The binding is similar to the tv-binding, just with capital letters.
Switching the dvb-channel-name property compared to dvb-channel
means the channel-name is shown on-screen when switching instead of
"dvb-channel (error)" otherwise,
and switching anyways happens without changing the card.
window-scale is now mapped to Alt+0 etc. by default (although these
bindings just use "set", not "cycle-values").
colormatrix can't be cycled anymore (would require using vf_format).
Drop d for toggling framedrop. Toggling this is way too special to be at
such a prominent place, and in fact I believe toggling it is pointless.
Remap deinterlacing from D to d. It's relatively useful and non-
destructive.
As suggested in #973 (almost).
Nobody wanted to restore this, so it gets the boot.
If anyone still wants to volunteer to restore menu support, this would
be welcome. (I might even try it myself if I feel masochistic and like
wasting a lot of time for nothing.) But if it does get restored, it
should be done differently. There were many stupid things about how it
was done. For example, it somehow tried to pull mp_nav_events through
all the layers (including needing to "buffer" them in the demuxer),
which was needlessly complicated. It could be done simpler.
This code was already inactive, so this commit actually changes nothing.
Also keep in mind that normal DVD/BD playback still works.
The "osd" command cycles between 4 states (OSD level 0-3), which is
probably confusing and inconvenient. OSD levels 0 and 2 are rarely
needed. I would claim there is normally not much of a need to completely
disable OSD by setting level 0 during playback. Level 2 is just slightly
less information than level 3, and I'm not sure why it exists at all.
Change it so that it toggles between level 3 and 1. Note that this
ignores the default OSD level. If the default is 3, the first use of
this key will set it to 3 again. Just assume 1 is the default. If
someone complains, this could be improved.
Wnile it seems quite logical to me that commands use _ as word
separator, while properties use -, I can't really explain the
difference, and it tends to confuse users as well. So always
prefer - as separator for everything.
Using _ still works, and will probably forever. Not doing so would
probably create too much chaos and confusion.
This was mapped to a broken command, so it did nothing but printing an
error message. The intended binding (cycling OSD level) doesn't seem to
useful either, so just drop it.
Why did this exist in the first place? Other than being completely
useless, this even caused some regressions in the past. For example,
there was the case of a laptop exposing its accelerometer as joystick
device, which led to extremely fun things due to the default mappings of
axis movement being mapped to seeking.
I suppose those who really want to use their joystick to control a media
player (???) can configure it as mouse device or so.
This gets rid of the need for a second (or more) parameters; instead it
can be all in one parameter. The (now) redundant parameter is still
parsed for compatibility, though.
The way the flags make each other conflict is a bit tricky: they have
overlapping bits, and the option parser disallows setting already set
bits.
Apparently broken files are popular enough that this is still needed.
It's relatively often asked on the IRC channel, and I also found it on
the archwiki mpv page.
The list of aspect ratios is taken from the archwiki page, with "16:10"
removed (because I doubt there are actually files with this aspect
ratio).
It's just confusing; users are encouraged to edit input.conf instead
(changing the argument to the "add" command).
Update input.conf to keep the old behavior.
Apparently making ESC exit fullscreen mode is the more popular
convention compared to ESC quitting the program.
It was also concluded that ESC should do nothing when the windows is
already in normal state.
See discussion in #973.
Changing audio-delay is probably not needed.
Changing balance "works", but not as expected (sets up a pan matrix to
change left/right contributions to each other, rather than changing the
relative volumes of each channel).
I expect that the rest are not in use by anyone.
Nobody uses 'c' (except accidentally) - remove.
Everyone agrees that OSD level cycling on 'o' is dumb, so map it to
show_progress instead. Cycling the OSD level is now available on 'O'.
No reason to ummap 'P' yet.
Also see issue #973.
Convert all these commands to properties. (Except tv_last_channel, not
sure what to do with this.) Also, internally, don't access stream
details directly, but dispatch commands with stream ctrls.
Many of the new properties are a bit strange, because they're write-
only. Also remove some OSD output these commands produced, because I
couldn't be bothered to port these.
In general, this makes everything much cleaner, and will also make it
easier to e.g. move the demuxer to its own thread.
Don't bother updating input.conf, but changes.rst documents how old
commands map to the new ones.
Mostly untested, due to lack of hardware.
The window close button is usually mapped to the CLOSE_WIN pseudo-key.
Until now, --input-test treated this pseudo-key like any other key (like
the rest of the input handling code), so you couldn't close the window
in this mode. The manpage had silly instructions and warnings how to
deal with this.
Just always quit when CLOSE_WIN is received, and improve the
instructions.
This might be helpful if we ever want cascading config files. Also, we
will probably need it if we change the default input.conf bindings, and
want to provide compatibility input.conf files.
This readds a more or less completely new dvdnav implementation, though
it's based on the code from before commit 41fbcee. Note that this is
rather basic, and might be broken or not quite usable in many cases.
Most importantly, navigation highlights are not correctly implemented.
This would require changes in the FFmpeg dvdsub decoder (to apply a
different internal CLUT), so supporting it is not really possible right
now. And in fact, I don't think I ever want to support it, because it's
a very small gain for a lot of work. Instead, mpv will display fake
highlights, which are an approximate bounding box around the real
highlights.
Some things like mouse input or switching audio/subtitles stream using
the dvdnav VM are not supported.
Might be quite fragile on transitions: if dvdnav initiates a transition,
and doesn't give us enough mpeg data to initialize video playback, the
player will just quit.
This is added only because some users seem to want it. I don't intend to
make mpv a good DVD player, so the very basic minimum will have to do.
How about you just convert your DVD to proper video files?
This affects MOUSE_MOVE and MOUSE_LEAVE. Both are needed internally
(such as for the OSC), but not really useful for input.conf. Since the
warning has the purpose of notifying the user that a key is unmapped and
what key name to use for setting up a binding in input.conf, the warning
is rather useless in this case. It's also annoying in combination with
the
--no-input-default-bindings option, since that removes the default
bindings to "ignore" for these keys.
I suspect most users will just copy etc/input.conf when they want to
remap some default bindings. But usually this means the user even copies
bindings he doesn't care about, and it's better if the user maps only
the bindings in his input.conf the user intends to remap.
Comment all bindings in etc/input.conf. Since this file also defines the
builtin defaults and is baked into the mpv binary, we have to do
something to get them anyway, even though they are commented. Do this by
having input.c "uncomment" the bindings in the baked in input.conf. (Of
course this is done only for the builtin config, not configs loaded from
disk.)
