This moves all key codes above the highest valid unicode code point (which
is 0x10FFFF). All key codes below MP_KEY_BASE now directly map to unicode.
Configuration files (input.conf) can contain unicode characters in UTF-8
to map non-ASCII characters/keys.
This shouldn't change anything user visible, except that "direct key codes"
(as used in input.conf) will change their meaning.
Rework much of the logic related to reading from event sources and
queuing commands. The two biggest architecture changes are:
- The code buffering keycodes in mp_fifo.c is gone. Instead key input
is now immediately fed to input.c and interpreted as commands, and
then the commands are buffered instead.
- mp_input_get_cmd() now always tries to read every available event
from every event source and convert them to (buffered) commands.
Before it would only process new events until one new command became
available.
Some relevant behavior changes:
- Before commands could be lost when stream code called
mp_input_check_interrupt() which read commands (to see if they were
of types that triggered aborts during slow IO tasks) and then threw
them away. This was especially an issue if cache was enabled and slow
to read. Fixed - now it's possible to check whether there are queued
commands which will abort playback of the current file without
throwing other commands away.
- mp_input_check_interrupt() now prints a message if it returns
true. This is especially useful because the failures caused by
aborted stream reads can trigger error messages from other code that
was doing the read; the new message makes it more obvious what the
cause of the subsequent error messages is.
- It's now possible to again avoid making stdin non-blocking (which
caused some issues) without reintroducing extra latency. The change
will be done in a subsequent commit.
- Event sources that do not support select() should now have somewhat
lower latency in certain situations as they will be checked both
before and after select()/sleep in input reading; before the sleep
always happened first even if such sources already had queued
input. Before the key fifo was also handled in this manner (first
key triggered select, but if multiple were read then rest could be
delayed; however in most cases this didn't add latency in practice
as after central code started doing command handling it queried for
further commands with a max sleep time of 0).
- Key fifo limiting is more accurate now: it now counts actual
commands intead of keycodes, and all queued keys are read
immediately from input devices so they can be counted correctly.
- Since keypresses are now interpreted immediately, commands which
change keybindings will no longer affect following keypresses that
have already been read before the command is executed. This should
not be an issue in practice with current keybinding behavior.
Instead of strictly limiting the number of total entries in the
internal fifo, make the overall buffer bigger and try to limit entries
based on how many bound commands they're expected to generate. Now
doubleclick and button down events aren't counted for that limit.
Normally the sequence down-doubleclick-up generates at most one
command, so this better matches the quantity we actually want to
limit. Also add a mechanism to clear the button combination state kept
by input.c when the fifo is full; this avoids "stuck button" problems
due to button release events being dropped.
The key combination state clearing is partially based on MPlayer 1
changes by Reimar Döffinger (though overall the effects of this commit
are quite different). It still doesn't make "stuck button" problems
completely impossible; at least if the VO gets closed while a button
was down then nothing will send a button up event or reset state.
The code combining button presses into multibutton commands prevented
single click commands from triggering if a doubleclick event had been
generated from the same button press. As a result using the mouse
wheel to seek worked very badly. Special-case doubleclick events in
the event interpretation code to avoid this issue. This changes the
sequence of generated "keys" for press-release-press-release from
MOUSE_BTN0 MOUSE_BTN0-MOUSE_BTN0_DBL MOUSE_BTN0_DBL to
MOUSE_BTN0 MOUSE_BTN0_DBL MOUSE_BTN0.
"Keys" like MOUSE_BTN0-MOUSE_BTN0_DBL will never be generated now; any
existing configuration files using those need to be changed.
Move the definitions of all special key codes (those not passed by
ASCII value) to input/keycodes.h. Before they were spread between
osdep/keycodes.h, input/joystick.h, input/mouse.h and input/ar.h, plus
some special values in input.h. This was especially inconvenient as
the codes had to be coordinated to not conflict between the files.
The change requires a bit of ugliness as appleir.c includes
<linux/input.h> which contains various conflicting KEY_* definitions.
Work around this by adding a special preprocessor variable which can
be used to avoid defining these in keycodes.h.
Use the same mp_input_add_key_fd for all uses and add a context
argument to its callback that was before only in the event fd
callbacks. Instead of checking in input.c whether keys were inserted
to the keypress FIFO during the callback do the check in the callback
before returning and set return value accordingly.
"implicit declaration of function ‘mplayer_put_key’" warnings
Based on Attila's suggestions.
Approved by Uoti and Ivan.
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@22841 b3059339-0415-0410-9bf9-f77b7e298cf2
