51 lines
2.1 KiB
INI
51 lines
2.1 KiB
INI
|
#
|
||
|
|
# This is an example of how to configure HAProxy to be used as a 'full transparent proxy' for a single backend server.
|
||
|
|
#
|
||
|
|
# Note that to actually make this work extra firewall/nat rules are required.
|
||
|
|
# Also HAProxy needs to be compiled with support for this, in HAProxy1.5-dev19 you can check if this is the case with "haproxy -vv".
|
||
|
|
#
|
||
|
|
|
||
|
|
global
|
||
|
|
frontend MyFrontend
|
||
|
|
bind 192.168.1.22:80
|
||
|
|
default_backend TransparentBack_http
|
||
|
|
|
||
|
|
backend TransparentBack_http
|
||
|
|
mode http
|
||
|
|
source 0.0.0.0 usesrc client
|
||
|
|
server MyWebServer 192.168.0.40:80
|
||
|
|
|
||
|
|
#
|
||
|
|
# To create the the nat rules perform the following:
|
||
|
|
#
|
||
|
|
# ### (FreeBSD 8) ###
|
||
|
|
# --- Step 1 ---
|
||
|
|
# ipfw is needed to get 'reply traffic' back to the HAProxy process, this can be achieved by configuring a rule like this:
|
||
|
|
# fwd localhost tcp from 192.168.0.40 80 to any in recv em0
|
||
|
|
#
|
||
|
|
# The following would be even better but this did not seam to work on the pfSense2.1 distribution of FreeBSD 8.3:
|
||
|
|
# fwd 127.0.0.1:80 tcp from any 80 to any in recv ${outside_iface} uid ${proxy_uid}
|
||
|
|
#
|
||
|
|
# If only 'pf' is currently used some aditional steps are needed to load and configure ipfw:
|
||
|
|
# You need to configure this to always run on startup:
|
||
|
|
#
|
||
|
|
# /sbin/kldload ipfw
|
||
|
|
# /sbin/sysctl net.inet.ip.pfil.inbound="pf" net.inet6.ip6.pfil.inbound="pf" net.inet.ip.pfil.outbound="pf" net.inet6.ip6.pfil.outbound="pf"
|
||
|
|
# /sbin/sysctl net.link.ether.ipfw=1
|
||
|
|
# ipfw add 10 fwd localhost tcp from 192.168.0.40 80 to any in recv em0
|
||
|
|
#
|
||
|
|
# the above does the folowing:
|
||
|
|
# - load the ipfw kernal module
|
||
|
|
# - set pf as the outer firewall to keep control of routing packets for example to route them to a non-default gateway
|
||
|
|
# - enable ipfw
|
||
|
|
# - set a rule to catches reply traffic on em0 comming from the webserver
|
||
|
|
#
|
||
|
|
# --- Step 2 ---
|
||
|
|
# To also make the client connection transparent its possible to redirect incomming requests to HAProxy with a pf rule:
|
||
|
|
# rdr on em1 proto tcp from any to 192.168.0.40 port 80 -> 192.168.1.22
|
||
|
|
# here em1 is the interface that faces the clients, and traffic that is originally send straight to the webserver is redirected to HAProxy
|
||
|
|
#
|
||
|
|
# ### (FreeBSD 9) (OpenBSD 4.4) ###
|
||
|
|
# pf supports "divert-reply" which is probably better suited for the job above then ipfw..
|
||
|
|
#
|