2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_AT803X_PHY=y
|
2018-05-06 08:20:11 +00:00
|
|
|
CONFIG_BLK_MQ_PCI=y
|
2018-12-27 01:32:38 +00:00
|
|
|
CONFIG_GPIO_WATCHDOG=y
|
|
|
|
|
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_INTEL_XWAY_PHY=y
|
2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_IP17XX_PHY=y
|
2018-05-06 08:20:11 +00:00
|
|
|
CONFIG_LEDS_RESET=y
|
2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_MARVELL_PHY=y
|
|
|
|
|
CONFIG_MICREL_PHY=y
|
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro
This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.
The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.
This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).
All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.
Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.
Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.
One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
|
|
|
CONFIG_MTD_REDBOOT_PARTS=y
|
ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-06 19:15:19 +00:00
|
|
|
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_MTD_SPLIT_EVA_FW=y
|
2018-05-06 08:20:11 +00:00
|
|
|
CONFIG_OF_ADDRESS_PCI=y
|
|
|
|
|
CONFIG_OF_PCI=y
|
|
|
|
|
CONFIG_OF_PCI_IRQ=y
|
|
|
|
|
CONFIG_PCI=y
|
|
|
|
|
CONFIG_PCI_AR71XX=y
|
|
|
|
|
CONFIG_PCI_AR724X=y
|
|
|
|
|
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
|
|
|
|
|
CONFIG_PCI_DOMAINS=y
|
|
|
|
|
CONFIG_PHY_AR7100_USB=y
|
|
|
|
|
CONFIG_PHY_AR7200_USB=y
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_REGULATOR=y
|
|
|
|
|
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_RTL8366RB_PHY=y
|
|
|
|
|
CONFIG_RTL8366S_PHY=y
|
|
|
|
|
CONFIG_RTL8366_SMI=y
|
|
|
|
|
CONFIG_RTL8367_PHY=y
|
2018-12-27 01:32:38 +00:00
|
|
|
CONFIG_WATCHDOG_CORE=y
|
