interrupt-parent = <&switch1>;
				interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
			};

			lan3phy: ethernet-phy@2 {
				reg = <2>;
				interrupt-parent = <&switch1>;
				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
			};

			lan4phy: ethernet-phy@3 {
				reg = <3>;
				interrupt-parent = <&switch1>;
				interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
			};

			ext1phy: ethernet-phy@4 {
				reg = <4>;
				interrupt-parent = <&switch1>;
				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
			};
		};
	};
};

&ohci {
	status = "okay";
};

&pinctrl {
	pinctrl_leds: leds {
		function = "led";
		pins = "gpio16", "gpio18", "gpio20";
	};
};

&switch0 {
	dsa,member = <0 0>;

	ports {
		switch0port4: port@4 {
			reg = <4>;
			label = "extsw";

			phy-mode = "rgmii";

			fixed-link {
				speed = <1000>;
				full-duplex;
			};
		};
	};
};

&uart0 {
	status = "okay";
};

&usbh {
	status = "okay";
};