Since the reload is now synchronous over the master CLI, try to reload
with it. This was a problem before with the signals because it wasn't
possible to wait for the end of the reload before sending the requests.
This activate again this test, we will see if it's more stable or we
will deactivate it again..
With the CI occasionally slowing down, we're starting to see again some
spurious failures despite the long 1-second timeouts. This reports false
positives that are disturbing and doesn't provide as much value as this
could. However at this delay it already becomes a pain for developers
to wait for the tests to complete.
This commit adds support for the new environment variable
HAPROXY_TEST_TIMEOUT that will allow anyone to modify the connect,
client and server timeouts. It was set to 5 seconds by default, which
should be plenty for quite some time in the CI. All relevant values
that were 200ms or above were replaced by this one. A few larger
values were left as they are special. One test for the set-timeout
action that used to rely on a fixed 1-sec value was extended to a
fixed 5-sec, as the timeout is normally not reached, but it needs
to be known to compare the old and new values.
There is apparently a race in this test that would require relying on
haproxy's output to make it reliably work, but currently vtest doesn't
have this option. Let's mark it broken again to avoid polluting the CI.
This is discussed in github issue #950.
William noticed that the real issue in the abns test was that it was
failing to rebind some listeners, issues which were addressed in the
previous commits (in some cases, the master would even accept traffic
on the worker's socket which was not properly disabled, causing some
of the strange error messages).
The other issue documented in commit 2ea15a080 was the lack of
reliability when the test was run in parallel. This is caused by the
abns socket which uses a hard-coded address, making all tests in
parallel to step onto each others' toes. Since vtest cannot provide
abns sockets, we're instead concatenating the number of the listening
port that vtest allocated for another frontend to the abns path, which
guarantees to make them unique in the system.
The test works fine in all cases now, even with 100 in parallel.
This test is inherently racy. It regularly pops up on the CI, and I've
spent one hour chasing a bug that apparently doesn't exist, just because
I'm running it 10 times in a row and it reports from 4 to 8 failures
when built at -O2 and generally even more at -O0. The logs are very
confusing, often reporting that it failed with status 0, with nothing
else wrong. I suspect it might sometimes be the shell command that fails
if it executes faster than haproxy finishes to start up, which would
also explain the relation with the optimization level. E.g:
> Testing with haproxy version: 2.2.0
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.006) exit=2
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.006) exit=2
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.009) exit=2
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.008) exit=2
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.007) exit=2
> # top TEST reg-tests/seamless-reload/abns_socket.vtc FAILED (3.007) exit=2
> 6 tests failed, 0 tests skipped, 4 tests passed
Some of the failures include this, suggesting that some barriers could
help:
---- h1 haproxy h1 PID file check failed:
Could not read PID file '/tmp/haregtests-2020-10-09_11-19-40.kgsDB4/vtc.30539.04dbea7f/h1/pid
Since it has been causing false positives and consumed way more
troubleshooting time than it saved, let's mark it as broken so that it
doesn't waste more time. We can bring it back when someone manages to
figure what the problem is.
The abns_socket in seamless-reload regtest regularly fails in Travis-CI
on smaller machines only (typically the ppc64le and sometimes s390x).
The error always reports an incomplete HTTP header as seen from the
client. And this can occasionally be reproduced on the minicloud ppc64le
image when setting a huge file descriptors limit (1 million).
What happens in fact is the following: depending on the binding order,
some connections from the client might reach the TCP listener on the
old instance and be forwarded to the ABNS listener of the second
instance just being prepared to start up. But due to the huge number
of FDs, setting them up takes slightly more time and the 20ms server
timeout may expire before the new instance finishes its startup. This
can result in an occasional 504, except that since the client timeout
is the same as the server timeout, both sides are closed at the same
time and the client doesn't receive the 504.
In addition a second problem plugs onto this: by default http-reuse is
enabled. Some requests being forwarded to the older instance will be
sent over an already established connection. But the CPU used by the
starting process using many FDs will be taken away from the older
process, whose abns listener will not see a request for more than 20ms,
and will decide to kill the idle client connection. At the same moment
the TCP proxy forwards a request over this closing connection, it
detects the close and silently closes the other side to let the
client retry, which is detected by the vtest client as another case
of empty header. This is easier to reproduce in VMs with few CPUs
(2 or less) and some noisy neighbors such as a few spinning loops in
background.
Let's just increase this tests' timeout to avoid this. While a few
ms are close to the scheduler's granularity, this test is never
supposed to trigger the timeouts so it's safe to go higher without
impacts on the test execution time. At one second the problem seems
impossible to reproduce on the minicloud VMs.
VTest can now enable mworker and mcli with separate flags so lets
update vtc files that need it. This also allows to revert the change
made with 1545a59c ("REGTESTS: make seamless-reload depend on 1.9
and above").
Since latest updates, vtest requires the master CLI when running in
master-worker mode, and this one is only available starting with 1.9.
The seamless reload test is the only one depending on this and now
fails on 1.8, so let's adjust it accordingly.
This patch replaces LEVEL variable by REGTESTS_TYPES variable which is more
mnemonic and human readable. It is uses as a filter to run the reg tests scripts
where a commented #REGTEST_TYPE may be defined to designate their types.
Running the following command:
$ REGTESTS_TYPES=slow,default
will start all the reg tests where REGTEST_TYPE is defines as 'slow' or 'default'.
Note that 'default' is also the default value of REGTEST_TYPE when not specified
dedicated to run all the current h*.vtc files. When REGTESTS_TYPES is not specified
there is no filter at all. All the tests are run.
This patches also defines REGTEST_TYPE with 'slow' value for all the s*.vtc files,
'bug' value for al the b*.vtc files, 'broken' value for all the k*.vtc files.
Add LEVEL #4 regression testing files which is dedicated to
VTC files in relation with bugs they help to reproduce.
At the date of this commit, all VTC files are LEVEL 4 VTC files.
