[kex.c kex.h kexecdh.c key.c key.h monitor.c ssh-ecdsa.c]
ECDH/ECDSA compliance fix: these methods vary the hash function they use
(SHA256/384/512) depending on the length of the curve in use. The previous
code incorrectly used SHA256 in all cases.
This fix will cause authentication failure when using 384 or 521-bit curve
keys if one peer hasn't been upgraded and the other has. (256-bit curve
keys work ok). In particular you may need to specify HostkeyAlgorithms
when connecting to a server that has not been upgraded from an upgraded
client.
ok naddy@
[PROTOCOL PROTOCOL.agent PROTOCOL.certkeys auth2-jpake.c authfd.c]
[authfile.c buffer.h dns.c kex.c kex.h key.c key.h monitor.c]
[monitor_wrap.c myproposal.h packet.c packet.h pathnames.h readconf.c]
[ssh-add.1 ssh-add.c ssh-agent.1 ssh-agent.c ssh-keygen.1 ssh-keygen.c]
[ssh-keyscan.1 ssh-keyscan.c ssh-keysign.8 ssh.1 ssh.c ssh2.h]
[ssh_config.5 sshconnect.c sshconnect2.c sshd.8 sshd.c sshd_config.5]
[uuencode.c uuencode.h bufec.c kexecdh.c kexecdhc.c kexecdhs.c ssh-ecdsa.c]
Implement Elliptic Curve Cryptography modes for key exchange (ECDH) and
host/user keys (ECDSA) as specified by RFC5656. ECDH and ECDSA offer
better performance than plain DH and DSA at the same equivalent symmetric
key length, as well as much shorter keys.
Only the mandatory sections of RFC5656 are implemented, specifically the
three REQUIRED curves nistp256, nistp384 and nistp521 and only ECDH and
ECDSA. Point compression (optional in RFC5656 is NOT implemented).
Certificate host and user keys using the new ECDSA key types are supported.
Note that this code has not been tested for interoperability and may be
subject to change.
feedback and ok markus@
[auth-rsa.c channels.c jpake.c key.c misc.c misc.h monitor.c]
[packet.c ssh-rsa.c]
implement a timing_safe_cmp() function to compare memory without leaking
timing information by short-circuiting like memcmp() and use it for
some of the more sensitive comparisons (though nothing high-value was
readily attackable anyway); "looks ok" markus@
[auth-rhosts.c monitor.c monitor_wrap.c session.c auth-options.c sshd.c]
Hold authentication debug messages until after successful authentication.
Fixes an info leak of environment variables specified in authorized_keys,
reported by Jacob Appelbaum. ok djm@
- djm@cvs.openbsd.org 2010/02/26 20:29:54
[PROTOCOL PROTOCOL.agent PROTOCOL.certkeys addrmatch.c auth-options.c]
[auth-options.h auth.h auth2-pubkey.c authfd.c dns.c dns.h hostfile.c]
[hostfile.h kex.h kexdhs.c kexgexs.c key.c key.h match.h monitor.c]
[myproposal.h servconf.c servconf.h ssh-add.c ssh-agent.c ssh-dss.c]
[ssh-keygen.1 ssh-keygen.c ssh-rsa.c ssh.1 ssh.c ssh2.h sshconnect.c]
[sshconnect2.c sshd.8 sshd.c sshd_config.5]
Add support for certificate key types for users and hosts.
OpenSSH certificate key types are not X.509 certificates, but a much
simpler format that encodes a public key, identity information and
some validity constraints and signs it with a CA key. CA keys are
regular SSH keys. This certificate style avoids the attack surface
of X.509 certificates and is very easy to deploy.
Certified host keys allow automatic acceptance of new host keys
when a CA certificate is marked as sh/known_hosts.
see VERIFYING HOST KEYS in ssh(1) for details.
Certified user keys allow authentication of users when the signing
CA key is marked as trusted in authorized_keys. See "AUTHORIZED_KEYS
FILE FORMAT" in sshd(8) for details.
Certificates are minted using ssh-keygen(1), documentation is in
the "CERTIFICATES" section of that manpage.
Documentation on the format of certificates is in the file
PROTOCOL.certkeys
feedback and ok markus@
[sshd.c packet.c serverloop.c monitor_wrap.c clientloop.c sshconnect.c
monitor.c Added roaming.h roaming_common.c roaming_dummy.c]
Keep track of number of bytes read and written. Needed for upcoming
changes. Most code from Martin Forssen, maf at appgate dot com.
ok markus@
Also, applied appropriate changes to Makefile.in
[auth.h auth2.c monitor.c monitor.h monitor_wrap.c monitor_wrap.h]
[readconf.c readconf.h servconf.c servconf.h ssh2.h ssh_config.5]
[sshconnect2.c sshd_config.5 jpake.c jpake.h schnorr.c auth2-jpake.c]
[Makefile.in]
Add support for an experimental zero-knowledge password authentication
method using the J-PAKE protocol described in F. Hao, P. Ryan,
"Password Authenticated Key Exchange by Juggling", 16th Workshop on
Security Protocols, Cambridge, April 2008.
This method allows password-based authentication without exposing
the password to the server. Instead, the client and server exchange
cryptographic proofs to demonstrate of knowledge of the password while
revealing nothing useful to an attacker or compromised endpoint.
This is experimental, work-in-progress code and is presently
compiled-time disabled (turn on -DJPAKE in Makefile.inc).
"just commit it. It isn't too intrusive." deraadt@
[monitor.c]
Clear key options in the monitor on failed authentication, prevents
applying additional restrictions to non-pubkey authentications in
the case where pubkey fails but another method subsequently succeeds.
bz #1472, found by Colin Watson, ok markus@ djm
[monitor.c monitor_wrap.c session.h servconf.c servconf.h session.c]
[sshd_config sshd_config.5]
Make the maximum number of sessions run-time controllable via
a sshd_config MaxSessions knob. This is useful for disabling
login/shell/subsystem access while leaving port-forwarding working
(MaxSessions 0), disabling connection multiplexing (MaxSessions 1) or
simply increasing the number of allows multiplexed sessions.
Because some bozos are sure to configure MaxSessions in excess of the
number of available file descriptors in sshd (which, at peak, might be
as many as 9*MaxSessions), audit sshd to ensure that it doesn't leak fds
on error paths, and make it fail gracefully on out-of-fd conditions -
sending channel errors instead of than exiting with fatal().
bz#1090; MaxSessions config bits and manpage from junyer AT gmail.com
ok markus@
[auth-options.c auth1.c channels.c channels.h clientloop.c gss-serv.c]
[monitor.c monitor_wrap.c nchan.c servconf.c serverloop.c session.c]
[ssh.c sshd.c]
Implement a channel success/failure status confirmation callback
mechanism. Each channel maintains a queue of callbacks, which will
be drained in order (RFC4253 guarantees confirm messages are not
reordered within an channel).
Also includes a abandonment callback to clean up if a channel is
closed without sending confirmation messages. This probably
shouldn't happen in compliant implementations, but it could be
abused to leak memory.
ok markus@ (as part of a larger diff)
[monitor_wrap.c monitor.c]
Send config block back to slave for invalid users too so options
set by a Match block (eg Banner) behave the same for non-existent
users. Found by and ok djm@
[auth-bsdauth.c auth-passwd.c auth.c auth.h auth1.c auth2-chall.c]
[monitor.c monitor_wrap.c]
unifdef -DBSD_AUTH
unifdef -USKEY
These options have been in use for some years;
ok markus@ "no objection" millert@
(NB. RCD ID sync only for portable)
[clientloop.c monitor.c monitor_fdpass.c monitor_fdpass.h]
[monitor_wrap.c ssh.c]
make file descriptor passing code return an error rather than call fatal()
when it encounters problems, and use this to make session multiplexing
masters survive slaves failing to pass all stdio FDs; ok markus@
[monitor.c]
pass received SIGINT from monitor to postauth child so it can clean
up properly. bz#1196, patch from senthilkumar_sen AT hotpop.com;
ok markus@
[monitor_wrap.c servconf.c servconf.h monitor.c sshd_config.5]
Teach Match how handle config directives that are used before
authentication. This allows configurations such as permitting password
authentication from the local net only while requiring pubkey from
offsite. ok djm@, man page bits ok jmc@
[monitor.c version.h]
correctly check for bad signatures in the monitor, otherwise the monitor
and the unpriv process can get out of sync. with dtucker@, ok djm@,
dtucker@
[monitor.c monitor_wrap.c]
Revert previous include file ordering change, for ssh to compile under
gcc2 (or until openssl include files are cleaned of parameter names
in function prototypes)
session.c ssh-rand-helper.c sshd.c openbsd-compat/bsd-cygwin_util.c
openbsd-compat/setproctitle.c] Convert malloc(foo*bar) -> calloc(foo,bar)
in Portable-only code; since calloc zeros, remove now-redundant memsets.
Also add a couple of sanity checks. With & ok djm@
[auth-bsdauth.c auth-skey.c auth.c auth2-chall.c channels.c]
[clientloop.c deattack.c gss-genr.c kex.c key.c misc.c moduli.c]
[monitor.c monitor_wrap.c packet.c scard.c sftp-server.c ssh-agent.c]
[ssh-keyscan.c ssh.c sshconnect.c sshconnect2.c sshd.c uuencode.c]
[xmalloc.c xmalloc.h]
introduce xcalloc() and xasprintf() failure-checked allocations
functions and use them throughout openssh
xcalloc is particularly important because malloc(nmemb * size) is a
dangerous idiom (subject to integer overflow) and it is time for it
to die
feedback and ok deraadt@
[channels.c monitor.c session.c session.h ssh-agent.c ssh-keygen.c]
[ssh-rsa.c ssh.c sshlogin.c]
annoying spacing fixes getting in the way of real diffs
