mirror of
git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
synced 2024-12-13 18:58:11 +00:00
234 lines
5.6 KiB
Plaintext
234 lines
5.6 KiB
Plaintext
|
menu "General"
|
||
|
|
|
||
|
|
config CARL9170FW_RELEASE_VERSION
|
||
|
|
int
|
||
|
|
default 1
|
||
|
|
|
||
|
|
menu "Selectable Hardware Options"
|
||
|
|
|
||
|
|
choice
|
||
|
|
prompt "Receiver Max. Frame Length"
|
||
|
|
default CARL9170FW_RX_FRAME_LEN_8192
|
||
|
|
|
||
|
|
config CARL9170FW_RX_FRAME_LEN_4096
|
||
|
|
bool "4096"
|
||
|
|
|
||
|
|
config CARL9170FW_RX_FRAME_LEN_8192
|
||
|
|
bool "8192"
|
||
|
|
|
||
|
|
config CARL9170FW_RX_FRAME_LEN_16384
|
||
|
|
bool "16384"
|
||
|
|
|
||
|
|
config CARL9170FW_RX_FRAME_LEN_32768
|
||
|
|
bool "32768"
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
config CARL9170FW_RX_FRAME_LEN
|
||
|
|
int
|
||
|
|
default 4096 if CARL9170FW_RX_FRAME_LEN_4096
|
||
|
|
default 8192 if CARL9170FW_RX_FRAME_LEN_8192
|
||
|
|
default 16384 if CARL9170FW_RX_FRAME_LEN_16384
|
||
|
|
default 32768 if CARL9170FW_RX_FRAME_LEN_32768
|
||
|
|
|
||
|
|
config CARL9170FW_GPIO_INTERRUPT
|
||
|
|
def_bool y
|
||
|
|
prompt "GPIO Software Interrupt"
|
||
|
|
---help---
|
||
|
|
When this option is enabled, the firmware will poll the GPIO
|
||
|
|
registers and reports to the driver whenever the GPIO state
|
||
|
|
has changed from a previous state.
|
||
|
|
|
||
|
|
Note: This feature is necessary to monitor the WPS button,
|
||
|
|
if you have one on your device, then say Y.
|
||
|
|
|
||
|
|
config CARL9170FW_SECURITY_ENGINE
|
||
|
|
def_bool y
|
||
|
|
prompt "Support Hardware Crypto Engine"
|
||
|
|
---help---
|
||
|
|
This options controls if the firmware will allow the driver
|
||
|
|
to program the security engine / CAM through a firmware
|
||
|
|
interface.
|
||
|
|
|
||
|
|
Say Y. Unless you want to do the en- and decryption for
|
||
|
|
CCMP(AES), TKIP/WEP(RC4) in the application anyway.
|
||
|
|
|
||
|
|
config CARL9170FW_RADIO_FUNCTIONS
|
||
|
|
def_bool y
|
||
|
|
prompt "Enable Firmware-supported Radio/RF functions"
|
||
|
|
---help---
|
||
|
|
Some PHY/RF functions (e.g.: AGC and Noise calibration) need
|
||
|
|
to be done in the firmware.
|
||
|
|
|
||
|
|
Say Y, unless you really don't need the Radio/RF for
|
||
|
|
your project.
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
menu "802.11 Firmware Features"
|
||
|
|
|
||
|
|
config CARL9170FW_CAB_QUEUE
|
||
|
|
def_bool y
|
||
|
|
prompt "Support software-based Content after Beacon Queue"
|
||
|
|
---help---
|
||
|
|
This (software) queue is used to send any broad-/multi-cast buffered
|
||
|
|
frames after the next DTIM beacon.
|
||
|
|
|
||
|
|
This feature is required for Accesspoint mode operation.
|
||
|
|
|
||
|
|
Say Y.
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
source "carlfw/usb/Kconfig"
|
||
|
|
|
||
|
|
menu "Experimental, Unstable & Testing Extensions"
|
||
|
|
|
||
|
|
config CARL9170FW_PRINTF
|
||
|
|
def_bool y
|
||
|
|
prompt "Advanced printf"
|
||
|
|
depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB
|
||
|
|
---help---
|
||
|
|
Advanced printf (very useful for debugging purposes)
|
||
|
|
The formats supported by this implementation are:
|
||
|
|
'd' 'u' 'c' 's' 'x' 'X' 'p'.
|
||
|
|
|
||
|
|
Note: If this option is disabled, the firmware will be only
|
||
|
|
capable of reported _preformated_ string.
|
||
|
|
|
||
|
|
config CARL9170FW_EXPERIMENTAL
|
||
|
|
def_bool y
|
||
|
|
prompt "Experimental Features"
|
||
|
|
|
||
|
|
config CARL9170FW_WOL_OPTION
|
||
|
|
def_bool n
|
||
|
|
prompt "Wakeup on WLAN"
|
||
|
|
depends on CARL9170FW_EXPERIMENTAL
|
||
|
|
---help---
|
||
|
|
With this option enabled, the firmware can wake-up
|
||
|
|
suspended hosts... As long as they fully support
|
||
|
|
USB remote wakeup.
|
||
|
|
|
||
|
|
config CARL9170FW_WOL
|
||
|
|
def_bool n
|
||
|
|
depends on CARL9170FW_WOL_OPTION
|
||
|
|
|
||
|
|
config CARL9170FW_WOL_NL80211_TRIGGERS
|
||
|
|
def_bool n
|
||
|
|
prompt "Standard NL80211 wakeup triggers"
|
||
|
|
depends on CARL9170FW_WOL_OPTION
|
||
|
|
select CARL9170FW_WOL
|
||
|
|
---help---
|
||
|
|
Available triggers:
|
||
|
|
* Magic Packet(tm) pattern
|
||
|
|
* disconnect event
|
||
|
|
|
||
|
|
config CARL9170FW_WOL_PROBE_REQUEST
|
||
|
|
def_bool n
|
||
|
|
prompt "Probe Request"
|
||
|
|
depends on CARL9170FW_WOL_OPTION
|
||
|
|
select CARL9170FW_WOL
|
||
|
|
---help---
|
||
|
|
Scan probe requests for a given SSID.
|
||
|
|
|
||
|
|
config CARL9170FW_WOL_PROBE_REQUEST_SSID
|
||
|
|
string
|
||
|
|
prompt "Wakeup on WLAN SSID"
|
||
|
|
default "CARL9170_WAKEUP"
|
||
|
|
depends on CARL9170FW_WOL_PROBE_REQUEST
|
||
|
|
|
||
|
|
config CARL9170FW_VIFS_NUM
|
||
|
|
default 1
|
||
|
|
int
|
||
|
|
prompt "Number of additional pseudo virtual interfaces"
|
||
|
|
depends on CARL9170FW_EXPERIMENTAL
|
||
|
|
|
||
|
|
config CARL9170FW_FW_MAC_RESET
|
||
|
|
def_bool y
|
||
|
|
prompt "Firmware MAC Chip recovery"
|
||
|
|
depends on CARL9170FW_EXPERIMENTAL
|
||
|
|
|
||
|
|
config CARL9170FW_NOISY_MAC_RESET
|
||
|
|
def_bool n
|
||
|
|
prompt "Notify MAC RESET events"
|
||
|
|
depends on CARL9170FW_FW_MAC_RESET
|
||
|
|
|
||
|
|
config CARL9170FW_BROKEN_FEATURES
|
||
|
|
def_bool n
|
||
|
|
prompt "Broken Featurs"
|
||
|
|
|
||
|
|
config CARL9170FW_DEBUG
|
||
|
|
def_bool n
|
||
|
|
depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_PRINTF
|
||
|
|
prompt "Enable verbose debugging messages"
|
||
|
|
|
||
|
|
config CARL9170FW_DEBUG_LED_HEARTBEAT
|
||
|
|
def_bool n
|
||
|
|
prompt "LED Heartbeat"
|
||
|
|
depends on CARL9170FW_BROKEN_FEATURES
|
||
|
|
---help---
|
||
|
|
This option conflicts with the application's LED code.
|
||
|
|
Also, it assumes that you have two LEDs, which is not
|
||
|
|
necessarily true.
|
||
|
|
|
||
|
|
config CARL9170FW_DEBUG_UART
|
||
|
|
def_bool n
|
||
|
|
prompt "Pass debug messages through Highspeed UART"
|
||
|
|
depends on CARL9170FW_BROKEN_FEATURES
|
||
|
|
---help---
|
||
|
|
This option allows the firmware to send BUG/ERR/INFO/DBG and
|
||
|
|
hexdumps through the UART _as well_. However, first: you must
|
||
|
|
connect a working logger.
|
||
|
|
|
||
|
|
config CARL9170FW_WATCHDOG_BUTTON
|
||
|
|
def_bool n
|
||
|
|
depends on CARL9170FW_BROKEN && CARL9170FW_GPIO_INTERRUPT
|
||
|
|
prompt "Trigger Watchdog by pressing the WPS button"
|
||
|
|
|
||
|
|
choice CARL9170FW_UART_CLOCK
|
||
|
|
prompt "UART Clock"
|
||
|
|
depends on CARL9170FW_DEBUG_UART
|
||
|
|
default CARL9170FW_UART_CLOCK_40M
|
||
|
|
|
||
|
|
config CARL9170FW_UART_CLOCK_25M
|
||
|
|
bool "25"
|
||
|
|
|
||
|
|
config CARL9170FW_UART_CLOCK_40M
|
||
|
|
bool "40"
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
config CARL9170FW_UNUSABLE
|
||
|
|
def_bool y
|
||
|
|
depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
|
||
|
|
|
||
|
|
config CARL9170FW_USB_MODESWITCH
|
||
|
|
def_bool n
|
||
|
|
prompt "USB 1.1 / 2.0 switching support"
|
||
|
|
depends on CARL9170FW_BROKEN_FEATURES
|
||
|
|
---help---
|
||
|
|
Mostly implemented, but untested and some serious
|
||
|
|
doubts remain.
|
||
|
|
|
||
|
|
config CARL9170FW_DMA_QUEUE_BUMP
|
||
|
|
def_bool n
|
||
|
|
prompt "Bump a stuck TX queue before doing a MAC reset"
|
||
|
|
depends on CARL9170FW_BROKEN_FEATURES
|
||
|
|
|
||
|
|
menu "Build Options"
|
||
|
|
config CARL9170FW_AGGRESSIVE_CFLAGS
|
||
|
|
def_bool y
|
||
|
|
prompt "Enable aggressive size optimization"
|
||
|
|
---help---
|
||
|
|
This option adds several more optimization compiler flags,
|
||
|
|
which can greatly reduce the firmware size... at the expense
|
||
|
|
of machine-code readability.
|
||
|
|
|
||
|
|
Say Y. Else the firmware might not fit onto the device!
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
endmenu
|