The quick build reminders claimed to present "all options" but were
still missing QUIC. It was also the moment to split FreeBSD and
OpenBSD apart since the latter uses LibreSSL and does not require
the openssl compatibility wrapper. We also replace the hard-coded
number of cpus for the parallel build, by the real number reported
by the system.
The doc about the build process has grown to a point where it was painful
to read when searching a specific element. This commit cuts it into a few
sub-categories for ease of searching, and it also adds a summary of the
most commonly used makefile variables, their usage and default settings.
This one is often used as a gateway to inject regular CFLAGS, even though
not designed for this. It's now ignored, but any attempt at setting it
reports a warning suggesting to use CFLAGS or ARCH_FLAGS instead.
It's currently not possible to only set some -Wno... without breaking
the -W... and conversely. Let's split both sets apart so that it's now
possible to set -W... alone in WARN_CFLAGS to enable only some warnings,
and pass the -Wno... in SPEC_CFLAGS without losing the enabled ones.
-Wfatal-errors is set by default and is not supported on older compilers.
Since it's part of all the automatically detected flags, it's painful to
remove when needed. Also it's a matter of taste, some developers might
prefer to get a long list of all errors at once, others prefer that the
build stops immediately after the root cause.
The default is now back to no -Wfatal-errors, and when FAILFAST is set to
any non-empty non-zero value, -Wfatal-errors is added:
$ make TARGET=linux-glibc USE_OPENSSL=0 USE_QUIC=1 FAILFAST=0 2>&1 | wc
132 536 6111
$ make TARGET=linux-glibc USE_OPENSSL=0 USE_QUIC=1 FAILFAST=1 2>&1 | wc
8 39 362
It's among the options that change a lot on the developer's side and it's
tempting to change from ERR=1 to ERR=0 on the make command line by reusing
the history, except it doesn't work. Let's explictily permit ERR=0 to
disable -Werror like ERR= does.
ARCH_FLAGS used to be merged into LDFLAGS so that it was not possible to
pass extra options to LDFLAGS without losing ARCH_FLAGS. This commit now
splits them apart and leaves LDFLAGS empty by default. The doc explains
how to use it for rpath and such occasional use cases.
ARCH_FLAGS was always present and is documented as being fed to both
CC and LD during the build. This is meant for options that need to be
consistent between the two stages such as -pg, -flto, -fsanitize=address,
-m64, -g etc. Its doc was lacking a bit of clarity though, and it was
not enumerated in the makefile's variables list.
ARCH however was only documented as affecting ARCH_FLAGS, and was just
never used as the only two really usable and supported ARCH_FLAGS options
were -m32 and -m64. In addition it was even written in the makefile that
it was CPU that was affecting the ARCH_FLAGS. Let's just drop ARCH and
improve the documentation on ARCH_FLAGS. Again, if ARCH is set, a warning
is emitted explaining how to proceed.
ARCH_FLAGS is now preset to -g so that we finally have a correct place
to deal with such debugging options that need to be passed to both
stages. The fedora and musl CI workflows were updated to also use it
instead of sticking to duplicate DEBUG_CFLAGS+LDFLAGS.
It's also worth noting that BUILD_ARCH was being passed to the build
process and never used anywhere in the code, so its removal will not
be noticed.
The CPU variable, when used, is almost always exclusively used with
"generic" to disable any CPU-specific optimizations, or "native" to
enable "-march=native". Other options are not used and are just making
CPU_CFLAGS more confusing.
This commit just drops all pre-configured variants and replaces them
with documentation about examples of supported options. CPU_CFLAGS is
preserved as it appears that it's mostly used as a proxy to inject the
distro's CFLAGS, and it's just empty by default.
The CPU variable is checked, and if set to anything but "generic", it
emits a warning about its deprecation and invites the user to read
INSTALL.
Users who would just set CPU_CFLAGS will be able to continue to do so,
those who were using CPU=native will have to pass CPU_CFLAGS=-march=native
and those who were passing one of the other options will find it in the
doc as well.
Note that this also removes the "CPU=" line from haproxy -vv, that most
users got used to seeing set to "generic" or occasionally "native"
anyway, thus that didn't provide any useful information.
CPU_CFLAGS is meant to set the CPU-specific options (-mcpu, -march etc).
The fact that it also includes the optimization level is annoying because
one cannot be set without replacing the other. Let's move the optimization
level to a new independent OPT_CFLAGS that is added early to the list, so
that other CFLAGS (including CPU_CFLAGS) can continue to override it if
necessary.
These settings were appended to the final build CFLAGS and used to
contain a mix of obsolete settings that can equally be passed in one
of the many other variables such as DEFINE or more recently CFLAGS.
Let's just drop the obsolete comment about it, and check if anything
was forced there, then emit a warning suggesting to move that to other
variables such as DEFINE or CFLAGS, so as to be kind to package
maintainers.
CFLAGS has always been a troublemaker because the variable was preset
based on other options, including dynamically detected ones, so
overriding it would just lose the original contents, forcing users
to resort to various alternatives such as DEFINE, ADDINC or SMALL_OPTS.
Now that the variable's usage was cleared, let's just preset it to
empty (and it MUST absolutely remain like this) and append it at the
end of the compiler's options. This will now allow to change an
optimization level, force a CPU type or disable a warning as users
commonly expect from CFLAGS passed to a makefile, and not to override
*all* the compiler flags as it has progressively become.
This option has been set by default for a very long time and also
complicates the manipulation of the DEBUG variable. Let's make it
the official default and permit to unset it by setting it to zero.
The other pool-related DEBUG options were adjusted to also explicitly
check for the zero value for consistency.
We continue to carry it in the makefile, which adds to the difficulty
of passing new options. Let's make DEBUG_STRICT=1 the default so that
one has to explicitly pass DEBUG_STRICT=0 to disable it. This allows us
to remove the option from the default DEBUG variable in the makefile.
William rightfully reported that not supporting =0 to disable a USE_xxx
option is sometimes painful (e.g. a script might do USE_xxx=$(command)).
It's not that difficult to handle actually, we just need to consider the
value 0 as empty at the few places that test for an empty string in
options.mk, and in each "ifneq" test in the main Makefile, so let's do
that. We even take care of preserving the original value in the build
options string so that building with USE_OPENSSL=0 will be reported
as-is in haproxy -vv, and with "-OPENSSL" in the feature list.
This adds a new option for the Makefile USE_OPENSSL_AWSLC, and
update the documentation with instructions to use HAProxy with
AWS-LC.
Update the type of the OCSP callback retrieved with
SSL_CTX_get_tlsext_status_cb with the actual type for
libcrypto versions greater than 1.0.2. This doesn't affect
OpenSSL which casts the callback to void* in SSL_CTX_ctrl.
Let's make clear which commands goes into the wolfSSL directory and
which one in the haproxy directory. Also, let's add a paragraph in the
QUIC section explaining how to proceed with wolfSSL.
In the errors and warnings section about common issues, it's useful to
mention the strict-aliasing warning that was happening with gcc-4.4 that
may still be found on old systems, especially since it will probably take
ages to build there and the warning is harmless.
Gcc 13 is known to work, OpenSSL 3.1 and wolfSSL as well. Add a few
hints about build errors when using QUIC + OpenSSL and warnings about
the dramatic OpenSSL 3.x performance regression.
OpenSSL 3.0 is now supported but was not mentioned. Also, it was
found that OpenSSL 0.9.8 doesn't build anymore since 2.5 due to
some of the functions used in the JWT token processing, and since
nobody complained, it seems it's not worth fixing it so support for
it was removed.
It turns out that gcc-3.4 doesn't build anymore (and it has probably been
the case since 2.4 or so). gcc-4.2 does build fine though, let's mark it
as the oldest supported one. Now that gcc-12 works, also update the most
recently known-to-work version.
SSL engines used to be built by default for a long time but they're now
disabled consecutive to the API change that makes OpenSSL 3.0 spew plenty
of warnings. Support may still be enabled by passing USE_ENGINE=1.
This enumerates a few of the options that are expected to have an effect
on the process' self-checks at the expense of more or less performance,
and how to choose sets of options for different deployments.
