The patch "MINOR: systemd: Make use of master socket in systemd unit"
introduces an environment file in /etc/default.
Unfortunatly this is not supported on redhat-based system, so we add
/etc/sysconfig/haproxy for that.
Unless the EXTRAOPTS variable is overriden in /etc/default/haproxy
the unit file will use the master socket by default.
This patch may be backported to 1.9 and depends on
MINOR: systemd: Use the variables from /etc/default/haproxy.
This will allow seamless upgrades from the sysvinit system while respecting
any changes the users may have made. It will also make local configuration
easier than overriding the systemd unit file.
Note by Tim:
This GPL-2 licensed patch was taken from the Debian project at [1].
It was slightly modified to cleanly apply, because HAProxy's default unit
file does not include rsyslog.service as an 'After' dependency. Also the
subject line was modified to include the proper subsystem and severity.
This patch may be backported to 1.9.
[1] https://salsa.debian.org/haproxy-team/haproxy/blob/master/debian/patches/haproxy.service-use-environment-variables.patch
Co-authored-by: Tim Duesterhus <tim@bastelstu.be>
The master process will exit with the status of the last worker. When
the worker is killed with SIGTERM, it is expected to get 143 as an
exit status. Therefore, we consider this exit status as normal from a
systemd point of view. If it happens when not stopping, the systemd
unit is configured to always restart, so it has no adverse effect.
This has mostly a cosmetic effect. Without the patch, stopping HAProxy
leads to the following status:
● haproxy.service - HAProxy Load Balancer
Loaded: loaded (/lib/systemd/system/haproxy.service; disabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Fri 2018-06-22 20:35:42 CEST; 8min ago
Docs: man:haproxy(1)
file:/usr/share/doc/haproxy/configuration.txt.gz
Process: 32715 ExecStart=/usr/sbin/haproxy -Ws -f $CONFIG -p $PIDFILE $EXTRAOPTS (code=exited, status=143)
Process: 32714 ExecStartPre=/usr/sbin/haproxy -f $CONFIG -c -q $EXTRAOPTS (code=exited, status=0/SUCCESS)
Main PID: 32715 (code=exited, status=143)
After the patch:
● haproxy.service - HAProxy Load Balancer
Loaded: loaded (/lib/systemd/system/haproxy.service; disabled; vendor preset: enabled)
Active: inactive (dead)
Docs: man:haproxy(1)
file:/usr/share/doc/haproxy/configuration.txt.gz
While the haproxy workers usually are running chrooted the master
process is not. This patch is a pretty safe defense in depth measure
to ensure haproxy cannot touch sensitive parts of the file system.
ProtectSystem takes non-boolean arguments in newer SystemD versions,
but setting those would leave older systems such as Ubuntu Xenial
unprotected. Distro maintainers and system administrators could
adapt the ProtectSystem value to the SystemD version they ship.
This variable was used by the wrapper which was removed in
a6cfa9098e. The correct way to do seamless reload is now to enable
"expose-fd listeners" on the stat socket.
This patch adds support for `Type=notify` to the systemd unit.
Supporting `Type=notify` improves both starting as well as reloading
of the unit, because systemd will be let known when the action completed.
See this quote from `systemd.service(5)`:
> Note however that reloading a daemon by sending a signal (as with the
> example line above) is usually not a good choice, because this is an
> asynchronous operation and hence not suitable to order reloads of
> multiple services against each other. It is strongly recommended to
> set ExecReload= to a command that not only triggers a configuration
> reload of the daemon, but also synchronously waits for it to complete.
By making systemd aware of a reload in progress it is able to wait until
the reload actually succeeded.
This patch introduces both a new `USE_SYSTEMD` build option which controls
including the sd-daemon library as well as a `-Ws` runtime option which
runs haproxy in master-worker mode with systemd support.
When haproxy is running in master-worker mode with systemd support it will
send status messages to systemd using `sd_notify(3)` in the following cases:
- The master process forked off the worker processes (READY=1)
- The master process entered the `mworker_reload()` function (RELOADING=1)
- The master process received the SIGUSR1 or SIGTERM signal (STOPPING=1)
Change the unit file to specify `Type=notify` and replace master-worker
mode (`-W`) with master-worker mode with systemd support (`-Ws`).
Future evolutions of this feature could include making use of the `STATUS`
feature of `sd_notify()` to send information about the number of active
connections to systemd. This would require bidirectional communication
between the master and the workers and thus is left for future work.
Adding Type=forking in the unit file ensure better monitoring from
systemd. During a systemctl start the tool is able to return an error if
it didn't work with this option.
Make the systemd wrapper chech if HAPROXY_STATS_SOCKET if set.
If set, it will use it as an argument to the "-x" option, which makes
haproxy asks for any listening socket, on the stats socket, in order
to achieve reloads with no new connection lost.
Users can set the location of haproxy.cfg and pidfile files by providing
a systemd overwrite file /etc/systemd/system/haproxy.service.d/overwrite.conf
with the following content:
[Service]
Environment=CONFIG=/etc/foobar/haproxy.cfg
By default systemd will send SIGTERM to all processes in the service's
control group. In our case, this includes the wrapper, the master
process and all worker processes.
Since commit c54bdd2a the wrapper actually catches SIGTERM and survives
to see the master process getting killed by systemd and regard this as
an error, placing the unit in a failed state during "systemctl stop".
Since the wrapper now handles SIGTERM by itself, we switch the kill mode
to 'mixed', which means that systemd will deliver the initial SIGTERM to
the wrapper only, and if the actual haproxy processes don't exit after a
given amount of time (default: 90s), a SIGKILL is sent to all remaining
processes in the control group. See systemd.kill(5) for more
information.
This should also be backported to 1.5.
