289 lines
8.5 KiB
Plaintext
289 lines
8.5 KiB
Plaintext
Haproxy's peers v2.0 protocol 08/18/2016
|
|
|
|
Author: Emeric Brun ebrun@haproxy.com
|
|
|
|
|
|
I) Encoded Integer and Bitfield.
|
|
|
|
|
|
0 <= X < 240 : 1 byte (7.875 bits) [ XXXX XXXX ]
|
|
240 <= X < 2288 : 2 bytes (11 bits) [ 1111 XXXX ] [ 0XXX XXXX ]
|
|
2288 <= X < 264432 : 3 bytes (18 bits) [ 1111 XXXX ] [ 1XXX XXXX ] [ 0XXX XXXX ]
|
|
264432 <= X < 33818864 : 4 bytes (25 bits) [ 1111 XXXX ] [ 1XXX XXXX ]*2 [ 0XXX XXXX ]
|
|
33818864 <= X < 4328786160 : 5 bytes (32 bits) [ 1111 XXXX ] [ 1XXX XXXX ]*3 [ 0XXX XXXX ]
|
|
|
|
|
|
|
|
|
|
I) Handshake
|
|
|
|
Each peer try to connect to each others, and each peer is listening
|
|
for a connect from other peers.
|
|
|
|
|
|
Client Server
|
|
Hello Message
|
|
------------------------>
|
|
|
|
Status Message
|
|
<------------------------
|
|
|
|
1) Hello Message
|
|
|
|
Hello message is composed of 3 lines:
|
|
|
|
<protocol> <version>
|
|
<remotepeerid>
|
|
<localpeerid> <processpid> <relativepid>
|
|
|
|
protocol: current value is "HaproxyS"
|
|
version: current value is "2.0"
|
|
remotepeerid: is the name of the target peer as defined in the configuration peers section.
|
|
localpeerid: is the name of the local peer as defined on cmdline or using hostname.
|
|
processid: is the system process id of the local process.
|
|
relativepid: is the haproxy's relative pid (0 if nbproc == 1)
|
|
|
|
2) Status Message
|
|
|
|
Status message is a code followed by a LF.
|
|
|
|
200: Handshake succeeded
|
|
300: Try again later
|
|
501: Protocol error
|
|
502: Bad version
|
|
503: Local peer name mismatch
|
|
504: Remote peer name mismatch
|
|
|
|
|
|
IV) Messages
|
|
|
|
Messages:
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16
|
|
Message Class| Message Type
|
|
|
|
if Message Type >= 128
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16 .....
|
|
Message Class| Message Type | encoded data length | data
|
|
|
|
Message Classes:
|
|
0: control
|
|
1: error
|
|
10: related to stick table updates
|
|
255: reserved
|
|
|
|
|
|
1) Control Messages Class
|
|
|
|
Available message Types for class control:
|
|
0: resync request
|
|
1: resync finished
|
|
2: resync partial
|
|
3: resync confirm
|
|
|
|
|
|
a) Resync Request Message
|
|
|
|
This message is used to request a full resync from a peer
|
|
|
|
b) Resync Finished Message
|
|
|
|
This message is used to signal remote peer that locally known updates have been pushed, and local peer was considered up to date.
|
|
|
|
c) Resync Partial Message
|
|
|
|
This message is used to signal remote peer that locally known updates have been pushed, and but the local peer is not considered up to date.
|
|
|
|
d) Resync Confirm Message
|
|
|
|
This message is an ack for Resync Partial or Finished Messages.
|
|
|
|
It's allow the remote peer to go back to "on the fly" update process.
|
|
|
|
|
|
2) Messages Class
|
|
|
|
Available message Types for this class are:
|
|
0: protocol error
|
|
1: size limit reached
|
|
|
|
a) Protocol Message
|
|
|
|
To signal that a protocol error occurred. Connection will be shutdown just after sending this message.
|
|
|
|
b) Size Limit Error Message
|
|
|
|
To signal that a message is outsized and can not be correctly handled. Connection will be broken.
|
|
|
|
|
|
|
|
3) Stick Table Updates Messages Class
|
|
|
|
Available message Types for this class are:
|
|
0: Entry update
|
|
1: Incremental entry update
|
|
2: table definition
|
|
3: table switch
|
|
4: updates ack message.
|
|
|
|
|
|
a) Update Message
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16 .....
|
|
Message class | Message Type | encoded data length | data
|
|
|
|
|
|
data is composed like this
|
|
|
|
0 - - - - - - - 32 .............................
|
|
Local Update ID | Key value | data values ....
|
|
|
|
Update ID in a 32bits identifier of the local update.
|
|
|
|
Key value format depends of the table key type:
|
|
|
|
- for keytype string
|
|
|
|
0 .................................
|
|
encoded string length | string value
|
|
|
|
- for keytype integer
|
|
0 - - - - - - - - - - 32
|
|
encoded integer value |
|
|
|
|
- for other key type
|
|
|
|
The value length is annonced in table definition message
|
|
0 ....................
|
|
value
|
|
|
|
|
|
b) Incremental Update Message
|
|
|
|
Same format than update message except the Update ID is not present, the receiver should
|
|
consider that the update ID is an increment of 1 of the previous considered update message (partial or not)
|
|
|
|
|
|
c) Table Definition Message
|
|
|
|
This message is used by the receiver to identify the stick table concerned by next update messages and
|
|
to know which data is pushed in these updates.
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16 .....
|
|
Message class | Message Type | encoded data length | data
|
|
|
|
|
|
data is composed like this
|
|
|
|
0 ...................................................................
|
|
Encoded Sender Table Id | Encoded Local Table Name Length | Table Name | Encoded Table Type | Encoded Table Keylen | Encoded Table Data Types Bitfield
|
|
|
|
|
|
Encoded Sender Table ID present a the id numerical ID affected to that table by the sender
|
|
It will be used by "Updates Aknowlegement Messages" and "Table Switch Messages".
|
|
|
|
Encoded Local Table Name Length present the length to read the table name.
|
|
|
|
"Table Name" is the shared identifier of the table (name of the current table in the configuration)
|
|
It permits the receiver to identify the concerned table. The receiver should keep in memory the matching
|
|
between the "Sender Table ID" to identify it directly in case of "Table Switch Message".
|
|
|
|
Table Type present the numeric type of key used to store stick table entries:
|
|
integer
|
|
0: signed integer
|
|
1: IPv4 address
|
|
2: IPv6 address
|
|
3: string
|
|
4: binary
|
|
|
|
Table Keylen present the key length or max length in case of strings or binary (padded with 0).
|
|
|
|
Data Types Bitfield present the types of data linearly pushed in next updates message (they will be linearly pushed in the update message)
|
|
Known types are
|
|
bit
|
|
0: server id
|
|
1: gpt0
|
|
2: gpc0
|
|
3: gpc0 rate
|
|
4: connections counter
|
|
5: connection rate
|
|
6: number of current connections
|
|
7: sessions counter
|
|
8: session rate
|
|
9: http requests counter
|
|
10: http requests rate
|
|
11: errors counter
|
|
12: errors rate
|
|
13: bytes in counter
|
|
14: bytes in rate
|
|
15: bytes out rate
|
|
16: bytes out rate
|
|
17: gpc1
|
|
18: gpc1 rate
|
|
|
|
d) Table Switch Message
|
|
|
|
After a Table Message Define, this message can be used by the receiver to identify the stick table concerned by next update messages.
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16 .....
|
|
Message class | Message Type | encoded data length | data
|
|
|
|
|
|
data is composed like this
|
|
|
|
|
|
0 .....................
|
|
encoded Sender Table Id
|
|
|
|
c) Update Ack Message
|
|
|
|
0 - - - - - - - 8 - - - - - - - 16 .....
|
|
Message class | Message Type | encoded data length | data
|
|
|
|
data is composed like this
|
|
|
|
0 ....................... - - - - - - - - 32
|
|
Encoded Remote Table Id | Update Id
|
|
|
|
|
|
Remote Table Id is the numeric identifier of the table on the remote side.
|
|
Update Id is the id of the last update locally committed.
|
|
|
|
If a re-connection occurred, the sender should know he will have to restart the push of updates from this point.
|
|
|
|
III) Initial full resync process.
|
|
|
|
|
|
a) Resync from local old process
|
|
|
|
An old soft-stopped process will close all established sessions with remote peers and will try to connect to a new
|
|
local process to push all known ending with a Resync Finished Message or a Resync Partial Message (if it it does not consider itself as full updated).
|
|
|
|
A new process will wait for a an incoming connection from a local process during 5 seconds. It will learn the updates from this
|
|
process until he will receive a Resync Finished Message or a Resync Partial Message. If it receive a Resync Finished Message it will consider itself
|
|
as fully updated and stops to ask for resync. If it receive a Resync Partial Message it will wait once again for 5 seconds for an other incoming connection from a local process.
|
|
Same thing if the session was broken before receiving any "Resync Partial Message" or "Resync Finished Message".
|
|
|
|
If one of these 5 seconds timeout expire, the process will try to request resync from a remote connected peer (see b). The process will wait until 5seconds
|
|
if no available remote peers are found.
|
|
|
|
If the timeout expire, the process will consider itself ass fully updated
|
|
|
|
b) Resync from remote peers
|
|
|
|
The process will randomly choose a remote connected peer and ask for a full resync using a Resync Request Message. The process will wait until 5seconds
|
|
if no available remote peers are found.
|
|
|
|
The chosen remote peer will push its all known data ending with a Resync Finished Message or a Resync Partial Message (if it it does not consider itself as full updated).
|
|
|
|
If it receive a Resync Finished Message it will consider itself as fully updated and stops to ask for resync.
|
|
|
|
If it receive a Resync Partial Message, the current peer will be flagged to anymore be requested and any other connected peer will be randomly chosen for a resync request (5s).
|
|
|
|
If the session is broken before receiving any ot these messages any other connected peer will be randomly chosen for a resync request (5s).
|
|
|
|
If the timeout expire, the process will consider itself as fully updated
|
|
|
|
|