The s1 server is acting like a SMTP server. But it sends two CRLF at the end of
each line, while only one CRLF must be returned. It only works becaue both CRLF
are received at the same time.
Tests with forced wakeups on a 24c/48t machine showed that we're caping
at 7.3M loops/s, which means 6.6 microseconds of loop delay without
having anything to do.
This is caused by two factors:
- the load and update of the now_offset variable
- the update of the global_now variable
What is happening is that threads are not running within the one-
microsecond time precision provided by gettimeofday(), so each thread
waking up sees a slightly different date and causes undesired updates
to global_now. But worse, these undesired updates mean that we then
have to adjust the now_offset to match that, and adds significant noise
to this variable, which then needs to be updated upon each call.
By only allowing sightly less precision we can completely eliminate
that contention. Here we're ignoring the 5 lowest bits of the usec
part, meaning that the global_now variable may be off by up to 31 us
(16 on avg). The variable is only used to correct the time drift some
threads might be observing in environments where CPU clocks are not
synchronized, and it's used by freq counters. In both cases we don't
need that level of precision and even one millisecond would be pretty
fine. We're just 30 times better at almost no cost since the global_now
and now_offset variables now only need to be updated 30000 times a
second in the worst case, which is unnoticeable.
After this change, the wakeup rate jumped from 7.3M/s to 66M/s, meaning
that the loop delay went from 6.6us to 0.73us, that's a 9x improvement
when under load! With real tasks we're seeing a boost from 28M to 52M
wakeups/s. The clock_update_global_date() function now only takes
1.6%, it's good enough so that we don't need to go further.
This patch modifies epoll, kqueue and evports (the 3 pollers that support
busy polling) to only update the local date in the inner polling loop,
the global one being done when leaving the loop. Testing with epoll on
a 24c/48t machine showed a boost from 53M to 352M loops/s, indicating
that the loop was spending 85% of its time updating the global date or
causing side effects (which was confirmed with perf top showing 67% in
clock_update_global_date() alone).
Pollers that support busy polling spend a lot of time (and cause
contention) updating the global date when they're looping over themselves
while it serves no purpose: what's needed is only an update on the local
date to know when to stop looping.
This patch splits clock_pudate_date() into a pair of local and global
update functions, so that pollers can be easily improved.
Patrick Hemmer reported an improper log behavior when using
log-format to escape log data (+E option):
Some bytes were truncated from the output:
- escape_string() function now takes an extra parameter that
allow the caller to specify input string stop pointer in
case the input string is not guaranteed to be zero-terminated.
- Minors checks were added into lf_text_len() to make sure dst
string will not overflow.
- lf_text_len() now makes proper use of escape_string() function.
This should be backported as far as 1.8.
The commit 372b38f935 ("BUG/MEDIUM: mux-h1: Handle connection error after a
synchronous send") introduced a bug. In h1_snd_buf(), consumed data are not
properly accounted if a connection error is detected. Indeed, data are
consumed when the output buffer is filled. But, on connection error, we exit
from the loop without incremented total variable accordingly.
When this happens, this leaves the channel buffer in an inconsistent
state. The buffer may be empty with some output at the channel level.
Because an error is reported, it is harmless. But it is safer to fix this
bug now to avoid any regression in future.
This patch must be backported as far as 2.2.
MUX QUIC snd_buf operation whill return early if a qcs instance is
resetted. In this case, HTX is left untouched and the callback returns
the whole bufer size. This lead to an undefined behavior as the stream
layer is notified about a transfer but does not see its HTX buffer
emptied. In the end, the transfer may stall which will lead to a leak on
session.
To fix this, HTX buffer is now resetted when snd_buf is short-circuited.
This should fix the issue as now the stream layer can continue the
transfer until its completion.
This patch has already been tested by Tristan and is reported to solve
the github issue #1801.
This should be backported up to 2.6.
Factorize common code between h3 and hq-interop snd_buf operation. This
is inserted in MUX QUIC snd_buf own callback.
The h3/hq-interop API has been adjusted to directly receive a HTX
message instead of a plain buf. This led to extracting part of MUX QUIC
snd_buf in qmux_http module.
This should be backported up to 2.6.
Extract function dealing with HTX outside of MUX QUIC. For the moment,
only rcv_buf stream operation is concerned.
The main objective is to be able to support both TCP and HTTP proxy mode
with a common base and add specialized modules on top of it.
This should be backported up to 2.6.
QUIC MUX implements several APIs to interface with stream, quic-conn and
app-ops layers. It is planified to better separate this roles, possibly
by using several files.
The first step is to extract QUIC MUX traces in a dedicated source
files. This will allow to reuse traces in multiple files.
The main objective is to be
able to support both TCP and HTTP proxy mode with a common base and add
specialized modules on top of it.
This should be backported up to 2.6.
A qcs instance free may be postponed in stream detach operation if the
stream is not locally closed. This condition is there to achieve
transfering data still present in Tx buffer. Once all data have been
emitted to quic-conn layer, qcs instance can be released.
However, the stream is only closed locally if HTX EOM has been seen or
it has been resetted. In case the transfer finished without EOM, a
detached qcs won't be freed even if there is no more activity on it.
This bug was not reproduced but was found on code analysis. Its precise
impact is unknown but it should not cause any leak as all qcs instances
are freed with its parent qcc connection : this should eventually happen
on MUX timeout or QUIC idle timeout.
To adjust this, condition to mark a stream as locally closed has been
extended. On qcc_streams_sent_done() notification, if its Tx buffer has
been fully transmitted, it will be closed if either FIN STREAM was set
or the stream is detached.
This must be backported up to 2.6.
Some tables are currently used to decode bit blocks and lengths. We do
see such lookups in perf top. We have 4 512-byte tables and one 64-byte
one. Looking closer, the second half of the table (length) has so few
variations that most of the time it will be computed in a single "if",
and never more than 3. This alone allows to cut the tables in half. In
addition, one table (bits 15-11) is only 32-element long, while another
one (bits 11-4) starts at 0x60, so we can merge the two as they do not
overlap, and further save size. We're now down to 4 256-entries tables.
This is visible in h3 and h2 where the max request rate is slightly higher
(e.g. +1.6% for h2). The huff_dec() function got slightly larger but the
overall code size shrunk:
$ nm --size haproxy-before | grep huff_dec
000000000000029e T huff_dec
$ nm --size haproxy-after | grep huff_dec
0000000000000345 T huff_dec
$ size haproxy-before haproxy-after
text data bss dec hex filename
7591126 569268 2761348 10921742 a6a70e haproxy-before
7591082 568180 2761348 10920610 a6a2a2 haproxy-after
The locally defined static variables 'httpclient_srv_raw' and
'httpclient_srv_ssl' are not used anywhere in the source code,
except that they are set in the httpclient_precheck() function.
nb_hreq is a counter on qcc for active HTTP requests. It is incremented
for each qcs where a full HTTP request was received. It is decremented
when the stream is closed locally :
- on HTTP response fully transmitted
- on stream reset
A bug will occur if a stream is resetted without having processed a full
HTTP request. nb_hreq will be decremented whereas it was not
incremented. This will lead to a crash when building with
DEBUG_STRICT=2. If BUG_ON_HOT are not active, nb_hreq counter will wrap
which may break the timeout logic for the connection.
This bug was triggered on haproxy.org. It can be reproduced by
simulating the reception of a STOP_SENDING frame instead of a STREAM one
by patching qc_handle_strm_frm() :
+ if (quic_stream_is_bidi(strm_frm->id))
+ qcc_recv_stop_sending(qc->qcc, strm_frm->id, 0);
+ //ret = qcc_recv(qc->qcc, strm_frm->id, strm_frm->len,
+ // strm_frm->offset.key, strm_frm->fin,
+ // (char *)strm_frm->data);
To fix this bug, a qcs is now flagged with a new QC_SF_HREQ_RECV. This
is set when the full HTTP request is received. When the stream is closed
locally, nb_hreq will be decremented only if this flag was set.
This must be backported up to 2.6.
Released version 2.7-dev6 with the following main changes :
- MINOR: Revert part of clarifying samples support per os commit
- BUILD: makefile: enable crypt(3) for NetBSD
- BUG/MINOR: quic: Retransmitted frames marked as acknowledged
- BUG/MINOR: quic: Possible crash with "tls-ticket-keys" on QUIC bind lines
- MINOR: http-check: Remove support for headers/body in "option httpchk" version
- BUG/MINOR: h1: Support headers case adjustment for TCP proxies
- BUG/MINOR: quic: Possible crash when verifying certificates
- BUILD: quic: add some ifdef around the SSL_ERROR_* for libressl
- BUILD: ssl: fix ssl_sock_switchtx_cbk when no client_hello_cb
- BUILD: quic: temporarly ignore chacha20_poly1305 for libressl
- BUILD: quic: enable early data only with >= openssl 1.1.1
- BUILD: ssl: fix the ifdef mess in ssl_sock_initial_ctx
- BUILD: quic: fix the #ifdef in ssl_quic_initial_ctx()
- MINOR: quic: add QUIC support when no client_hello_cb
- MINOR: quic: Add traces about sent or resent TX frames
- MINOR: quic: No TRACE_LEAVE() in retrieve_qc_conn_from_cid()
- BUG/MINOR: quic: Wrong connection ID to thread ID association
- BUG/MINOR: task: always reset a new tasklet's call date
- BUG/MINOR: task: make task_instant_wakeup() work on a task not a tasklet
- MINOR: task: permanently enable latency measurement on tasklets
- CLEANUP: task: rename ->call_date to ->wake_date
- BUG/MINOR: sched: properly account for the CPU time of dying tasks
- MINOR: sched: store the current profile entry in the thread context
- BUG/MINOR: stream/sched: take into account CPU profiling for the last call
- MINOR: tasks: do not keep cpu and latency times in struct task
- MINOR: tools: add generic pointer hashing functions
- CLEANUP: activity: make memprof use the generic ptr_hash() function
- CLEANUP: activity: make taskprof use ptr_hash()
- MINOR: debug: add struct ha_caller to describe a calling location
- CLEANUP: debug: use struct ha_caller for memstat
- DEBUG: task: define a series of wakeup types for tasks and tasklets
- DEBUG: task: use struct ha_caller instead of arrays of file:line
- DEBUG: applet: instrument appctx_wakeup() to log the caller's location
- DEBUG: task: simplify the caller recording in DEBUG_TASK
- CLEANUP: task: move tid and wake_date into the common part
- CLEANUP: sched: remove duplicate code in run_tasks_from_list()
- CLEANUP: activity: make the number of sched activity entries more configurable
- DEBUG: resolvers: unstatify process_resolvers() to make it appear in profiling
- DEBUG: quic: export the few task handlers that often appear in task dumps
- MEDIUM: tasks/activity: combine the called function with the caller
- MINOR: tasks/activity: improve the caller-callee activity hash
- MINOR: activity/cli: support aggregating task profiling outputs
- MINOR: activity/cli: support sorting task profiling by total CPU time
- BUG/MINOR: signals/poller: set the poller timeout to 0 when there are signals
- BUG/MINOR: quic: Speed up the handshake completion only one time
- BUG/MINOR: quic: Trace fix about packet number space information.
- BUG/MINOR: h3: Crash when h3 trace verbosity is "minimal"
- MINOR: h3: Add the quic_conn object to h3 traces
- MINOR: h3: Missing connection argument for a TRACE_LEAVE() argument
- MINOR: h3: Send the h3 settings with others streams (requests)
- MINOR: dev/udp: Apply the corruption to both directions
- BUILD: udp-perturb: Add a make target for udp-perturb tool
- BUG/MINOR: signals/poller: ensure wakeup from signals
- CI: cirrus-ci: bump FreeBSD image to 13-1
- DEV: flags: fix usage message to reflect available options
- DEV: flags: add missing CO_FL_FDLESS connection flag
- MINOR: flags: add a new file to host flag dumping macros
- MINOR: flags: implement a macro used to dump enums inside masks
- MINOR: flags/channel: use flag dumping for channel flags and analysers
- MINOR: flags/connection: use flag dumping for connection flags
- MINOR: flags/stconn: use flag dumping for stconn and sedesc flags
- MINOR: flags/stream: use flag dumping for stream error type
- MINOR: flags/stream: use flag dumping for stream flags
- MINOR: flags/task: use flag dumping for task state
- MINOR: flags/http_ana: use flag dumping for txn flags
- DEV: flags: remove the now unused SHOW_FLAG() definition
- DEV: flags: remove the now useless intermediary functions
- MINOR: flags/htx: use flag dumping to show htx and start-line flags
- MINOR: flags/http_ana: use flag dumping to show http msg states
- BUG/MEDIUM: proxy: ensure pause_proxy() and resume_proxy() own PROXY_LOCK
- MINOR: listener: small API change
- MINOR: proxy/listener: support for additional PAUSED state
- BUG/MINOR: stats: fixing stat shows disabled frontend status as 'OPEN'
- BUILD: flags: fix build warning in some macros used by show_flags
- BUILD: flags: fix the fallback macros for missing stdio
- CLEANUP: pollers: remove dead code in the polling loop
- BUG/MINOR: mux-h1: Increment open_streams counter when H1 stream is created
- REGTESTS: healthcheckmail: Relax matching on the healthcheck log message
- CLEANUP: listener: function comment typo in stop_listener()
- BUG/MINOR: listener: null pointer dereference suspected by coverity
- MINOR: flags/fd: decode FD flags states
- REORG: mux-h2: extract flags and enums into mux_h2-t.h
- MINOR: flags/mux-h2: decode H2C and H2S flags
- REGTESTS: log: test the log-forward feature
- BUG/MEDIUM: sink: bad init sequence on tcp sink from a ring.
- REGTESTS: ssl/log: test the log-forward with SSL
- MEDIUM: httpclient: httpclient_create_proxy() creates a proxy for httpclient
- MEDIUM: httpclient: allow to use another proxy
- DOC: fix TOC in starter guide for subsection 3.3.8. Statistics
- MINOR: httpclient: export httpclient_create_proxy()
- MEDIUM: quic: separate path for rx and tx with set_encryption_secrets
- BUG/MEDIUM: mux-quic: fix crash on early app-ops release
- REORG: mux-h1: extract flags and enums into mux_h1-t.h
- MINOR: flags/mux-h1: decode H1C and H1S flags
- CLEANUP: mux-quic: remove stconn usage in h3/hq
- BUG/MINOR: mux-quic: do not remotely close stream too early
- CLEANUP: exclude udp-perturb with .gitignore
- BUG/MEDIUM: server: segv when adding server with hostname from CLI
- CLEANUP: quic,ssl: fix tiny typos in C comments
- BUG/MEDIUM: captures: free() an error capture out of the proxy lock
- BUILD: fd: fix a build warning on the DWCAS
- MINOR: anon: add new macros and functions to anonymize contents
- MINOR: anon: store the anonymizing key in the global structure
- MINOR: anon: store the anonymizing key in the CLI's appctx
- MINOR: cli: anonymize commands 'show sess' and 'show sess all'
- MINOR: cli: anonymize 'show servers state' and 'show servers conn'
- MINOR: config: add command-line -dC to dump the configuration file
- SCRIPTS: announce-release: update some URLs to https
Some components like Discourse were already redirecting to https. Other
ones like docs and git are covered by the certificate, and finally
switching the advertised scheme for www should increase the ratio of
H2 and H3 in the stats (resp 8.9 and 1.9%) and possibly help spot new
issues.
This commit adds a new command line option -dC to dump the configuration
file. An optional key may be appended to -dC in order to produce an
anonymized dump using this key. The anonymizing process uses the same
algorithm as the CLI so that the same key will produce the same hashes
for the same identifiers. This way an admin may share an anonymized
extract of a configuration to match against live dumps. Note that key 0
will not anonymize the output. However, in any case, the configuration
is dumped after tokenizing, thus comments are lost.
Modify proxy.c in order to anonymize the following confidential data on
commands 'show servers state' and 'show servers conn':
- proxy name
- server name
- server address
Modify stream.c in order to hash the following confidential data if the
anonymized mode is enabled:
- configuration elements such as frontend/backend/server names
- IP addresses
In order to allow users to dump internal states using a specific key
without changing the global one, we're introducing a key in the CLI's
appctx. This key is preloaded from the global one when "set anon on"
is used (and if none exists, a random one is assigned). And the key
can optionally be assigned manually for the whole CLI session.
A "show anon" command was also added to show the anon state, and the
current key if the users has sufficient permissions. In addition, a
"debug dev hash" command was added to test the feature.
Add a uint32_t key in global to hash words with it. A new CLI command
'set global-key <key>' was added to change the global anonymizing key.
The global may also be set in the configuration using the global
"anonkey" directive. For now this key is not used.
These macros and functions will be used to anonymize strings by producing
a short hash. This will allow to match config elements against dump elements
without revealing the original data. This will later be used to anonymize
configuration parts and CLI commands output. For now only string, identifiers
and addresses are supported, but the model is easily extensible.
Ilya reported in issue #1816 a build warning on armhf (promoted to error
here since -Werror):
src/fd.c: In function fd_rm_from_fd_list:
src/fd.c:209:87: error: passing argument 3 of __ha_cas_dw discards volatile qualifier from pointer target type [-Werror=discarded-array-qualifiers]
209 | unlikely(!_HA_ATOMIC_DWCAS(((long *)&fdtab[fd].update), (uint32_t *)&cur_list.u32, &next_list.u32))
| ^~~~~~~~~~~~~~
This happens only on such an architecture because the DWCAS requires the
pointer not the value, and gcc seems to be needlessly picky about reading
a const from a volatile! This may safely be backported to older versions.
Ed Hein reported in github issue #1856 some occasional watchdog panics
in 2.4.18 showing extreme contention on the proxy's lock while the libc
was in malloc()/free(). One cause of this problem is that we call free()
under the proxy's lock in proxy_capture_error(), which makes no sense
since if we can free the object under the lock after it's been detached,
we can also free it after releasing the lock (since it's not referenced
anymore).
This should be backported to all relevant versions, likely all
supported ones.
This fixes 4 tiny and harmless typos in mux_quic.c, quic_tls.c and
ssl_sock.c. Originally sent via GitHub PR #1843.
Signed-off-by: cui fliter <imcusg@gmail.com>
[Tim: Rephrased the commit message]
[wt: further complete the commit message]
When calling 'add server' with a hostname from the cli (runtime),
str2sa_range() does not resolve hostname because it is purposely
called without PA_O_RESOLVE flag.
This leads to 'srv->addr_node.key' being NULL. According to Willy it
is fine behavior, as long as we handle it properly, and is already
handled like this in srv_set_addr_desc().
This patch fixes GH #1865 by adding an extra check before inserting
'srv->addr_node' into 'be->used_server_addr'. Insertion and removal
will be skipped if 'addr_node.key' is NULL.
It must be backported to 2.6 and 2.5 only.
udp-perturb is a tool which can be used as a UDP gateway. It can be used
to reorder, remove or corrupt datagrams. It is compiled in dev/
directory and added to .gitignore to not clutter git status output.
A stream is considered as remotely closed once we have received all the
data with the FIN bit set.
The condition to close the stream was wrong. In particular, if we
receive an empty STREAM frame with FIN bit set, this would have close
the stream even if we do not have yet received all the data. The
condition is now adjusted to ensure that Rx buffer contains all the data
up to the stream final size.
In most cases, this bug is harmless. However, if compiled with
DEBUG_STRICT=2, a BUG_ON_HOT crash would have been triggered if close is
done too early. This was most notably the case sometimes on interop test
suite with quinn or kwik clients. This can also be artificially
reproduced by simulating reception of an empty STREAM frame with FIN bit
set in qc_handle_strm_frm() :
+ if (strm_frm->fin) {
+ qcc_recv(qc->qcc, strm_frm->id, 0,
+ strm_frm->len, strm_frm->fin,
+ (char *)strm_frm->data);
+ }
ret = qcc_recv(qc->qcc, strm_frm->id, strm_frm->len,
strm_frm->offset.key, strm_frm->fin,
(char *)strm_frm->data);
This must be backported up to 2.6.
Small cleanup on snd_buf for application protocol layer.
* do not export h3_snd_buf
* replace stconn by a qcs argument. This is better as h3/hq-interop only
uses the qcs instance.
This should be backported up to 2.6.
The new functions h1c_show_flags() and h1s_show_flags() decode the flags
state into a string, and are used by dev/flags:
$ /dev/flags/flags h1c 0x2200
h1c->flags = H1C_F_ST_READY | H1C_F_ST_ATTACHED
./dev/flags/flags h1s 0x190
h1s->flags = H1S_F_BODYLESS_RESP | H1S_F_NOT_FIRST | H1S_F_WANT_KAL
The same was performed for the H2 multiplexer. H1C and H1S flags are moved
in a dedicated header file. It will be mainly used to be able to decode
mux-h1 flags from the flags utility.
In this patch, we only move the flags to mux_h1-t.h.
H3 SETTINGS emission has recently been delayed. The idea is to send it
with the first STREAM to reduce sendto syscall invocation. This was
implemented in the following patch :
3dd79d378c
MINOR: h3: Send the h3 settings with others streams (requests)
This patch works fine under nominal conditions. However, it will cause a
crash if a HTTP/3 connection is released before having sent any data,
for example when receiving an invalid first request. In this case,
qc_release will first free qcc.app_ops HTTP/3 application protocol layer
via release callback. Then qc_send is called to emit any closing frames
built by app_ops release invocation. However, in qc_send, as no data has
been sent, it will try to complete application layer protocol
intialization, with a SETTINGS emission for HTTP/3. Thus, qcc.app_ops is
reused, which is invalid as it has been just freed. This will cause a
crash with h3_finalize in the call stack.
This bug can be reproduced artificially by generating incomplete HTTP/3
requests. This will in time trigger http-request timeout without any
data send. This is done by editing qc_handle_strm_frm function.
- ret = qcc_recv(qc->qcc, strm_frm->id, strm_frm->len,
+ ret = qcc_recv(qc->qcc, strm_frm->id, strm_frm->len - 1,
strm_frm->offset.key, strm_frm->fin,
(char *)strm_frm->data);
To fix this, application layer closing API has been adjusted to be done
in two-steps. A new shutdown callback is implemented : it is used by the
HTTP/3 layer to generate GOAWAY frame in qc_release prologue.
Application layer context qcc.app_ops is then freed later in qc_release
via the release operation which is now only used to liberate app layer
ressources. This fixes the problem as the intermediary qc_send
invocation will be able to reuse app_ops before it is freed.
This patch fixes the crash, but it would be better to adjust H3 SETTINGS
emission in case of early connection closing : in this case, there is no
need to send it. This should be implemented in a future patch.
This should fix the crash recently experienced by Tristan in github
issue #1801.
This must be backported up to 2.6.
With quicTLS the set_encruption_secrets callback is always called with
the read_secret and the write_secret.
However this is not the case with libreSSL, which uses the
set_read_secret()/set_write_secret() mecanism. It still provides the
set_encryption_secrets() callback, which is called with a NULL
parameter for the write_secret during the read, and for the read_secret
during the write.
The exchange key was not designed in haproxy to be called separately for
read and write, so this patch allow calls with read or write key to
NULL.
This subsection has been moved from 3.4.9 to 3.3.8 somewhere along
2.4, but the TOC has not been updated - resulting in a invalid
anchor in the HTML version.
Needs to be backported to 2.4+
httpclient_new_from_proxy() is a variant of httpclient_new() which
allows to create the requests from a different proxy.
The proxy and its 2 servers are now stored in the httpclient structure.
The proxy must have been created with httpclient_create_proxy() to be
used.
The httpclient_postcheck() callback will finish the initialization of
all proxies created with PR_CAP_HTTPCLIENT.
httpclient_create_proxy() is a function which creates a proxy that could
be used for the httpclient. It will allocate a proxy, a raw server and
an ssl server.
This patch moves most of the code from httpclient_precheck() into a
generic function httpclient_create_proxy().
The proxy will have the PR_CAP_HTTPCLIENT capability.
This could be used for specifics httpclient instances that needs
different proxy settings.
The init of tcp sink, particularly for SSL, was done
too early in the code, during parsing, and this can cause
a crash specially if nbthread was not configured.
This was detected by William using ASAN on a new regtest
on log forward.
This patch adds the 'struct proxy' created for a sink
to a list and this list is now submitted to the same init
code than the main proxies list or the log_forward's proxies
list. Doing this, we are assured to use the right init sequence.
It also removes the ini code for ssl from post section parsing.
This patch should be backported as far as v2.2
Note: this fix uses 'goto' labels created by commit
'BUG/MAJOR: log-forward: Fix log-forward proxies not fully initialized'
but this code didn't exist before v2.3 so this patch needs to be
adapted for v2.2.
The new functions h2c_show_flags() and h2s_show_flags() decode the flags
state into a string, and are used by dev/flags:
$ ./dev/flags/flags h2c 0x0600
h2c->flags = H2_CF_DEM_IN_PROGRESS | H2_CF_DEM_SHORT_READ
$ ./dev/flags/flags h2s 0x7003
h2s->flags = H2_SF_HEADERS_RCVD | H2_SF_OUTGOING_DATA | H2_SF_HEADERS_SENT \
| H2_SF_ES_SENT | H2_SF_ES_RCVD
Originally in 1.8 we wanted to have an independent mux that could possibly
be disabled and would not impose dependencies on the outside. Everything
would fit into a single C file and that was fine.
Nowadays muxes are unavoidable, and not being able to easily inspect them
from outside is sometimes a bit of a pain. In particular, the flags utility
still cannot be used to decode their flags.
As a first step towards this, this patch moves the flags and enums to
mux_h2-t.h, as well as the two state decoding inline functions. It also
dropped the H2_SS_*_BIT defines that nobody uses. The mux_h2.c file remains
the only one to include that for now.
The new function is fd_show_flags() and it reports known FD flags:
$ ./dev/flags/flags fd 0x000121
fd->flags = FD_POLL_IN | FD_EV_READY_W | FD_EV_ACTIVE_R
Please refer to GH #1859 for more info.
Coverity suspected improper proxy pointer handling.
Without the fix it is considered safe for the moment, but it might not
be the case in the future as we want to keep the ability to have
isolated listeners.
Making sure stop_listener(), pause_listener(), resume_listener()
and listener_release() functions make proper use
of px pointer in that context.
No need for backport except if multi-connection protocols (ie:FTP)
were to be backported as well.
Depending on the timing, the conneciton on lisrv listener may be fully
accepted before any reject. Thus, instead of getting a socket error, an
invalid L7 response is reported. There is no reason to be strick on the
error type. Any failure is good here, because we just want to test the
email-alert feature.
This patch should fix issue #1857. It may be backported as far as 2.2.
Since this counter was added, it was incremented at the wrong place for
client streams. It was incremented when the stream-connector (formely the
conn-stream) was created while it should be done when the H1 stream is
created. Thus, on parsing error, on H1>H2 upgrades or TCP>H1 upgrades, the
counter is not incremented. However, it is always decremented when the H1
stream is destroyed.
On bakcned side, there is no issue.
This patch must be backported to 2.6.
As reported by Ilya and Coverity in issue #1858, since recent commit
eea152ee6 ("BUG/MINOR: signals/poller: ensure wakeup from signals")
which removed the test for the global signal flag from the pollers'
loop, the remaining "wake" flag doesn't need to be tested since it
already participates to zeroing the wait_time and will be caught
on the previous line.
Let's just remove that test now.
