hydrus/docs/Understanding_Database_Sync...

104 lines
8.6 KiB
Markdown
Raw Normal View History

# Understanding Database Synchronization Options
2021-12-22 22:31:23 +00:00
Tuning your database synchronization using the `--db_synchronous_override=0` launch argument can make Hydrus significantly faster with some caveats.
## Key Points
- This is a tutorial for advanced users who have read and understood this document and the risk/recovery procedure.
- It is nearly always safe to use `--db_synchronous_override=1` on any modern filesystem and this is the default.
- It is always more expensive to access the disk than doing things in memory. SSDs are 10-100x as slow as memory, and HDDs are 1000-10000x as slow as memory.
2021-12-22 22:31:23 +00:00
- If you turn synchronization to `0` you are gambling, but it is a safe gamble if you have a backup and **know exactly** what you are doing
- After running with synchronization set to zero you must either:
- Exit hydrus normally and let the OS flush disk caches (either by letting the system run/"idle" for a while, running `sync` on *NIX systems, or normal shutdown), or
- Restore the sqlite database files backup if **the OS shutdown abnormally**.
2021-12-22 22:31:23 +00:00
- Because of the potential for a lot of outstanding writes when using `synchronous=0`, other I/O on your system will slow down as the pending writes are interleaved. Normal shutdown may also take abnormally long because the system is flushing these pending writes, but you must allow it to take its time as explained in the section below.
**Note:** In historical versions of hydrus (`synchronous=2`), performance was terrible because hydrus would agressively (it was arguably somewhat paranoid) write changes to disk.
2021-12-22 22:31:23 +00:00
## The Secret Sauce
Setting the synchronous to 0 lets the database engine defer writing to disk as long as physically possible. In the normal operation of your system, files are constantly being partially transfered to disk, even if the OS pretends they have been fully written to disk. This is called write cache and it is really important to use it or your system's performance would be terrible. The caveat is that until you have "`synced`" the disk cache, the changes to files are not actually in permanent storage. One purpose of a normal shutdown of the operating system is to make sure all disk caches have been flushed and synced. A program can also request that a file it has just written to be flushed, and it will wait until that is done before continuing.
2021-12-22 22:31:23 +00:00
When not in synchronous 0 mode, the database engine flushes at regular intervals to make sure data has been written.
- Setting synchronous to 0 is generally safe **if and only if** the system also shuts down normally, allowing any of these pending writes to be flushed.
- The database can back out of partial changes if hydrus crashes **even if** `synchronous=0`, so your database will not go corrupt from hydrus shutting down abnormally, only from the system shutting down abnormally.
## Technical Explanation
Programmers are responsible for handling partially written files, but this is tedious for large complex data, so they use a database engine which handles all of this. The database ensures that any partially written data is reversible to a known state (called a rollback).
An existing file may be in 3 possible states:
- **Unflushed**: Contents os owned by the program writing the file, but control returns immediately to the program instead of waiting for a full write. Content can be transitioned from unflushed to flushed using `fflush(FILE)`, `fflush()` is called automatically when a programmer closes a file, or exits the program normally(under most runtimes but not for example in Java). If the program exits abnormally before data is flushed it will be lost when the program crashes.
- **Flushed**: Pending write to permenant storage but memory has been transfered to the operating system. Data will not be lost if the calling program crashes, since the OS promises it will "eventually" arrive on disk before returning from `fflush()`. When you "safely shutdown:, you are instructing the OS among other things to sync the flushed files. If someone decides to read a file before it has been synced the OS will read the contents up until the flush from the flush buffer, and return that instead of what is actually on disk. If the OS crashes due to error or power failure, files that are flushed but not synced will be lost.
- **Synced**: Written to permenant storage. A programmer may request that the contents of the file be synced, or it is done gradually over time to free the OS buffers
To ensure the consistency of the database and rollback when needed, the database engine keeps a **journal** of what it is doing. Each transaction ends in a `flush` followed by a `sync`. The *flush* ensures that everything written before the flush will not occur before the line that indicats the transaction completed. The *sync* ensures that the entire contents of the transaction has been written to permenant storage before proceeding. The OS is not obligated to write chunks of the database file in the order it recieves them. It only guarentees that if you flush everything before the flush happens first, and everything after happens next.
The sync is what is controlled by the `synchronous` switch. Allowing the database to ignore whether sync actually completes is the magic that makes `synchronous=0` so dang fast.
2021-12-22 22:31:23 +00:00
### An example journal
1. Begin Transaction 1
2. Write Change 1
3. Write Change 2
4. Read data
5. Write Change 3
6. End Transaction 1
Each of these steps are performed in order. Suppose a crash occcured mid writing
1. Begin Transaction 1
2. Write Change 1
3. Write Cha
When the database resumes it will start scanning the journal at step 1. Since it will reach the end without seeing `End Transaction 1` it knows that data was only partialy written, and can put the data back in the state before transaction 1 began. This property of a database is called **atomicity** in the sense that something **atomic** is "indivisible"; either all of the steps in transaction 1 occur or non of them occur.
Hydrus is structured in such a way that the database is written to to keep track of your file catalog only once the file has been fully imported and moved where it is supposed to be. Thus every action hydrus takes is kept "atomic" or "repeatable" (redo existing work that was partway through). If hydrus crashes in the middle of importing a file, then when it resumes, as far as it is aware, it didn't even start importing the file. It will repeat the steps from the start until the file catalog is "consistent" with what is on disk.
### Where synchronization comes in
Lets revisit the journal, this time with two transactions. Note that the database is syncing on step 8 and thus will have to wait for the OS to write to disk before proceeding, holding up transaction 2, and any other access to the database.
2021-12-22 22:31:23 +00:00
1. Begin Transaction 1
2. Write Change 1
3. Write Change 2
4. Read data
5. Write Change 3
6. FLUSH
7. End Transaction 1
8. SYNC
2021-12-22 22:31:23 +00:00
9. Begin Transaction 2
10. Write Change 2
11. Write Change 2
12. Read data
13. Write Change 3
14. FLUSH
15. End Transaction 2
16. SYNC
2021-12-22 22:31:23 +00:00
**What happens if we remove step 6 and 8 and then die at step 11?**
1. Begin Transaction 1
2. Write Change 1
3. Write Change 2
4. Read data
5. Write Change 3
2021-12-23 13:53:24 +00:00
6. ~~FLUSH~~
2021-12-22 22:31:23 +00:00
7. End Transaction 1
8. ~~SYNC~~
2021-12-22 22:31:23 +00:00
9. Begin Transaction 2
10. Write Change 2
11. Write Ch
What if we crash and step, `End Transaction` has not been written to disk. Now not only do we need to repeat transaction 2, we also need to repeat transaction 1. Note that **this just increaeses the ammount of repeatable work, and actually is fully recoverable** (assuming a file you were downloading didn't cease to exist in the interim).
**Now what happens if we do the above and the OS crashes?**
The OS is not obligated to write chunks of the database file in the order you give them to it, in fact for harddrives it is optimal to scatter chunks of the file around the spinning disks so it might arbitrarily reorder your write calls.
- The only way you can be certain that all of the changes in the transaction have been written before writing `END Transaction` is to `flush()`
- The only way you can be sure `END Transaction` was written before doing more changes is to `sync()`.
Thus if the OS crashes at the exact wrong moment, there is no way to be sure that the journal is correct if flushing was skipped (`synchronous=0`). **This means there is no way for you to determine whether the database file is correct after a system crash if you had synchronous 0, and you MUST restore your files from backup as this will be the ONLY WAY to know they are in a known good state.**
2021-12-22 22:31:23 +00:00
So, setting `synchronous=0` gets you a pretty huge speed boost, but you are gambling that everything goes perfectly and will pay the price of a manual restore every time it doesn't.