ceph/doc/rados/configuration/msgr2.rst
Zac Dover 239e7c0e68 doc/rados: add prompts to msgr2.rst
Add unselectable prompts to doc/rados/configuration/msgr2.rst.

https://tracker.ceph.com/issues/57108

Signed-off-by: Zac Dover <zac.dover@gmail.com>
2022-12-20 03:41:22 +10:00

259 lines
9.4 KiB
ReStructuredText

.. _msgr2:
Messenger v2
============
What is it
----------
The messenger v2 protocol, or msgr2, is the second major revision on
Ceph's on-wire protocol. It brings with it several key features:
* A *secure* mode that encrypts all data passing over the network
* Improved encapsulation of authentication payloads, enabling future
integration of new authentication modes like Kerberos
* Improved earlier feature advertisement and negotiation, enabling
future protocol revisions
Ceph daemons can now bind to multiple ports, allowing both legacy Ceph
clients and new v2-capable clients to connect to the same cluster.
By default, monitors now bind to the new IANA-assigned port ``3300``
(ce4h or 0xce4) for the new v2 protocol, while also binding to the
old default port ``6789`` for the legacy v1 protocol.
.. _address_formats:
Address formats
---------------
Prior to Nautilus, all network addresses were rendered like
``1.2.3.4:567/89012`` where there was an IP address, a port, and a
nonce to uniquely identify a client or daemon on the network.
Starting with Nautilus, we now have three different address types:
* **v2**: ``v2:1.2.3.4:578/89012`` identifies a daemon binding to a
port speaking the new v2 protocol
* **v1**: ``v1:1.2.3.4:578/89012`` identifies a daemon binding to a
port speaking the legacy v1 protocol. Any address that was
previously shown with any prefix is now shown as a ``v1:`` address.
* **TYPE_ANY** ``any:1.2.3.4:578/89012`` identifies a client that can
speak either version of the protocol. Prior to nautilus, clients would appear as
``1.2.3.4:0/123456``, where the port of 0 indicates they are clients
and do not accept incoming connections. Starting with Nautilus,
these clients are now internally represented by a **TYPE_ANY**
address, and still shown with no prefix, because they may
connect to daemons using the v2 or v1 protocol, depending on what
protocol(s) the daemons are using.
Because daemons now bind to multiple ports, they are now described by
a vector of addresses instead of a single address. For example,
dumping the monitor map on a Nautilus cluster now includes lines
like::
epoch 1
fsid 50fcf227-be32-4bcb-8b41-34ca8370bd16
last_changed 2019-02-25 11:10:46.700821
created 2019-02-25 11:10:46.700821
min_mon_release 14 (nautilus)
0: [v2:10.0.0.10:3300/0,v1:10.0.0.10:6789/0] mon.foo
1: [v2:10.0.0.11:3300/0,v1:10.0.0.11:6789/0] mon.bar
2: [v2:10.0.0.12:3300/0,v1:10.0.0.12:6789/0] mon.baz
The bracketed list or vector of addresses means that the same daemon can be
reached on multiple ports (and protocols). Any client or other daemon
connecting to that daemon will use the v2 protocol (listed first) if
possible; otherwise it will back to the legacy v1 protocol. Legacy
clients will only see the v1 addresses and will continue to connect as
they did before, with the v1 protocol.
Starting in Nautilus, the ``mon_host`` configuration option and ``-m
<mon-host>`` command line options support the same bracketed address
vector syntax.
Bind configuration options
^^^^^^^^^^^^^^^^^^^^^^^^^^
Two new configuration options control whether the v1 and/or v2
protocol is used:
* :confval:`ms_bind_msgr1` [default: true] controls whether a daemon binds
to a port speaking the v1 protocol
* :confval:`ms_bind_msgr2` [default: true] controls whether a daemon binds
to a port speaking the v2 protocol
Similarly, two options control whether IPv4 and IPv6 addresses are used:
* :confval:`ms_bind_ipv4` [default: true] controls whether a daemon binds
to an IPv4 address
* :confval:`ms_bind_ipv6` [default: false] controls whether a daemon binds
to an IPv6 address
.. note:: The ability to bind to multiple ports has paved the way for
dual-stack IPv4 and IPv6 support. That said, dual-stack support is
not yet tested as of Nautilus v14.2.0 and likely needs some
additional code changes to work correctly.
Connection modes
----------------
The v2 protocol supports two connection modes:
* *crc* mode provides:
- a strong initial authentication when the connection is established
(with cephx, mutual authentication of both parties with protection
from a man-in-the-middle or eavesdropper), and
- a crc32c integrity check to protect against bit flips due to flaky
hardware or cosmic rays
*crc* mode does *not* provide:
- secrecy (an eavesdropper on the network can see all
post-authentication traffic as it goes by) or
- protection from a malicious man-in-the-middle (who can deliberate
modify traffic as it goes by, as long as they are careful to
adjust the crc32c values to match)
* *secure* mode provides:
- a strong initial authentication when the connection is established
(with cephx, mutual authentication of both parties with protection
from a man-in-the-middle or eavesdropper), and
- full encryption of all post-authentication traffic, including a
cryptographic integrity check.
In Nautilus, secure mode uses the `AES-GCM
<https://en.wikipedia.org/wiki/Galois/Counter_Mode>`_ stream cipher,
which is generally very fast on modern processors (e.g., faster than
a SHA-256 cryptographic hash).
Connection mode configuration options
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
For most connections, there are options that control which modes are used:
.. confval:: ms_cluster_mode
.. confval:: ms_service_mode
.. confval:: ms_client_mode
There are a parallel set of options that apply specifically to
monitors, allowing administrators to set different (usually more
secure) requirements on communication with the monitors.
.. confval:: ms_mon_cluster_mode
.. confval:: ms_mon_service_mode
.. confval:: ms_mon_client_mode
Compression modes
-----------------
The v2 protocol supports two compression modes:
* *force* mode provides:
- In multi-availability zones deployment, compressing replication messages between OSDs saves latency.
- In the public cloud, inter-AZ communications are expensive. Thus, minimizing message
size reduces network costs to cloud provider.
- When using instance storage on AWS (probably other public clouds as well) the instances with NVMe
provide low network bandwidth relative to the device bandwidth.
In this case, NW compression can improve the overall performance since this is clearly
the bottleneck.
* *none* mode provides:
- messages are transmitted without compression.
Compression mode configuration options
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
For all connections, there is an option that controls compression usage in secure mode
.. confval:: ms_compress_secure
There is a parallel set of options that apply specifically to OSDs,
allowing administrators to set different requirements on communication between OSDs.
.. confval:: ms_osd_compress_mode
.. confval:: ms_osd_compress_min_size
.. confval:: ms_osd_compression_algorithm
Transitioning from v1-only to v2-plus-v1
----------------------------------------
By default, ``ms_bind_msgr2`` is true starting with Nautilus 14.2.z.
However, until the monitors start using v2, only limited services will
start advertising v2 addresses.
For most users, the monitors are binding to the default legacy port ``6789``
for the v1 protocol. When this is the case, enabling v2 is as simple as:
.. prompt:: bash $
ceph mon enable-msgr2
If the monitors are bound to non-standard ports, you will need to
specify an additional port for v2 explicitly. For example, if your
monitor ``mon.a`` binds to ``1.2.3.4:1111``, and you want to add v2 on
port ``1112``:
.. prompt:: bash $
ceph mon set-addrs a [v2:1.2.3.4:1112,v1:1.2.3.4:1111]
Once the monitors bind to v2, each daemon will start advertising a v2
address when it is next restarted.
.. _msgr2_ceph_conf:
Updating ceph.conf and mon_host
-------------------------------
Prior to Nautilus, a CLI user or daemon will normally discover the
monitors via the ``mon_host`` option in ``/etc/ceph/ceph.conf``. The
syntax for this option has expanded starting with Nautilus to allow
support the new bracketed list format. For example, an old line
like::
mon_host = 10.0.0.1:6789,10.0.0.2:6789,10.0.0.3:6789
Can be changed to::
mon_host = [v2:10.0.0.1:3300/0,v1:10.0.0.1:6789/0],[v2:10.0.0.2:3300/0,v1:10.0.0.2:6789/0],[v2:10.0.0.3:3300/0,v1:10.0.0.3:6789/0]
However, when default ports are used (``3300`` and ``6789``), they can
be omitted::
mon_host = 10.0.0.1,10.0.0.2,10.0.0.3
Once v2 has been enabled on the monitors, ``ceph.conf`` may need to be
updated to either specify no ports (this is usually simplest), or
explicitly specify both the v2 and v1 addresses. Note, however, that
the new bracketed syntax is only understood by Nautilus and later, so
do not make that change on hosts that have not yet had their ceph
packages upgraded.
When you are updating ``ceph.conf``, note the new ``ceph config
generate-minimal-conf`` command (which generates a barebones config
file with just enough information to reach the monitors) and the
``ceph config assimilate-conf`` (which moves config file options into
the monitors' configuration database) may be helpful. For example,::
# ceph config assimilate-conf < /etc/ceph/ceph.conf
# ceph config generate-minimal-config > /etc/ceph/ceph.conf.new
# cat /etc/ceph/ceph.conf.new
# minimal ceph.conf for 0e5a806b-0ce5-4bc6-b949-aa6f68f5c2a3
[global]
fsid = 0e5a806b-0ce5-4bc6-b949-aa6f68f5c2a3
mon_host = [v2:10.0.0.1:3300/0,v1:10.0.0.1:6789/0]
# mv /etc/ceph/ceph.conf.new /etc/ceph/ceph.conf
Protocol
--------
For a detailed description of the v2 wire protocol, see :ref:`msgr2-protocol`.